Abstract:The performance of superconducting magnets is greatly dependent on the size and uniformity of the superconducting filaments within the wire. However, in the fabrication of Bi 2 Sr 2 CaCu 2 O x (Bi2212) wires using ceramic oxide as the superconducting filaments, we face multiple challenges including filament fragility, poor uniformity, and non-smooth Ag/superconductor interfaces. These challenges primarily stem from the significantly lower plastic deformation capability of ceramic oxide powder filaments compared to metal matrices. To address these challenges, this study focuses on the modification of ceramic oxide precursor powders. Through the utilization of low-temperature, low oxygen partial pressure ( p O 2 ) heat treatment, we have observed significant changes in the Cu chemical states and lattice parameters within the Bi2212 grains. These alterations have proven to be highly effective in reducing the energy required for grain sliding and, in turn, enhancing the plastic deformation properties of the Bi2212 oxide filament. Furthermore, post-annealing the oxide powder under low p O 2 conditions narrows the gap in plastic deformability between the Ag sheath and the oxide filaments, resulting in improved filament uniformity and a smoother Ag/oxide interface in Bi2212 wires. Notably, the Bi2212 grains exhibit an orderly arrangement within the wires. As a result of these improvements, the critical current density ( J c ) of the final wires increases by an impressive 70 %. The outcomes of this study are not only crucial for producing Bi2212 magnets with higher magnetic field strength, improved magnetic field uniformity, and enhanced operational stability, but also offer fresh insights and methodologies for advancing the field of superconducting materials.

Significant improvement of the critical current of MOD-derived YBa<sub>2</sub>Cu<sub>3</sub>O<sub>7-δ </sub>-coated conductors by post-annealing treatment

Significant Improvement of the Critical Current of MOD-derived YBa2Cu3O7-δ -Coated Conductors by Post-Annealing Treatment

Advance in Long-Length REBCO Coated Conductors Prepared by Reel-to-Reel Metalorganic Solution and Ion-Beam-Assisted Deposition

Enhancement of Pinning Role by Nonstoichiometry in YBa2Cu3O7−y Superconductors

Improvement of Surface Morphology and Critical Current Density of YDy 0 . 2 Ba2Cu 3 . 3 O7−δ Thick Films by Inserted RE2O3 Thin Films

Oxygen Order Control by Post-Annealing for Optimizing Critical Temperature of YBaCuO Coated Conductors with Silver Protective Layer

Improved Superconductivity and Structural Mechanism Analysis of Y0.55Gd0.45Ba2Cu3O7–x/SrTiO3/Y0.55Gd0.45Ba2Cu3O7–x Tri-layer

Property Improvement of 600-Nm-thick YBCO Superconducting Films Fabricated Using a Pb-Modified MOD Method

Melt Growth of YBa 2 Cu 3 O 7-δ by Using BaCu 2 O 2 and Y 2 BaCuO 5 in Ag-Sheath

Crucial Role of Oxygen-Deficient LaMnO3−δcap Buffer Layer in Enhancement of Current Carrying Capability of MOD-YBCO Coated Conductors

Fabrication and Analysis of Tri-layer YBa 2 Cu 3 O 7− δ Thick Films by Low-Fluorine MOD Method

Fabrication and Analysis of Tri-layer YBa2Cu3O7−δ Thick Films by Low-Fluorine MOD Method

Thick $\Hbox{yba}_{2}\hbox{cu}_{3}\hbox{o}_{7-\Delta}$ Superconducting Films by Low-Fluorine Metallorganic Solution Deposition

Effect of Yb2O3 Additives on Structure and Transport Properties of YBa2Cu3O7-δ

Significantly Improving the Flux Pinning of YBa2Cu3O7‐δ Superconducting Coated Conductors via BaHfO3 Nanocrystal Addition Using Multistep Film Growth Method

Surface characterization of as-grown CeO2 cap layer morphology evolution and critical current density of post-deposited YBCO films

Effects of BaCuO_2 addition in YBa_2Cu_3O_(7-δ) on the critical current density

Improvement of plastic deformation property and current carrying capacity of Bi2212 wires through low oxygen partial pressure post-annealing of precursor

Nucleation and Epitaxy Growth of High-Entropy REBa2Cu3O7-δ(RE=Y,Dy,Gd,Sm,Eu)thin Films by Metal Organic Deposition

Fabrication And Analysis Of Tri-Layer Yba2cu3 O (7-Delta) Thick Films By Low-Fluorine Mod Method

Nucleation and epitaxy growth of high-entropy REBa2Cu3O7– (RE= Y, Dy, Gd, Sm, Eu) thin films by metal organic deposition