Abstract:Organic additives used in Cu electroplating for IC interconnects have been studied extensively due to their pivotal roles in the void-free filling of recessed features. The suppressive additives are typically polymers or co-polymers with variable molecular weight (MW). The properties of these additives, as well as their interaction with accelerator, vary with the monomer type and the MW. As the additives are typically treated as indivisible molecules in the analysis of the filling mechanism, these variations are typically quantified by the difference in some coefficients that characterize the additive behaviors, such as adsorption / desorption rates and suppression strength. As an example, polyethylene glycol (PEG) with a larger MW would have a higher adsorption rate and exhibit stronger suppression effect than PEG with a smaller MW. However, since these large molecules consist of multiple identical building blocks from the polymerization of one or more monomer species, the behavior of the molecule as a whole depends on the number and type of the monomers. In order to understand such an intrinsic dependency and the resulting differences in additive properties, stochastic modeling was applied in the study of suppressor additive and its interaction with accelerator [1]. Using PEG and SPS as the model chemicals, a stochastic model was developed to simulate the transient processes in Cu electroplating, e.g. cyclic voltammogram (CV) under various conditions. Simulations were performed for both suppressor-only cases and suppressor-accelerator interactions. The dependency of PEG adsorption / desorption and PEG-SPS interaction on various factors, including bath composition, scan rate and molecular weight, was simulated and compared with the corresponding experimental measurements. An overall good qualitative match was shown in the comparisons. Figure 1 shows simulated CVs under two very different conditions. At higher SPS/Cl - concentrations, case (a) demonstrates the PEG-SPS interaction, which has been known to be important for the super-conformal filling of trenches [2, 3]. At lower SPS / Cl - concentrations, case (b) demonstrates the critical desorption behavior of PEG as a suppressor, which has been shown to be important for the fast bottom-up type filling of high aspect ratio TSVs in damascene copper plating [4]. Since the proposed model provides a unified approach to simulate both the suppress-accelerator interaction and the critical desorption behavior of suppressors, it enables the development of general-purpose multi-scale simulation programs for the filling of various recessed features within a wide length-scale range covering both the Damascene interconnects and TSVs. References [1] L. Yang, A. Radisic, J. Deconinck, P. Vereecken, Journal of the Electrochemical Society, 161, D269(2014) [2] A. C. West, S. Mayer, J. Reid, Electrochemical and Solid-State Letters, 4, C50(2001) [3] T. P. Moffat, D. Wheeler, W. H. Huber, D. Josell, Electrochemical and Solid-State Letters, 4, C26(2001) [4] L. Yang, A. Radisic, J. Deconinck, P. Vereecken, Journal of the Electrochemical Society, 160, D3051(2013) Figure 1

Void-free anisotropic deposition for IC interconnect with polyethylene glycol as the single additive based on uneven adsorption distribution

Effect of the Molecular Weight of Polyethylene Glycol As Single Additive in Copper Deposition for Interconnect Metallization

Potential-Dependence Of Additives Distribution In Copper Electrodeposition Via Filling

Influence of Electroplating Current Density on Through Silicon Via Filling

Calculation of the current density distribution of submicron copper electroplating based on uneven adsorption of poly(ethylene glycol)

Electroless Plating of Copper via a Sn-Free Process on Dielectric SiLK Surface Modified by UV-Induced Graft Copolymerization with 4-Vinylpyridine and 1-Vinylimidazole

Influence of polyethylene glycol inhibitors on properties of electroplated copper layer

Revisiting the Polyethylene Glycol-Chloride Adsorption Structure on Cu Electrode in Sulfuric Acid Solution by Wide-Frequency ATR-SEIRAS

Synergistic effects of additives on impurity residues in high-speed copper electrodeposition and voiding propensity in solder joints

Lifting Polyether Suppression during Cu Electrodeposition

A New Copper Electrodeposition Scheme to Reduce Void Defects after Chemical Mechanical Polishing

Influence of Convection-Dependent Adsorption of Additives on Microvia Filling by Copper Electroplating

Alkyl-terminated PEG Suppressors for Copper Electroplating and Their Hydrophilic and Hydrophobic Properties

Copolymer of Pyrrole and 1,4-Butanediol Diglycidyl as an Efficient Additive Leveler for Through-Hole Copper Electroplating

Effect of bromide ions and polyethylene glycol on morphological control of electrodeposited copper foam

Computational and experimental study of a novel L-Cysteine hydrochloride leveler for copper electroplated via fill in redistribution layers

Temperature-dependent inhibition of PEG in acid copper plating: Theoretical analysis and experiment evidence

Interactive Effects of Additives and Electrolyte Flow Rate on the Microstructure of Electrodeposited Copper Foils

An SERS study of the galvanostatic sequence employed for the electrochemical deposition of Copper in the fabrication of Interconnects

Stochastic Modeling of Organic Additives in Cu Electroplating

Studies of polixetonium chloride as a novel, hypotoxic and single additive of copper electronic plating for microvia void-free filling in printed circuit board application