Application of a coal combustion model in the design of blast parameters for an ironmaking blast furnace
D. MALDONADO,P. ZULLI,Y. S. SHEN,B. Y. GUO,YU A.B.
2006-01-01
Abstract:With significant economic drivers to reduce consumption of expensive coking coal, Pulverized Coal Injection (PCI) commenced at BlueScope Steel in 2002, at injection rates ranging between 100 and 150 kg-coal/tonne of liquid iron. The key limitation to injection rates is associated with the reduction in packed bed permeability via additional char load into the furnace. The coal is injected via a simple coaxial lance, consisting of an inner pipe (for coal and carrier gas) and an outer annulus (for cooling gas to protect the lance from the high furnace temperatures). The cooling gas can be compressed air, natural gas or pure oxygen. Depending on the choice of cooling gas, the oxygen-to-carbon ratio of the system will change. In this paper, the application of a validated three-dimensional numerical model of the blowpipe/tuyere/raceway is described. The model is used for various plant-specific investigations of blast parameters such as oxygen enrichment, blast temperature and atomic oxygen-tocarbon ratio. The model results show the sensitivity of coal burnout to different operating parameters and confirm that burnouts higher than 80% are difficult to obtain due to the short residence times of the coal. NOMENCLATURE A Arrhenius rate constant B Coal burnout CD Gas-solid drag coefficient dp Particle diameter e Char particle void fraction k1 Boundary layer diffusion (Gibb equation) k2 Surface reaction rate (Gibb equation) k3 Internal diffusion rate (Gibb equation) ma Ash mass fraction ma,0 Original ash mass fraction MC Molecular weight of carbon Mo2 Molecular weight of oxygen molecule Nu Nusselt number Pr Prandtl number Re Reynolds number Tc Activation temperature (K) Tp Particle temperature (K) εp Particle emissivity φ Molar ratio (Gibb equation) ρ Density σ Stefan-Boltzmann constant INTRODUCTION Pulverised coal injection was introduced at BlueScope Steel’s Port Kembla blast furnaces (BF) in 2002, with aim injection rates in the range of 100-150 kg-coal/tonne of liquid iron. Due to recent changes in supply coal pricing structure, there is a clear economic advantage associated with increasing PCI rates to replace coking coal. Overseas experience, eg from European steelmakers such as Corus IJmuiden and Arcelor Sidmar, suggest that coal injection rates up to and in excess of 200 kg-coal/tonne of liquid iron are sustainable. Combustion of coal under blast furnace conditions differs from the combustion phenomena experienced in coal fired power stations because of the differences in air temperature, air flow rate, oxygen enrichment and nozzle geometry. Modelling of coal combustion under blast furnace conditions is relatively well advanced (Ishii, 2000). One of the key factors affecting the maximum PCI rate attainable at the BF is the packed bed permeability – a more permeable bed is more able to cope with the additional char load. In order to minimise char load, the extent of coal combustion (burnout) within the inlet nozzle (tuyere) and raceway must be optimised. This can be achieved through improvements in a) lance design, eg double eccentric lances and/or lance tip shape, b) injection air (blast) parameters, eg oxygen enrichment, cooling gas type, and c) coal type. Recently, BlueScope Steel Research and University of NSW jointly developed a three-dimensional numerical model to describe the flow and combustion of pulverised coal under BF conditions (Guo et al., 2005). The model was based on the geometry of, and flow conditions used in, BHP Billiton’s “third generation” combustion test rig, located at its Newcastle Technology Centre (Mathieson et al., 2003). The original version of the model was developed using the commercial CFD package CFX ver4.4. More recently, a new version of CFX, ver10 (ANSYS CFX, 2006), has been released with an improved coal combustion sub-model within its solver architecture. In addition, the previous version of the model was relatively insensitive to atomic oxygen to carbon (O/C) ratios. This has been addressed by introducing the partial oxidation of char (carbon) to CO, as well as the gasification reactions of char with CO2 and H2O. Homogeneous gas phase oxidation reactions of CO and H2 are also introduced.