Abstract:Recently, energy conservation, environmental protection and security are the main factors considered by the automotive manufacturers. Medium-Mn steel with excellent combination of specific strength and ductility have been regarded as the potential candidates for automotive applications. The excellent combination of specific strength and ductility depends on the microstructure under different heat treatment processes of the steels. Therefore, the relationship of the combination of specific strength and ductility and microstructure should be studied in detail. Anew alloy system of aluminum-containing medium-Mn steel was developed in this study. The addition of aluminum stabilizes alpha-ferrite, and facilitates the presence of 6-ferrite during solidification. The addition of Mn and C compensates the effect of aluminum on phase stability and ensures austenite formation. In this investigation, the effects of intercritical annealing temperature on the microstructure and tensile properties of a newly designed cold-rolled aluminum-containing medium-Mn steel (0.2C-5Mn- 0.6Si- 3Al, mass fraction, %) were investigated by SEM, XRD and uniaxial tensile tests. The tensile results show that an excellent combination of ultimate tensile strength (sigma(b)) of 1062 MPa, total elongation (delta) of 58.2% and sigma(b) x delta of 61.8.% could be obtained after annealing at 730 degrees C. The inverted austenite of the cold-rolled steel coarsenes and gradually changes its morphology from mainly lamellar to mainly equiaxed with increasing intercritical annealing temperature, and a duplex microstructure consisting of multi-scale retained austenite could be obtained at 730 degrees C, which possesses suitable mechanical stability and thus presents prolonged transformation-induced plasticity (TRIP) effect during tensile deformation. This kind of sustainable TRIP effect and the cooperative deformation of ferrite are responsible for the superior mechanical properties. The investigation of tensile fracture behavior shows that the nucleation and growth of voids occurred mainly at the interfaces between soft ferrite and hard martensite induced by deformation.

Quantitative Analysis of Yield Strength in V-Alloying Medium Manganese Steel under Different Processes

Influence of Thermo-Mechanical Process and Nb-V Microalloying on Microstructure and Mechanical Properties of Fe–Mn–Al–C Austenitic Steel

Multiphase precipitation and its strengthening mechanism in a V-containing austenite-based low density steel

Effects of Vanadium Microalloying and Intercritical Annealing on Yield Strength–Ductility Trade-Offs of Medium-Manganese Steels

Modeling Microstructure and Yield Strength during Solidification and Heat Treatment Process in Al-7Si-Mg Cast Aluminum Alloys

Multiphase precipitation behavior and tensile properties of a Fe-Mn-Al-Mo-C austenitic lightweight steel

Influence Of Al And C On Mechanical Properties Of Sub-Rapidly Solidified Fe-20mn-Xal-Yc Low-Density Steels

Enhancing Yield Strength and Ductility of Fe-Mn-C-xAl (x = 0, 3) High Manganese Steel by Cryogenic Rolling

Super-High-Strength and Formable Medium Mn Steel Manufactured by Warm Rolling Process

Microstructure evolution and tensile behaviour of a cold rolled 8 wt\% Mn medium manganese steel

Thermal deformation behavior and microstructure evolution of Fe−8.5Mn−1.5Al light−weight medium manganese steel

Microstructural characteristics and tensile behavior of medium manganese steels with different manganese additions

Microstructural Evolution and Mechanical Properties of V-Containing Medium-Mn Steel Adopting Simple Intercritical Annealing

Heterogeneous Multi-Phase Grains Improving the Strength-Ductility Balance in Warm-Rolled Fe-18Mn-3Ti Steel

Yielding Behavior and Strengthening Mechanisms of a High Strength Ultrafine‐Grained Cr–Mn–Ni–N Stainless Steel

Effects of annealing temperature and V addition on microstructure and mechanical properties of Fe-Mn-Al-C austenitic low-density steel

Tailoring retained austenite and mechanical property improvement in Al–Si–V containing medium Mn steel via direct intercritical rolling

Achieving high strength and ductility in Fe-Mn-Al-C austenitic steel via vanadium microalloying and aging

Microstructure and Mechanical Properties of a Novel Cold Rolled Medium-Mn Steel with Superior Strength and Ductility

Influence of ε-martensite and austenite on mechanical properties by intercritical annealing in 0.1C-11Mn medium manganese steel

Effect of C and Mn element partitioning behavior on microstructure and properties of cold-rolled medium manganese TRIP steel