Abstract:Currently, many utility‐scale wind turbine generator original equipment manufacturers are dependent on imported rare earth permanent magnets, which are susceptible to market risks from cost instability. To lower the production costs of these generators and stay competitive in the market, several small wind manufacturers are pursuing continuous improvements to both generator design and manufacturing. However, traditional design and manufacturing methods have yielded marginal improvements in wind power performance. This work presents novel methods to redesign a baseline 15‐kW wind turbine generator with reduced rare‐earth permanent magnets by leveraging cutting‐edge three‐dimensional (3D) printed polymer‐bonded permanent magnets and steel. Symmetric, asymmetric, and multimaterial‐magnet parametrization methods are introduced for shape optimization. We extend the symmetric and asymmetric methods to the back iron in the stator to further investigate the impact and opportunities for performance improvements with lesser active materials. We employ a design‐of‐experiments approach with parametric computer‐aided design for shape generation and evaluate different designs by magneto‐thermal modeling and finite‐element analysis. We use adaptive sampling technique to identify better performing designs with lesser magnet mass, higher efficiency, and lower cogging torque when compared with the baseline generator. Asymmetric pole designs resulted in a magnet mass in the range of 4.77–5.37 kg, which was 27%–35% lighter than the baseline generator, suggesting that a new design freedom exists that can be enabled by advanced manufacturing, such as 3D printing. Shaping the back iron in the stator resulted in material savings in electrical steel of up to 14.62 kg, which was 20% lighter than the baseline stator. We conducted a structural analysis to evaluate an optimized asymmetric rotor design from the point of view of mechanical integrity and air‐gap stiffness. The magnetically optimal shape profile was shown as having a positive impact on the radial stiffness, and an optimal solution was discovered to reduce the structural mass by nearly 30 kg, which was 29% lighter than the baseline.

Developing Stator and Rotor Windings of Low-Voltage Alternators with Improved Lifetime Using Tailored Polyester Nanocomposites

Fabrication and test results of low‐voltage alternator with improved efficiency and reduced temperature rise using polyester nanocomposite insulation

Mille-Feuille Inspired Thermally Conductive Polymer Nanocomposites with Overlapping BN Nanosheets for Thermal Management Applications.

Advanced multimaterial shape optimization methods as applied to advanced manufacturing of wind turbine generators

Study on thermal cycling ageing resistance of performances of polypropylene/elastomer/boron nitride nanocomposites for high voltage direct current cable insulation

A Novel Auxetic Stator Winding to Improve the Performance of Permanent Magnet Synchronous Electric Motors

Tuning Phase Composition of Polymer Nanocomposites towards High Energy Density and High Discharge Efficiency by Non-Equilibrium Processing.

Experimental and Computational Study of Mechanical and Thermal Characteristics of h-BN and GNP Infused Polymer Composites for Elevated Temperature Applications

Numerical Simulation of Heat Transfer Characteristic of Aluminum Nitride (AlN) Potting Compound for the End Windings of Permanent Magnet Synchronous Machines with Experimental Verification

Superhydrophobic Yet Highly Thermally Conductive BN Composites for Electrical Erosion Resistance

Lifetime Model for Inverter-fed Electrical Machines Windings Including Thermal Aging and Partial Discharge Risk

Application of Soft Magnetic Composite in XEV Motor Core Manufacturing: Process Effects and Performance Analysis

Novel Engineered Materials: Epoxy Resin Nanocomposite Reinforced with Modified Epoxidized Natural Rubber and Fibers for Low Speed Wind Turbine Blades

Insulation for Rotating Low-Voltage Electrical Machines: Degradation, Lifetime Modeling, and Accelerated Aging Tests

Poly(vinyl Alcohol)-Assisted Exfoliation and Grafting Modification of Boron Nitride Nanosheets with a High Aspect Ratio Via a Continuous Production Method for Energy Storage and Thermal Management.

Life Characterization of PEEK and Nanofilled Enamel Insulated Wires Under Thermal Ageing

Layers-to-layers assembled graphene-boron nitride for polymer composites with enhanced thermal stability and dielectric constant at low loss

Sandwich-structural PVDF Nanocomposites with High Thermal Conductivity and Excellent Dielectric Properties

Windings Indirect Liquid Cooling Method for a Compact Outer-Rotor PM Starter/Generator With Concentrated Windings

One-step alkyl-modification on boron nitride nanosheets for polypropylene nanocomposites with enhanced thermal conductivity and ultra-low dielectric loss

Sandwich-structured polymers with electrospun boron nitrides layers as high-temperature energy storage dielectrics