Abstract:The Ni-Fe-based superalloy GH4169 (Inconel718) is widely used for several critical gas-turbine components which are hot forged. Its microstructure and property are sensitive to the parameter adjustment during hot working process. To obtain required low-cycle fatigue and fracture properties, it is essential that the microstructure is controlled during preheating and heat treatment. The evolution of non-uniform microstructure during hot working is more complicated than that of uniform microstructure. On the other hand, various secondary phases can be observed in GH4169 alloy, thus it is important to investigate the effect of secondary phases on the microstructure evolution during forging process. In this work, the mechanisms of non-uniform microstructure evolution in GH4169 alloy were studied by analyzing the evolution of secondary phases, grain boundary misorientation, grain size and interactions of dislocation. It is found that the volume fraction of 8 phase increases with the increasing of temperature and heating time at the lower temperature. While at the higher temperature, it decreases monotonously with the temperature increasing, but increases first and then decreases to stable value with time increasing. The pinning effect of secondary phases in GH4169 alloy can be concluded that the gamma '' phase and 8 phase precipitated within the grains retain movement of dislocation, the 8 phase precipitated at the grain boundary hinders the nucleation and growth of recrystallized grains, and the carbides limits the grain growth. The frequency of low angle grain boundary decreases with temperature and time increasing, and the mobility of low angle grain boundary increases with temperature increasing. The uniformity of microstructure and the size of equaxied subgrain increases with heating temperature and time increasing. Continuous recrystallization of elongated grain occurs at specific conditions. The mechanisms of non-uniform microstructure evolution during heating process can be concluded as sub grain growth, recrystallized grain growth, and anneal twinning nucleation and growth. The recrystallized grains are formed by the growth of subgrains conducted by the rotation of low angle grain boundary and the movement of dislocation. When the grain growth is pinned, the mechanisms for the energy dissipation is the nucleation and growth of anneal twinning. And the growth of anneal twinning promotes the generation of low angle grain boundaries at the tip of partial anneal twinning.

Quasi-in-Situ Observation and Analysis of Grain Boundary Evolution of Gh4169 Nickel-Based Superalloy During Micro-Strain Stage of Thermal Deformation

Quasi-in-situ Observation and Analysis of Grain Boundary Evolution of GH4169 Nickel-Based Superalloy During the Micro-Strain Stage of Thermal Deformation

Mechanisms of Non-Uniform Microstructure Evolution in Gh4169 Alloy During Heating Process

Molecular Dynamics Simulation of Dislocation and Phase Transition for Ni-Based Superalloys with Twist Grain Boundary

EBSD Study of Strain Dependent Microstructure Evolution During Hot Deformation of a Typical Nickel-Based Superalloy

In-situ Observation of Ni-Co Based Wrought Superalloy High-Temperature Deformation: Lattice Rotation and Grain Boundary Response

Microstructure and Microtexture Evolution of Dynamic Recrystallization of a Ni-based Superalloy under High-Throughput Gradient Thermal Compression

Damage Tolerance of Low Angle Grain Boundary in a Fourth Generation Nickel-based Single Crystal Superalloy at 1100 °C Service Conditions

Microstructure evolution and dynamic recrystallization mechanism during thermal deformation of GH4698 superalloy

Influencing Mechanisms of Prior Cold Deformation on Mixed Grain Boundary Network in the Thermal Deformation of Ni80A Superalloy

Grain Boundary Engineering of a Low Stacking Fault Energy Ni-based Superalloy

In Situ Study of the Microstructural Evolution of Nickel-Based Superalloys with High Proportional Twin Boundaries Obtained by High-Temperature Annealing

Evolution of Grain Boundary Character Distributions in a Cold-Deformed Nickel-based Superalloy During Electropulsing Treatment

Study on Grain Boundary Characteristic Distribution of Nickel Base 625 Alloy Controlled by Deformation Heat-Treatment Process

In Situ Study of the Microstructural Evolution of Nickel-Based Alloy with High Proportional Twin Boundaries Obtained by High-Temperature Annealing.

Microstructure Evolution and Dynamic Softening Mechanisms During High-Temperature Deformation of a Precipitate Hardening Ni-based Superalloy

In-situ EBSD study of deformation behavior of nickel-based superalloys during uniaxial tensile tests

Orientation-Dependent Characteristics for Residual Grains During Hot Deformation of Nickel-Based Alloy 925

Evolution mechanisms of recrystallized grains and twins during isothermal compression and subsequent solution treatment of GH4586 superalloy

Improve the ductility of a nickel based superalloy by optimizing secondary phase distribution through grain boundary engineering

Strain Amount Dependent Grain Size And Orientation Developments During Hot Compression Of A Polycrystalline Nickel Based Superalloy