Abstract:Sintering behaviour of ashes from combustion of coal and biomass blends was experimentally investigated with a focus on the effect of ash preparation method. Blends of a Chinese anthracite, Jincheng coal, and two biomass materials, a wheat straw and a pine sawdust, respectively, were subjected to three different ash preparation procedures, namely, a low temperature oxygen plasma ashing device operating at ca 150 degrees C, combustion in a Muffle furnace at 815 degrees C and in a drop tube furnace at 1500 degrees C. The resulting ash samples were then subjected to the sintering temperature measurement using a pressure-drop sintering device, morphological and mineralogical characterisation using scanning electron microscope (SEM) fitted with X-ray energy dispersive spectroscopy (EDS) and X-ray diffractometry analyser (XRD), respectively. For the same coal and biomass blends but different ash preparation methods, the sintering temperatures were always the lowest for the ash samples from the plasma ashing device and the highest from drop tube furnace. SEM imaging showed that the texture of ash samples from the plasma ashing device was irregular, loose and more fibrous, indicating little interactions among the different mineral and inorganic constituents in the individual fuels. The muffle furnace and drop tube furnace ashes were denser and more uniform in shape as the mineral matter and inorganics became fused together. In addition, the drop tube furnace ashes were mostly in spherical-shape, indicating ash melting had occurred during combustion. The XRD analysis revealed that different minerals were present in the ash samples due to different ash preparation temperatures, with high temperature minerals present in the drop tube furnace ash. Biomass addition in the blends lowered the sintering temperature of corresponding ash; the higher the proportion of biomass in the blend, the lower the ash sintering temperature regardless the ashing method. At the same biomass addition ratio, the ash sintering temperature of the blend with the wheat straw addition was lower than that with the pine sawdust addition, because the wheat straw had a higher K and Cl content but lower Ca than the pine sawdust. The EDS and XRD analyses confirmed that the ashes of coal/wheat straw blends contained more K-bearing minerals, while the ashes of the coal/pine sawdust contained more Ca and K-bearing minerals. Both Ca and K-bearing minerals reacted with other minerals in the ash to form low temperature eutectics, leading to the reduction of sintering temperatures of the coal and biomass blends. However, the melting points of the K-containing minerals are higher than the Ca-containing minerals, therefore, the sintering temperatures of ash with the wheat straw addition were lower than those with the pine sawdust addition. (C) 2016 Elsevier Ltd. All rights reserved.

Optimizing Combustion Efficiency in Blast Furnace Injection: A Sustainable Approach Using Biomass Char and Coal Mixtures

Study on the feasibility and co-combustion mechanism of mixed injection of biomass hydrochar and anthracite in blast furnace

Non-isothermal Thermogravimetric Investigation on Mutual Effect Between Bituminite and Anthracite in Blends for Blast Furnace Injection

Comprehensive Study on the Feasibility of Pyrolysis Biomass Char Applied to Blast Furnace Injection and Tuyere Simulation Combustion

Co-combustion kinetic analysis of biomass hydrochar and anthracite in blast furnace injection

Kinetic Study on Co-Combustion of Pulverized Anthracite and Bituminite for Blast Furnace Injection

Calculation on effective heat of injected pulverized coal in blast furnace

Experiment research on utilization of particle biomass fuel in sintering process

Effect of Ash Preparation Method on the Sintering Characteristics of Ashes from Combustion of Coal and Biomass Blends

Feasibility Analysis of Biomass Hydrochar Blended Coal Injection for Blast Furnace

The Thermal Behavior and Kinetics of Co-Combustion Between Sewage Sludge and Wheat Straw

Co-injection of hydrogen and biochar (CoHB) in a simulated blast furnace: A univariate and multivariate study

The Combustion of Forest Humus Blended with Low-Rank Coal: Effects of Oxygen Ratio and Blending Ratio

Numerical investigation of hydrogen-rich gas and pulverized coal injection in the raceway of a blast furnace with lower carbon emissions

Combustion behavior of co-injecting flux, pulverized coal, and natural gas in blast furnace and its influence on blast furnace smelting

Numerical simulation study on the effects of co-injection of pulverized coal and SPL (Spent Pot-Lining) into the blast furnace

A Complex Evaluation and Optimization Approach for Oxygen-Enriched Combustion Characteristics of Blended Fuels Based on Response Surface Methodology

Investigation on co-combustion of coal gasification fine slag residual carbon and sawdust char blends: Physiochemical properties, combustion characteristic and kinetic behavior

An evaluation on rice husks and pulverized coal blends using a drop tube furnace and a thermogravimetric analyzer for application to a blast furnace

Reduced Pollutant Emissions and Slagging Rate of Biomass Pellet Combustion by Optimizing the Multilayer Distribution of Secondary Air

Thermodynamics and synergistic effects on the co-combustion of coal and biomass blends