Abstract:Nanosized copper oxide-zirconia particles containing 10-30 mol% of copper were prepared by using a precipitation technique in aqueous tetramethylammonium hydroxide solutions. Two methods, in situ (INS) and step-by-step (SBS), which differed in the time when the copper salt was introduced to the synthesis procedure, were used, and this allowed a comparison of the properties of the final powders produced using the two modes of preparation. The surface areas and phase compositions were different for the samples prepared from the two different methods after calcination at 500 degreesC. A surface area of 168 m(2) g(-1) was obtained for the sample prepared with the SBS method and 121 m(2) g(-1) for the INS method, both contain 30 mol% copper. Tetragonal ZrO2 was observed from X-ray diffraction patterns for all samples prepared with the SBS method, however, no separate phase of copper or copper oxide was observed. It is proposed that all of the copper is finely distributed on the surface of the ZrO2 particles with the SBS method. For the samples prepared from the INS method, tetragonal ZrO2 was obtained at a low copper content and the peaks indexed to tetragonal ZrO2 shifted to higher angle with the increase of copper content, indicating copper ions being incorporated into the lattice. An amorphous compound was obtained at high copper content (30 mol%). The phase change with the calcination temperature was also investigated for the INS sample containing 30 mol% copper. The studies show that tetragonal ZrO2 and copper oxide were present after calcination at 400 degreesC, and tetragonal ZrO2 with a small amount of monoclinic ZrO2, as well as copper oxide, formed after calcination at 700 degreesC. However, after heating at 500 degreesC, amorphous compounds were obtained, suggesting that 500 degreesC could be a phase transition point. The incorporation of copper in the ZrO2 lattice resulted in a loss of order in the ZrO2 structure when calcined at 500 degreesC, with a further increase in the calcination temperature leading to the phase change.

Preparation and Phase Transition Kinetics of ZnO-coated Ultrafine TiO_2 Particles

The Thermal Analysis, Crystal Growth And Structure Transformation Of Nano-Scale Tio2 Prepared By Ticl4 Hydrolysis

Morphology Investigation of Hydrothermally Prepared ZnO Micro-Crystals Influenced by Cu2+ Ions

Preparation of Zirconia-Doped Titania Nanopowders by Co-Precipitation Method and Corresponding Phase Transformation

Preparation and Properties of CaTiO_3:Zn Nanoparticles Based on Sol-Gel Method

Preparation of Nanoparticle WO_3-doped TiO_2 and Research on Its Photocatalytic Activity

The Annealing Effect on the Microstructures and Phase Transformation of the TiO2 Layer in ZnO/TiO2 Core−Shell Nanostructures

Preparation of ZnO Particles by Precipitation Transformation Method and Its Inherent Formation Mechanisms

Phase structure, surface properties and photocatalytic activity of Zn2+- doped TiO2 nanopowders

Synthesis of Pb(Zr0.52Ti0.48)O3(PZT) Powder by A Partial Lead Oxalate Coprecipitation Method

Solid-phase Synthesis and Characterization of ZnO-TiO 2 System

Preparation and characterization of CuO–ZrO2 nanopowders

Preparation of nano-ZnO by direct precipitation method under ultrasonic radiation and surface modification study

Study on Phase Transition of Nano-Size TiO2 During the Heat Treatment

Preparation of TiO2 Powders with Different Morphologies by an Oxidation-Hydrothermal Combination Method

Phase Formation During Deposition of Tio2 Coatings Through High Velocity Oxy-Fuel Spraying

Hydrothermal synthesis and characterization of (Zr1−xSnx)TiO4 (x = 0.05–0.20) powders

Preparation of ZnO@TiO2 Nanotubes Heterostructured Film by Thermal Decomposition and Their Photocatalytic Performances

Preparation and characterization of TiO2 nanocomposites

Praparation and Characterization of Powder of nano-ZnO Coated by ATO

Synthesis, characterization and study of the structural change of nanobelts of TiO2 (H2Ti3O7) to nanobelts with anatase, brookite and rutile phases