Abstract:Some biological surfaces were proved to have excellent anti-wear performance. Being inspired, Nd:YAG pulsed laser was used to create striated biomimetic laser hardening tracks on medium carbon steel samples. Dry sliding wear tests biomimetic samples were performed to investigate specific influence of distribution of laser hardening tracks on sliding wear resistance of biomimetic samples. After comparing wear weight loss of biomimetic samples, quenched sample and untreated sample, it can be suggested that the sample covered with dense laser tracks (3.5 mm spacing) has lower wear weight loss than the one covered with sparse laser tracks (4.5 mm spacing); samples distributed with only dense laser tracks or sparse laser tracks (even distribution) were proved to have better wear resistance than samples distributed with both dense and sparse tracks (uneven distribution). Wear mechanisms indicate that laser track and exposed substrate of biomimetic sample can be regarded as hard zone and soft zone respectively. Inconsecutive striated hard regions, on the one hand, can disperse load into small branches, on the other hand, will hinder sliding abrasives during wear. Soft regions with small range are beneficial in consuming mechanical energy and storing lubricative oxides, however, soft zone with large width (>0.5 mm) will be harmful to abrasion resistance of biomimetic sample because damages and material loss are more obvious on surface of soft phase. As for the reason why samples with even distributed bionic laser tracks have better wear resistance, it can be explained by the fact that even distributed laser hardening tracks can inhibit severe worn of local regions, thus sliding process can be more stable and wear extent can be alleviated as well. (C) 2017 Elsevier Ltd. All rights reserved.

Hard-soft Biomimetic Structure Distribution Enhanced Wear Resistance of AISI1045 Steel by Laser Processing

Influence of processing medium on frictional wear properties of ball bearing steel prepared by laser surface melting coupled with bionic principles

Effect of Distribution of Striated Laser Hardening Tracks on Dry Sliding Wear Resistance of Biomimetic Surface

Effects of Laser-Processed Unit Distribution Density on Wear Resistance of Biomimetic 6082 Aluminum Alloy

Effect of Composition on the Mechanical Properties and Wear Resistance of Low and Medium Carbon Steels with a Biomimetic Non-Smooth Surface Processed by Laser Remelting

Study on the Relationship Between Intervals among Laser Stripes and the Abrasion Resistance of Biomimetic Laser Textured Surfaces

Hardness Difference Effect of Biomimetic Surface with Hard-Soft Structure on Oil - Lubrication Wear Resistance

Wear Behavior Of Medium-Carbon Steel With Different Laser-Textured Densities Under Starved Lubrication

Wear properties of H13 with micron scale and nano scale grains bionic units processed by laser remelting

Bio-inspired Wearable Characteristic Surface: Wear Behavior of Cast Iron with Biomimetic Units Processed by Laser

Wear Behavior of Quenched Iron with Various Shapes and Unit Processed Through Two-Step Laser Alloying of C Powder

Influence of Laser Energy Density on Acquisition and Wear Resistance of Bionic Semisolid Unit of 40cr Steel

Fabrication of Wear-Resistant Layers with Lamellar Eutectic Structure by Laser Surface Alloying Using the in Situ Reaction Between Cr and B 4 C

Wear Behavior of Medium Carbon Steel with Biomimetic Surface under Starved Lubricated Conditions

The Mechanical Properties of Medium Carbon Steel Processed by A Biomimetic Laser Technique

Micromorphology, Microstructure, and Wear Behavior of AISI 1045 Steels Irregular Texture Fabricated by Ultrasonic Strengthening Grinding Process

Lubricating Property of Cast Iron Combined with Two-Scale Unit Structure by Biomimetic Laser Treatment

Mechanical Property of a Low Carbon Steel with Biomimetic Units in Different Shapes

Effect of Dual Hardness Combinations on Wear Resistance of Laser Prepared Bionic Grey Iron Surfaces.Effect of Dual Hardness Combinations on Wear Resistance of Laser Prepared Bionic Grey Iron Surfaces

Study on laser prepared reinforcement unit distribution of large scale non-uniform hardness surface of gray cast iron against wear

Tribological properties of soft/hard hybrid surface of Babbitt alloy/steel