Abstract:The anisotropic behavior of as-extruded 7003 aluminum alloy under quasi-static compression and high-speed impact was studied using samples with axes parallel to extrusion direction (ED) (0 degrees sample), at an angle of 45 degrees to ED (45 degrees sample), and perpendicular to ED (90 degrees sample). The experimental results show that the yield stress of the 0 degrees sample is the highest, while the 45 degrees sample is the lowest. Compared with other samples, the 90 degrees sample is more sensitive to the applied strain rate, which experiences a rapid failure after reaching peak stress under high-speed impact. Under quasi-static compression and high-speed impact, the 0 degrees sample exhibits nearly uniform deformation, while the 45 degrees and 90 degrees samples exhibit anisotropy behavior. Due to the occurrence of adiabatic shear, the plastic deformation anisotropy in 45 degrees and 90 degrees samples under high-speed impact is more significant compared to quasi-static compression. For the 45 degrees and 90 degrees samples, the r values, which characterize plastic deformation anisotropy, decrease from 0.77 to 0.82 under quasi-static compression to 0.46 and 0.40 under high-speed impact. In addition, adiabatic shear bands are observed in all deformed samples under highspeed impact, while only the 90 degrees sample fractures. Due to the significant difference in Schmidt factors along ED and transverse direction (TD), plastic deformation of the 90 degrees sample under high-speed impact is mainly concentrated in TD, while the deformation in ED is very small. The extremely uneven deformation leads to earlier nucleation and faster development of ASBs in TD, causing the 90 degrees sample to fracture under high-speed impact.

Anisotropic Behavior of As-Extruded 7003 Aluminum Alloy under Quasi-Static Compression and High-Speed Impact

Anisotropic Deformation Behavior of As-Extruded 6063-T4 Alloy under Dynamic Impact Loading

Unveiling the Initiation and Evolution Mechanisms of Adiabatic Shear Band in Extruded 7003 Aluminum Alloy under High-Speed Impact Load

Effect of Extrusion Ratio on Mechanical Behavior and Microstructure Evolution of 7003 Aluminum Alloy at High-Speed Impact

The Deformation Mechanism and Adiabatic Shearing Behavior of Extruded Mg-8.0Al-0.1Mn Alloy in Different Heat Treated States under High-Speed Impact Load

High-Speed Impact Behavior and Microstructure Evolution of an Extruded Mg-7Sn-5Zn-3Al Alloy

Microstructural Evolutions of AA7055 Aluminum Alloy under Dynamic and Quasi-static Compressions

Anisotropic Low Cycle Behavior of the Extruded 7075 Al Alloy

Effect of deformation condition on plastic anisotropy of as-rolled 7050 aluminum alloy plate

Anisotropy and Asymmetry of As-Extruded AZ31 Magnesium Alloy Deformed under High Strain Rate

Distribution Characterization of Boundary Misorientation Angle of 7050 Aluminum Alloy after High-Temperature Compression

Anisotropy and Deformation Mechanisms ofAs-Extruded Mg-3Zn-1Y Magnesium AlloyUnder High Strain Rates

Flow Behavior and Microstructure Evolution of 7055 Aluminum Alloy Impacted at High Strain Rates

Characterization of Anisotropic Fracture Behavior of 7075-T6 Aluminum Alloy Sheet under Various Stress States

Anisotropic Microstructure and Thixo-Compression Deformation Behavior of Extruded 7075 Aluminum Alloy in Semi-Solid State

A Study on the Dynamic Mechanical Behavior and Microtexture of 6082 Aluminum Alloy under Different Direction

Flow and Fracture Behavior of Aluminum Alloy 6082-T6 at Different Tensile Strain Rates and Triaxialities

Prediction of Flow Stress and Characterizing the Deformation Mechanism of As‐extruded 7005 Aluminum Alloy

Investigation of the mechanisms on the abnormal features observed in thermal-mechanical testing of AA6061 under extrusion conditions

Anisotropic Behavior in Plasticity and Ductile Fracture of an Aluminum Alloy

Abnormal Twinning Behavior and Constitutive Modeling of a Fine-Grained Extruded Mg–8.0Al–0.1Mn–2.0Ca Alloy under High-Speed Impact along Various Directions