Abstract:AISI 317 L stainless steel replaces 316 L grade in some applications due to its superior mechanical strength and corrosion resistance. Aiming at expanding its applicability to structural applications, ongoing studies are dedicated to overcoming the trade-off between strength and ductility. The stacking fault energy decreases with deformation temperature and favors stacking faulting, (nano)twinning and strain-induced martensite (SIM) formation, resulting in severe microstructural fragmentation. The effect of temperature on deformation behavior of AISI 317 L steel was investigated in samples rolled at room temperature to thickness reductions of 50% and 85% and at 77 K to reductions in thickness of 10% and 50%. The microstructural evolution was followed by scanning electron microscopy, Vickers microhardness, X-ray diffraction, magnetization, electron backscatter diffraction (EBSD) and electron channeling contrast imaging (ECCI). The nucleation sites in the early stages of the transformation sequence γ → ε → α' were identified in the 10% cryorolled sample. The highest volume fraction of α'-martensite reached 45.8% in the cryorolled steel to 50% rolling reduction. Much lower fractions were obtained for samples rolled to 10% reduction at 77 K (2%) and at room temperature to 50% (0.3%) and 85% reductions (1.6%). The texture components after cryorolling were Goss and Brass for austenite; rotated cube, α- and γ-fibers for δ-ferrite and α'-martensite. The ε-martensite presents the typical texture of hcp metals with a c/a ratio above the ideal value and 〈0001〉 − oriented tilted about 21° from the normal direction towards the rolling direction. The results show cryorolling as an effective method for enhancing SIM formation and promoting severe microstructural refinement in AISI 317 L stainless steel.

Research on Deep-Drawn Strain of CR 304 Stainless Steel Plates Using Martensitic Transformation Analytical Method

A study of local mechanical properties of 304L SS welded joints subjected to cyclic straining using depth-sensing instrumented indentation

Microstructures-based Constitutive Analysis for Mechanical Properties of Gradient-Nanostructured 304 Stainless Steels

Variation In Mechanical Properties, Microstructures And Fracture Behavior Of 304 Stainless Steel During Low-Cycle Fatigue

The Investigation on Strain Strengthening Induced Martensitic Phase Transformation of Austenitic Stainless Steel: A Fundamental Research for the Quality Evaluation of Strain Strengthened Pressure Vessel

Study on deformation-induced martensitic transformation behavior of 304 and 316 stainless steels

A study of longitudinal cracking and the forming technology for deep-drawn austenitic stainless-steel cups

Quantitative analysis of strength and plasticity of a 304 stainless steel based on the stress-strain curve

Influence Of Different Deformation On Microstructure And Properties Of 304 Austenitic Stainless Stee6

Influence of Drawing Deformation on Stress Corrosion Cracking of 304 Stainless Steel

Crack Propagation and Strain-Induced Α’-Martensite Transformation in Selective Laser Melting 316L Stainless Steels

Microstructure evolution and mechanical properties of martensite stainless steel during repetitive high stress Loading-Unloading with small plastic deformation

Discussion on Factors of Unstable 304 Stainless Steel Stress Corrosion Cracking

Mechanical Behavior and Fatigue Performance of Austenitic Stainless Steel under Consideration of Martensitic Phase Transformation

Effects of temperature and strain amplitude on low-cycle fatigue behavior of 12Cr13 martensitic stainless steel

Insight in the Impact of Pre-Deformation on Structure - Deformation - Property Relationship in Cr-Mn-N Stainless Steel

Anisotropic plasticity deformation during micro-deep drawing of 304 foils: An experimental and numerical investigation

Strain-induced martensite formation in cryorolled AISI 317 L stainless steel

Effect Of Strain Rate On The Deformation-Induced Martensite Transformation And Mechanical Behavior Of Austenitic Stainless Steels For Cold Stretched Pressure Vessels

Abnormal Evolution of Pitting Behavior of Warmly Pre-Strained Austenitic Stainless Steels

Investigation on Creep Deformation and Age Strengthening Behavior of 304 Stainless Steel under High Stress Levels