Abstract:Wire arc additive manufacturing (WAAM) technology has potential advantages in the production of large-scale aluminum alloy components. However, as-deposited Al–Cu alloys produced by WAAM often suffer from porosity defects and coarse eutectic phases distributed along the grain boundaries, resulting in poor mechanical properties and hindering the applicability of WAAM to prepare aluminum alloy components. Herein, 2219 aluminum alloy was prepared using WAAM assisted by interlayer friction stir processing (FSP). Porosity defects in the as-deposited materials were eliminated, and coarse eutectic phases were broken and dissolved into the α-Al matrix via interlayer FSP, improving the mechanical properties of the components. The specimens processed by WAAM + interlayer FSP were subjected to different thermal cycling at different locations. The top-layer stir zone (SZ) was not affected by thermal cycling during the additive manufacturing process, and mechanical properties in the SZ were superior to those in the middle region. Compared with the as-deposited materials prepared by WAAM, the yield strength (YS) and ultimate tensile strength (UTS) in the middle region along the horizontal direction of the components manufactured by WAAM + interlayer FSP increased from 118 to 143 MPa and from 255 to 277 MPa, respectively. Further, the ultimate fatigue strength increased from 97 to 139 MPa. The YS and UTS along the vertical direction were 140 and 268 MPa, respectively, which are slightly lower than those along the horizontal direction. This is due to the small overlapping between the two adjacent SZs. The partially melted zone (PMZ) between the SZs was not completely eliminated, and the θ phase in the PMZ was mostly distributed along the grain boundaries.

Improving Comprehensive Properties of Wire Arc Additively Manufactured Al-4043 Alloy by Bilateral Friction Stir Post-processing

Improvement of microstructure and fatigue performance of wire-arc additive manufactured 4043 aluminum alloy assisted by interlayer friction stir processing

Microstructure refinement and mechanical properties enhancement of wire and arc additively manufactured 6061 aluminum alloy using friction stir processing post-treatment

Enhanced High-Temperature Strength and Ductility of Wire Arc Additive Manufactured Al-Ce-Mg Alloys with Fine Α-Al/al11ce3 Eutectics

Microstructure refinement and mechanical properties enhancement of wire-arc additive manufactured 2219 aluminum alloy assisted by interlayer friction stir processing

Impact of Process Parameters on Forming Quality and Deposition Efficiency of Unsupported Rods in Wire Arc Additive Manufacturing

Microstructural modification and enhanced mechanical properties of wire-arc additive manufactured 6061 aluminum alloy via interlayer friction stir processing

Evolution of microstructure and properties in 2219 aluminum alloy produced by wire arc additive manufacturing assisted by interlayer friction stir processing

Tailoring the microstructure and mechanical properties of wire and arc additive manufactured Al-Mg alloy via interlayer friction stir processing

Microstructure evolution and mechanical properties of wire-arc additive manufactured Al–Zn–Mg–Cu alloy assisted by interlayer friction stir processing

Enhanced strength-plasticity of 2319 Al-Cu alloy formed by hybrid interlayer friction stir processing and wire-arc additive manufacturing

Achieving high strength-ductility properties of wire-arc additive manufactured Al-Mg-Sc aluminum alloy via friction stir processing post-treatment and high temperature aging treatment

Microstructure Evolution and Grain Refinement in 2319 Aluminium Alloy Via Wire Arc Additive Manufacturing Coupled with Multi-Pass Friction Stir Processing

Achieving high strength and fatigue performance of wire-arc additive manufactured 6061 aluminum alloy via interlayer friction stir processing and heat treatment

Improving mechanical properties of wire arc additively manufactured AA2196 Al–Li alloy by controlling solidification defects

Improved material properties of wire arc additively manufactured Al-Zn-mg-cu alloy through severe deformation interlayer friction stir processing and post-deposition heat treatment

Enhancing mechanical properties and defects elimination in 2024 aluminum alloy through interlayer friction stir processing in wire arc additive manufacturing

Microstructure Evolution of Wire-Arc Additively Manufactured 2319 Aluminum Alloy with Interlayer Hammering

Enhancing strength, ductility, and fatigue performance of Al-Zn-Mg-Cu-Sc-Zr alloy using a hybrid approach: Wire-arc directed energy deposition and interlayer friction stir processing

Minimizing porosity and optimizing microstructure of hot-wire arc additive manufactured Al-Cu-Mg-Ag alloy for strength increment

Comparative Study on Wire-Arc Additive Manufacturing and Conventional Casting of Al–Si Alloys: Porosity, Microstructure and Mechanical Property