Abstract:RAFT polymerization is a type of psudo-living radical polymerization. In order to synthesize high pure block copolymers by RAFT polymerization, it is desirable to suppress the irreversible termination which may result in the formation of dead chains. For polymers less than 5 x 10(4) g/mol, the dead chain fraction could remain to be lower than 0.1 by reducing the initiator concentration. In the synthesis of block copolymers, the dead chains formed in the first stage are actually contaminant. Targeting to the synthesis of high pure block copolymers with high molecular weight using RAFT polymerization, we studied the copolymerization of butyl acrylate and styrene mediated by 1-phenylethyl phenyl-dithioacetate (PEPDTA) as a RAFT agent. The influences of the type of initiators (AIBN (2-2'-azobis ( isobutyronitrile)), ACC ( 1-1'-azobis ( cyclohexane-carbonitrile)), the concentrations of initiator and polymerization temperature on the copolymerization kinetics and molecular weight and its distribution were investigated. When AIBN was used, the polymerization would stop at middle monomer conversion, which limited the increase of molecular weight of the copolymer if we reduced the initiator concentration. It was found that only with the initiator (ACC) with small decomposition rate constant and high polymerization temperature, the block copolymer with high molecular weight and small fraction of dead chains ( < 0.1) could be synthesized. The reason for these quite strict requirements is that the initiator concentration should remain far below that of the conventional radical polymerization, which is limited by the very low RAFT concentration.

Ab Initio RAFT Emulsion Copolymerization of Styrene and Acrylonitrile

Ab Initio Batch Emulsion Raft Polymerization Of Styrene Mediated By Poly(Acrylic Acid-B-Styrene) Trithicicarbonate

Toward well-controlled ab initio RAFT emulsion polymerization of styrene mediated by 2-(((Dodecylsulfanyl)carbonothioyl)sulfanyl)propanoic acid

Ab initio RAFT emulsion polymerization of butadiene using the amphiphilic poly(acrylic acid-b-styrene) trithiocarbonate as both surfactant and mediator

RAFT Ab Initio Emulsion Copolymerization of Γ-Methyl-α-methylene-γ-butyrolactone and Styrene

Ab Initio Emulsion and Miniemulsion Polymerization of Styrene Mediated by a Cyclohexenyl-Functionalized Amphiphilic RAFT Agent

Modeling and Experimentation of RAFT Solution Copolymerization of Styrene and Butyl Acrylate, Effect of Chain Transfer Reactions on Polymer Molecular Weight Distribution

Ab Initio Emulsion RAFT Polymerization of Vinylidene Chloride Mediated by Amphiphilic Macro‐raft Agents

Raft Ab Initio Emulsion Polymerization Of Styrene Using Poly(Acrylic Acid)-B-Polystyrene Trithiocarbonate Of Various Structures As Mediator And Surfactant

Reversible Addition–fragmentation Transfer (RAFT) Copolymerization of Methyl Methacrylate and Styrene in Miniemulsion

Reversible addition fragmentation transfer (RAFT) polymerization of styrene in a miniemulsion: A mechanistic investigation

Kinetics of RAFT Emulsion Polymerization of Styrene Mediated by Oligo(acrylic Acid‐b‐styrene) Trithiocarbonate

Soap-Free Emulsion Polymerization of Styrene Using Macro-RAFT Agent to Make Cationic Latex

The Synthesis of High Molecular Weight Block Copolymers by Raft Polymerization

Suppressing the Long‐chain Branching in the Synthesis of Poly(styrene‐b‐butyl Acrylate‐b‐styrene) in RAFT Emulsion Polymerization by Tuning the Interfacial Properties

Synthesis of Well-Defined Polystyrene with Molar Mass Exceeding 500 kg/mol by RAFT Emulsion Polymerization

Batch-semi-batch Two-Stage RAFT Mini-Emulsion Polymerization of Styrene

Butyl Acrylate RAFT Polymerization in Miniemulsion

Reversible addition–fragmentation chain transfer polymerization of methyl methacrylate in emulsion

Comparison of RAFT Ab Initio Emulsion Polymerization of Methyl Methacrylate and Styrene Mediated by Oligo(methacrylic Acid‐b‐methyl Methacrylate) Trithiocarbonate Surfactant

Ab Initio Reversible Addition–fragmentation Chain Transfer Emulsion Polymerization of Styrene/butyl Acrylate Mediated by Poly(acrylic Acid)‐block‐polystyrene Trithiocarbonate