Abstract:Organic additives used in Cu electroplating for IC interconnects have been studied extensively due to their pivotal roles in the void-free filling of recessed features. The suppressive additives are typically polymers or co-polymers with variable molecular weight (MW). The properties of these additives, as well as their interaction with accelerator, vary with the monomer type and the MW. As the additives are typically treated as indivisible molecules in the analysis of the filling mechanism, these variations are typically quantified by the difference in some coefficients that characterize the additive behaviors, such as adsorption / desorption rates and suppression strength. As an example, polyethylene glycol (PEG) with a larger MW would have a higher adsorption rate and exhibit stronger suppression effect than PEG with a smaller MW. However, since these large molecules consist of multiple identical building blocks from the polymerization of one or more monomer species, the behavior of the molecule as a whole depends on the number and type of the monomers. In order to understand such an intrinsic dependency and the resulting differences in additive properties, stochastic modeling was applied in the study of suppressor additive and its interaction with accelerator [1]. Using PEG and SPS as the model chemicals, a stochastic model was developed to simulate the transient processes in Cu electroplating, e.g. cyclic voltammogram (CV) under various conditions. Simulations were performed for both suppressor-only cases and suppressor-accelerator interactions. The dependency of PEG adsorption / desorption and PEG-SPS interaction on various factors, including bath composition, scan rate and molecular weight, was simulated and compared with the corresponding experimental measurements. An overall good qualitative match was shown in the comparisons. Figure 1 shows simulated CVs under two very different conditions. At higher SPS/Cl - concentrations, case (a) demonstrates the PEG-SPS interaction, which has been known to be important for the super-conformal filling of trenches [2, 3]. At lower SPS / Cl - concentrations, case (b) demonstrates the critical desorption behavior of PEG as a suppressor, which has been shown to be important for the fast bottom-up type filling of high aspect ratio TSVs in damascene copper plating [4]. Since the proposed model provides a unified approach to simulate both the suppress-accelerator interaction and the critical desorption behavior of suppressors, it enables the development of general-purpose multi-scale simulation programs for the filling of various recessed features within a wide length-scale range covering both the Damascene interconnects and TSVs. References [1] L. Yang, A. Radisic, J. Deconinck, P. Vereecken, Journal of the Electrochemical Society, 161, D269(2014) [2] A. C. West, S. Mayer, J. Reid, Electrochemical and Solid-State Letters, 4, C50(2001) [3] T. P. Moffat, D. Wheeler, W. H. Huber, D. Josell, Electrochemical and Solid-State Letters, 4, C26(2001) [4] L. Yang, A. Radisic, J. Deconinck, P. Vereecken, Journal of the Electrochemical Society, 160, D3051(2013) Figure 1

Revisiting the Polyethylene Glycol-Chloride Adsorption Structure on Cu Electrode in Sulfuric Acid Solution by Wide-Frequency ATR-SEIRAS

Temperature-dependent inhibition of PEG in acid copper plating: Theoretical analysis and experiment evidence

Reaction-induced Iodine Adsorption on Cu Surfaces Facilitates Electrocatalytic CO2 Reduction.

In Situ Wide-Frequency Surface-Enhanced Infrared Absorption Spectroscopy Enables One to Decipher the Interfacial Structure of a Cu Plating Additive

Influence of polyethylene glycol inhibitors on properties of electroplated copper layer

Surface-enhanced IR spectroscopy investigation on the electro-oxidation of CO adlayer at a polycrystalline Pt film electrode in Cl−-containing HClO4

Void-free anisotropic deposition for IC interconnect with polyethylene glycol as the single additive based on uneven adsorption distribution

Adsorption Performances for Aqueous Cu(II) onto Chelating Resin Dowex M-4195: Interaction Mechanism Investigation

Alkyl-terminated PEG Suppressors for Copper Electroplating and Their Hydrophilic and Hydrophobic Properties

Adsorption of divalent heavy metal ions onto IDA-chelating resins: simulation of physicochemical structures and elucidation of interaction mechanisms.

Effect of the Molecular Weight of Polyethylene Glycol As Single Additive in Copper Deposition for Interconnect Metallization

Stochastic Modeling of Organic Additives in Cu Electroplating

Suppressing Sulfite Dimerization at a Polarized Gold Electrode/Water Solution Interface for High-Quality Gold Electrodeposition

Lifting Polyether Suppression during Cu Electrodeposition

An SERS study of the galvanostatic sequence employed for the electrochemical deposition of Copper in the fabrication of Interconnects

Effects of Anions on the Underpotential Deposition Behavior of Cu on Polycrystalline Pt

Influence of CO Adsorption on the Structure of Electric Double Layer on Cu Surface

Uncovering the Dissociative Adsorption of the Leveler Janus Green B on Cu Electrodes at the Molecular Level

On the role of halides and thiols in additive-assisted copper electroplating

Potential Routes and Mitigation Strategies for Contamination in Interfacial Specific Infrared Spectroelectrochemical Studies

Computational and experimental study of a novel L-Cysteine hydrochloride leveler for copper electroplated via fill in redistribution layers