Abstract:This article has been retracted: please see Elsevier Policy on Article Withdrawal (https://www.elsevier.com/about/our-business/policies/article-withdrawal). <This article has been retracted: please see Elsevier Policy on Article Withdrawal (http://www.elsevier.com/locate/withdrawalpolicy). This article has been retracted at the request of the Editor. Figure 5 duplicates figure 8 of the article that had already appeared in Materials Characterization 98 (2014) 147–161, http://dx.doi.org/10.1016/j.matchar.2014.10.026, figure 12 of the paper that had appeared in Applied Physics A 117 (2014) 2251-2264, http://dx.doi.org/10.1007/s00339-014-8655-1, as well as panels from figure 12 of the article that had appeared in the Journal of Alloys and Compounds 616 (2014) 173–183, http://dx.doi.org/10.1016/j.jallcom.2014.07.143. Figure 6 duplicates figure 9 of the article that had already appeared in Materials Characterization 98 (2014) 147–161, http://dx.doi.org/10.1016/j.matchar.2014.10.026 and figure 13 of the article that had appeared in the Journal of Alloys and Compounds 616 (2014) 173–183, http://dx.doi.org/10.1016/j.jallcom.2014.07.143. Figure 7 duplicates figure 10 of the article that had already appeared in Surface & Coatings Technology 258 (2014) 467–484, http://dx.doi.org/10.1016/j.surfcoat.2014.08.052. One of the conditions of submission of a paper for publication is that authors declare explicitly that their work is original and has not appeared in a publication elsewhere. Re-use of any data should be appropriately cited. As such this article represents an abuse of the scientific publishing system. The scientific community takes a very strong view on this matter and apologies are offered to readers of the journal that this was not detected during the submission process. Journal records indicate that confirmation of the submission and publication of the article was sent to the first author's email address, in addition to an email that used the corresponding author's name (guoyitangforwork@163.com). The corresponding author and the first author wish to mention that the co-author Zion T.H. Tse was not involved in the preparation and handling of this article. He was not informed about the publication and he did not grant the use of his name and affiliation in the publication. Prof. S. Petter Lyngstadaas, Dr. Hanna Tiainen and Dr. Sebastian Geissler from University of Oslo are acknowledged for the considerable effort put into collecting the evidence and reporting this case of multiple publication.)> © 2018

WITHDRAWN: Development of a New Micro Punching Machine with Micro Male and Female Dies Fabricated Online

WITHDRAWN: A Study of the Integrated Composite Material Structures under Different Fabrication Processing

WITHDRAWN: Microfabrication-based Engineering of the Embryonic and Adult Stem Cell Niches

WITHDRAWN: Preface

WITHDRAWN: Feasibility Study on Rapid Prototyping of Porcelain Products

Retraction notice to: “Effect of electropulsing treatment on microstructure and mechanical properties of cold-rolled pure titanium strips” (Journal of Materials Processing Tech. (2015) 222 (27–32), (S0924013615000850), (10.1016/j.jmatprotec.2015.02.035))

Retraction notice to “Influence of electropulsing treatment on microstructure and mechanical properties of Ti-6Al-4V alloy strip with lamellar microstructure” [Mater. Sci. Eng. A 622 (2015) 1−6](S0921509314013422)(10.1016/j.msea.2014.11.003)

WITHDRAWN: Expression and Distribution of Dlg1 During Meiotic Maturation in Mouse Oocytes

RETRACTED: Microstructure and Tribological Characterizations of Ni-based Self-Lubricating Coating

RETRACTED: Dong et al. Transient Response Characteristics Analysis of High-Power Piezoelectric Transducers. Micromachines 2022, 13, 1638

WITHDRAWN: Experimental and Numerical Analysis of Local Reinforced Bolted Composite Joint

Retracted: Design and Experiments of a Hybrid Wind Turbine Drive Train Using Both Hydraulic and Mechanical Transmissions

Retraction notice to “ Effects of high-energy electro-pulsing treatment on microstructure, mechanical properties and corrosion behavior of Ti–6Al–4V alloy” [MSEC Volume 49, Year 2015, Pages 851-860](S0928493115000910)(10.1016/j.msec.2015.01.081)

WITHDRAWN: Strain Rate and Temperature Effects on the Mechanical Properties of Cured Isotropic Conductive Adhesive (ICA) at Micro Scale

Retracted: Development of Intelligent CAD Technology for New Longitudinal Shell-Side Heat Exchange Equipment

WITHDRAWN: Microstructure and Properties of Welded Joint for T92 Ferritic Heat Resistant Steel

RETRACTED: Mechanical properties and phase transition of biomedical titanium alloy strips with initial quasi-single phase state under high-energy electropulses

RETRACTED: Effect of Electropulsing Treatment and Ultrasonic Striking Treatment on the Mechanical Properties and Microstructure of Biomedical Ti-6Al-4v Alloy

WITHDRAWN: User Attractor: an Operator for the Evaluation of Social Influence

Retracted: Design and Control of a High-Speed Switched Reluctance Machine with Conical Magnetic Bearings for Aircraft Application

WITHDRAWN: High Cycle Fatigue Behavior of Extruded Mg–Zn–Y–Zr Alloys Containing Varying Contents of Yttrium