Abstract:Comprehensive Summary Recently, hybrid organic–inorganic perovskite materials have drawn widespread attention because of their outstanding optoelectrical properties (i.e., high absorption coefficient, long carrier diffusion distance), hence they are suitable light‐absorbing materials for photovoltaic application. Among all perovskite materials, formamidinium lead iodide (FAPbI3) based solar cells exhibit impressive power conversion efficiency (PCE) at laboratory stage, showing great potential to compete with silicon‐based solar cell. However, FAPbI3 still suffers from poor phase stability which is the prior problem that needs to be addressed before its further commercialization. To be precise, the photoactive phase (α phase) is thermodynamically metastable at room temperature, which not only makes α phase tend to transform into photoinactive phase (δ phase), but also causes competitive crystallization between two phases during the film preparation process, making it hard to fabricate pure α‐FAPbI3 films. In our review, we summarized key factors that are vital for obtaining high‐quality FAPbI3 perovskite thin films and enhancing the stability of FAPbI3 photoactive phase. First of all, precursor solution stability is of great importance since the conditions of precursor solution determine the nucleation and crystal growth process of perovskite. By introducing coordinating additives, using FAPbI3 single crystal as raw material or applying co‐solution strategy, the impurities formed by side reaction during precursor solution aging can be effectively suppressed, thus the stability of FAPbI3 solution can be greatly prolonged. Second, the crystallization kinetics of FAPbI3 have been systematically manipulated to obtain dense and large grain size perovskite films. Through introducing intermediate phase, regulating the surface energy, and retarding the crystal growth of FAPbI3 in crystallization process, not only films without pinholes and fewer grain boundaries can be obtained, the pre‐formed δ phase at room temperature can also be well‐suppressed, thus high‐quality α‐FAPbI3 films can be obtained. Third, how to thermodynamically enhance the phase stability of acquired FAPbI3 film has been extensively studied. The Gibbs free energy of FAPbI3 photoactive phase can be reduced through composition engineering, dimension engineering and external additives engineering, hence the phase transition barrier from α phase to δ phase has been significantly improved, which further enhance the phase stability of α‐ FAPbI3. Lastly, we pointed out challenges of each method and proposed potential applications of mentioned strategies on improving the stability of all kinds of perovskite materials, thus further boost the commercialization of perovskite solar cell devices. This article is protected by copyright. All rights reserved.

Crystallization Dynamics and Stabilization of FAPbI3 Single-Phase Perovskite

Crystallization and stabilization of FAPbI3 single-phase perovskite

Stabilizing FASnI3-based Perovskite Light-Emitting Diodes with Crystallization Control

Phase Stabilization for High-Performance Perovskite Light-Emitting Diodes

Soft Lattice and Phase Stability of α‐FAPbI3

Significantly Improved Black Phase Stability of FAPbI3 Nanowires Via Spatially Confined Vapor Phase Growth in Nanoporous Templates.

Phase‐Transition‐Cycle‐Induced Recrystallization of FAPbI3 Film in An Open Environment Toward Excellent Photodetectors with High Reproducibility

Advances to Stabilize Photoactive Phase of FAPbI3 Perovskite

Revealing phase evolution mechanism for stabilizing formamidinium-based lead halide perovskites by a key intermediate phase

Toward stabilization of formamidinium lead iodide perovskites by defect control and composition engineering

Surface Ligand Management for Stable FAPbI3 Perovskite Quantum Dot Solar Cells

Additive‐Free, Low‐Temperature Crystallization of Stable α‐FAPbI 3 Perovskite

In Situ Study of Purified Phase Transition Path for Α‐fapbi3 Crystallization

Study on the stability of organic–inorganic perovskite solar cell materials based on first principle

Stabilizing α-Phase FAPbI 3 Perovskite Induced by an Ordered Solvated Quasi-Crystalline PbI 2

Stabilization of FAPbI3 with Multifunctional Alkali‐Functionalized Polymer

Synergetic Electrostatic and Steric Effects in α‐FAPbI3 Single Crystals For X‐Ray Detection and Imaging

A Self-Assembled 3D/0D Quasi-Core-Shell Structure As Internal Encapsulation Layer for Stable and Efficient FAPbI3 Perovskite Solar Cells and Modules

Improvement in the stability of -CsPbI<sub>3</sub> nanowires enabled by lattice immobilization through the Pb-O anchor in SBA-15

Influence of Temperature, Pressure and Humidity on the Stabilities and Transitions Kinetics of the Various Polymorphs of FAPbI$_3$

A crystal capping layer for formation of black-phase FAPbI 3 perovskite in humid air