Abstract:The class of NbC-Ni cermets has emerged as a promising environmentally friendly alternative to WC-Co cemented carbide tools, although some inherent properties i.e. room temperature hardness and flexural strength, of NbC-Ni cermets may require further enhancements. To enhance the properties of NbC-Ni cermets, diverse methodologies were applied, including grain inhibition and the strengthening of the cermet through the use of reinforcements. This study systematically examined the impact of TiC additions, specifically at 10% and 20%, on both the microstructure and mechanical properties of NbC-12Ni-4VC-4Mo2C cermets. NbC-12Ni cermets were fabricated via vacuum liquid phase sintering (LPS) at 1400°C and 1450°C. Enhancements by incorporating 4% VC and 4% Mo2C, followed by TiC at 10% and 20% concentrations to the NbC-Ni-4VC4Mo2C cermet were made. XRD and SEM results confirm the formation of (Nb, X, Y) C solid solution cubic FCC carbides. Significant grain refinement was evident in the cermet samples, subjected to grain inhibition. The observed grain sizes ranged from a maximum of 6.84 μm (in NbC12Ni) to a minimum of 2.154 μm (in the sample containing 20% TiC) at 1450°C. The incorporation of 20TiC at 1450°C led to a remarkable 26.5% enhancement in average hardness compared to NbC-Ni cermet, and a 4.2% improvement over the 4VC4Mo2C cermet. At 1450°C, 20TiC reinforcement led to an average fracture toughness of 9.331 MPa√m, representing a 4.56% improvement over the 4VC4Mo2C cermet. However, there was a marginal reduction in toughness compared to the NbC-Ni cermet. Moreover, the addition of TiC led to a decrease in the flexural strength of the cermets, with a maximum flexural strength of 939 N/mm2 recorded for NbC-Ni-4VC4Mo2C, representing an 11.6% increase compared to the NbC-Ni cermet.

Abstracts for November 1999 Journal of Materials Research

Abstracts for April 1999 Journal of Materials Research

Abstracts for February 1998 Journal of Materials Research

Abstracts for February 1996 Journal of Materials Research

Interface characterization and mechanical properties of Mo-added chromium carbide-nickel composite

Experimental Investigation and Thermodynamic Analysis of TiC–Fe Cermets with Mo Additions

Synthesis and characterization of Mo@Ni core-shell composite powder-reinforced (W,Ti)C-based cermet

Evolution of microstructure and interfacial characteristics of complete solid-solution Ti(C,N)-based cermets fabricated by mechanical activation and subsequent in situ carbothermal reduction

Effects of WC content on core/rim phases and microstructure of TiB2-TiC-WC-(Co-Ni) cermets

Influence of Mo addition on microstructure and mechanical properties of Ti(C,N)-based cermets fabricated by in-situ carbothermal reduction of TiO2

Effects of WC/TiC addition on the thermodynamic behavior of TiB 2 -based cermet during sintering process

Polycrystal model of the mechanical behavior of a Mo-TiC30vol.% metal-ceramic composite using a 3D microstructure map obtained by a dual beam FIB-SEM

Reciprocating Wear Performance and Interfacial Microstructure of a TiC–Ni 2 AlTi Cermet

Synthesis of TiB 2 /Ti(C,N) cermet by RSPS: formation mechanism, shrinkage behavior, and mechanical properties

Microstructure and Mechanical Properties of TiC Reinforced NbC-Ni4VC4Mo2C Cermets

Microstructure, Mechanical and Tribological Properties of High-Entropy Carbide (MoNbTaTiV)C5

Effect of carbon content and cooling rate on the microstructure and hardness of TiC-Fe-Cr-Mo cermets

Friction and wear behavior of Ti(C,N) self-lubricating cermet materials with multilayer core-shell microstructure

Effect of TiC content on the microstructure and mechanical properties of Ti-30Mo-xTiC composites

Phase and crystallite size analysis of (Ti1-xMox)C-(Ni,Cr) cermet obtained by mechanical alloying

Formation of solid solution structures in (Ti,W,Ta,Mo)(C,N) cermet via spark plasma sintering