Abstract:In this article, the drag characteristics of an underwater vehicle propelled by a synthetic jet (SJ) is numerically studied. The underwater vehicle studied is REMUS Autonomous underwater vehicle (AUV). The cruising speed studied is up to 10 knots. The actuation parameters of the SJ actuator are the same under different cruising speeds. When the SJ actuator works, the drag of the vehicle changes periodically. The SJ-induced additional pressure drag increases with increasing cruising speed. The additional friction force is negligible. The thrust of the actuator decreases with increasing cruising speed. The thrust outputted by the SJ actuator when used for underwater vehicle propulsion is smaller than the thrust of an isolated actuator. The mathematical model of the additional drag, the model of the thrust, and the velocity distribution is given to assist the analysis in this article. 1. Introduction The advance in propulsion technique is the key to the evolution of underwater robots. The most common method for underwater robot propulsion is using screw propellers. Thrust is generated through the high speed rotation of the blades. The fluid is accelerated not only in the axial direction but also in the radial direction; however, only fluid acceleration in the axial direction can generate thrust. A significant part of the energy is wasted in the radial direction without thrust generation. As a result, the efficiency of screw propellers is low. Furthermore, the protruded screw propellers induce significant added resistance. This further reduces the total hydrodynamic efficiency of the vehicle. Nature always inspires the technical revolution in engineering. In nature there exist many marine creatures such as squids adopting jet propulsion. The jet created by squids is called pulsed jet. On the other hand, the jet of screw propellers is called steady jet. Studies about pulsed jet showed that compared with the steady jet, pulsed jet possess higher propulsion efficiency (Krueger 2001; Krueger & Gharib 2003, 2005; Moslemi & Krueger 2010; Lydia et al. 2011; Robert & John 2013). Seikman (1963), Weihs (1977), and recently Krueger and Gharib (2003) have shown that pulsed jets can give rise to a greater average thrust than steady jets of an equivalent mass flow rate. Lydia A. Ruiz, Robert W. Whittlesey, and John O. Dabiri found through experiment that pulsed jet has a propulsion efficiency that is 40% higher than that of steady jet, and a drag-based hydrodynamic efficiency increase more than 70% (Lydia et al. 2011). The mechanism behind this high efficiency is the formation of the vortex. The vortex will induce a radial velocity gradient at the nozzle exit. The velocity distribution becomes more ununiform compared with steady jet. As a result, the pressure at the nozzle exit will increase. This is observed by Krueger through experiment.

A Thrust Test Method for Water Ramjet Engine

Design Method of Water Jet Pump Towards High Cavitation Performances

The Research on High-Speed Gas Jet of Rocket Nozzle Underwater

Numerical Study of Supersonic Jet Characteristics of Underwater Solid Rocket Engine

Three-Dimensional Numerical Simulation of Air Exhausted from Submerged Nozzles

Design of Contra-Rotating Waterjet Pump Based on High Cavitation Performances

Investigations into the unsteady internal flow characteristics for a waterjet propulsion system at different cruising speeds

Numerical Simulation of Underwater Supersonic Jet of Vehicle with Shell-Shaped Flow Control Structure

A Study on the Hydrodynamic Characteristics of a Synthetic Jet Propelled Underwater Vehicle

Numerical Simulation on Field Characteristics of the Horizontal Gas Jet Flow of Underwater Vehicle

Design and analysis of the scramjet nozzle with contact discontinuity

A New Design Method of Single Expansion Ramp Nozzles under Geometric Constraints for Scramjets

Analysis of Ventilated Cavitation Around A Cylinder Vehicle with Nature Cavitation Using A New Simulation Method

Effect of self-excited oscillation of three-dimensional rectangular shock-induced thrust vector nozzle jet

A Performance Simulation Methodology for a Whole Turboshaft Engine Based on Throughflow Modelling

Numerical Analysis on Self-Propulsion of a Waterjet-Propelled Ship with Different Propulsion Models

Numerical Investigation of Hydrodynamic Characteristics of a Rim-Driven Thruster Coupled with an Underwater Vehicle

Experimental and numerical investigations of a scramjet nozzle at various operations

Numerical Simulation of Inner Flow Field of a Pintle Injector Variable Thrust Rocket Engine

Design and simulation of a micro thrust solenoid valve nozzle based on CFD&DOE optimization analysis

Numerical evaluation of acoustic characteristics and their damping of a thrust chamber using a constant-volume bomb model