Abstract:The anionic solution copolymerization of butadiene/styrene with n-butyllithium(n-BuLi) initiator, tetrahydrofuran(THF) modifier, and cyclohexane solvent, was studied. The study was carried out experimentally in an agitated tank reactor of 2 liters employing continuous operation mode. The reaction conversion rate of monomers, molecular weight and distribution of the copolymer, and micro-structure of the copolymer were analyzed by gas chromatograph, gel permeation chromatograph, and nuclear magnetic resonance, respectively. The effects of the mean residence time and the THF/Li+ ratio on the reaction conversion rate, molecular weight and molecular weight distribution, and the micro-structure of copolymer were investigated. The results showed that a randomized copolymer of butadiene/styrene with proper micro-structure can be obtained by anionic continuous solution copolymerization of butadiene/styrene with n-butyllithium(n-BuLi) initiator, tetrahydrofuran(THF) modifier, and cyclohexane solvent. The mean residence time has remarkable effect on the reaction conversion rate, and has effect to a certain extent on the micro-structure of copolymer. The effect of the THF/Li+ ratio on the copolymerization rate of butadiene and styrene are notable. The reasonable THF/Li+ ratio was found to be 70. The effect of the THF/Li+ ratio on the combined styrene is significant. The effect of the THF/Li+ ratio has effect to a certain extent on 1,2- structure, 1,4- structure , and cis/trans-structure of the copolymer. The results also showed that the effect of the THF/Li+ on the average molecular weight of copolymer is considerable, and that the effect of THF/Li+ ratio on the molecular weight distribution is not significant.

Research on Boosting Polymerization Temperature to Increase Output of Styrene Butadiene Rubber

KINETICS OF BULK GRAFT COPOLYMERIZATION OF STYRENE ONTO RUBBER

Phase inversion during bulk copolymerization of N-phenylmaleimide/styrene in presence of polybutadiene (II): Effects of operation conditions and recipes on occurrence of phase inversion and structure of rubber phase

Polybutadiene Vitrimers with Tunable Epoxy Ratios: Preparation and Properties

Ab initio RAFT emulsion polymerization of butadiene using the amphiphilic poly(acrylic acid-b-styrene) trithiocarbonate as both surfactant and mediator

Research of Styrene/Aerylonitrille/N-Phenlymaleimide Emalsion Copolymerization

Copolymerization Kinetics of Synthesis of Styrene and Butadiene Rubber Using Tetrahydrofufuryethylether As a Polar Modifier under the High Temperature

Ab Initio Batch Emulsion Raft Polymerization Of Styrene Mediated By Poly(Acrylic Acid-B-Styrene) Trithicicarbonate

Styrene polymerization with ternary neodymium-based catalyst system: effects of catalyst preparation procedures

Study on Kinetics of Styrene/Butyl Acrylate/Crosslinker Emulsion Copolymerization

Ab Initio RAFT Emulsion Copolymerization of Styrene and Acrylonitrile

Studies on Anionic Continuous Solution Copolymerization of Butadiene/Styrene with N-Buli Initiator

Investigation of Preparation of Acrylate Rubber with Solution Polymerization

Toward Polymer Product Design. I. Dynamic Optimization of Average Molecular Weights and Polydispersity Index in Batch Free Radical Polymerization

Suppressing the Long‐chain Branching in the Synthesis of Poly(styrene‐b‐butyl Acrylate‐b‐styrene) in RAFT Emulsion Polymerization by Tuning the Interfacial Properties

INFLUENCE OF POLAR MODIFIERS ON THE ANIONIC SOLUTION 1,3-BUTADIENE POLYMERIZATIONS

Synthesis of styrene-butadiene rubber latex for cement concrete modification

A Comparative Study on Emulsion Polymerization Processes of Styrene Initiated by Water-soluble and Oil-soluble Initiators

Effect of Polymerization Conditions on Reactive Kinetics of Butyl Acrylate

Synthesis of Acrylonitrile-Butadiene-Styrene Copolymers Through Interface-Initiated Room-Temperature Polymerization

Industrial scale experiment of styrene-butadiene rubber latex for cement