Abstract:Lattice distortion, which is intended to increase the yield strengths of alloys, is central to alloy design. This study focuses on investigating the close connection between microstructure and mechanical properties of (CoNiV)97Al3 medium-entropy alloys (MEAs) in the as-cast and annealed states. The grain size and phase composition of the alloys were optimized by combining the large deformation cold-rolling and high temperature annealing treatment, and the toughening mechanism of the alloys was evolved. After annealing at 900 and 950°C, a small amount of diffuse B2 phase appears within the alloy, which is able to strengthen the alloy to obtain high yield strength. Since intermetallic compounds such as Ni3Al are extremely unstable, they will decompose during annealing at higher temperature (1000°C), the alloy transforms into a single FCC phase. Therefore, the as-cast and annealed (CoNiV)97Al3 alloy exhibited excellent mechanical properties, including yield strengths of 0.8–1.1GPa, ultimate tensile strengths of 1.05–1.7GPa, and an optimal elongation of 36.7%. Combined with the mechanical properties and microstructure of the as-cast and annealed (CoNiV)97Al3 MEAs, the alloy strengthening was mainly attributed to the synergistic effect of dislocations, solid solution phases, and B2 brittle precipitated phases, while the good ductility was mainly due to the annealing twins. Thus, harmonizing multiple strength/toughness mechanisms can lead to a more optimal alloy strength–plasticity equilibrium point.

The Microstructures and Mechanical Properties of CoNiCrx Medium-Entropy Alloys

Microstructure and Mechanical Properties of the As-Cast and Annealed CoNiV-based MEAs with Al Addition

Microstructure and Mechanical Properties of CoCrFeNi_2Al_1-xW_x High Entropy Alloys

Microstructure and Mechanical Properties of New AlCo<sub>x</sub>CrFeMo<sub>0.5</sub>Ni High-Entropy Alloys

Effect of Microstructure Evolution on Micro/Nano‐Mechanical Property of Fe–Co–Ni Ternary Alloys Solidified under Microgravity Condition

Study on Microstructure Evolution and Mechanical Properties of CoCrFeNiTiAlx High Entropy Alloys

Microstructure and Mechanical Property of As-Cast, -Homogenized, and -Deformed AlxCoCrFeNi (0≤x≤2) High-Entropy Alloys

Investigating the Micro and Nanomechanical Properties of CoCrFeNi-C High-Entropy Alloys Containing Eutectic Carbides

Microstructure and mechanical properties variation with Ni content in Al0.8CoCr0.6Fe0.7Nix (x = 1.1, 1.5, 1.8, 2.0) eutectic high-entropy alloy system

Microstructures and Mechanical Properties of Multi-component AlxCrFe2Ni2Mo0.2 High-Entropy Alloys

Microstructure and Properties of Multi-Component AlxCoCrFeNiTi0.5 High-Entropy Alloys

Microstructures and Mechanical Properties of Multi-component Al<sub><i>x</i></sub>CrFe<sub>2</sub>Ni<sub>2</sub>Mo<sub>0.2</sub>High- Entropy Alloys

Superior Low Temperature Mechanical Properties and Microstructure of (nicocr)95v5 Medium Entropy Alloy

Microstructure and Mechanical Properties of the W-Ni-Co System Refractory High-Entropy Alloys

Microstructures, Compressive Properties, and Microhardness of NiAl-Cr(Mo) Eutectic Alloys with Various Ni Contents

Mechanical properties of nanocrystalline Ni-Co alloy with different microstructures

Effect of C Content on Microstructure and Tensile Properties of As-Cast CoCrFeMnNi High Entropy Alloy

On Microstructure and Mechanical Performance of AlCoCrFeMo0.5Nix High-Entropy Alloys

Mechanical and Tribological Performance of CoCrNiHfx Eutectic Medium-Entropy Alloys

Effect of Ni/Cr Ratio on Phase, Microstructure and Mechanical Properties of NixCoCuFeCr2−x (x = 1.0, 1.2, 1.5, 1.8 Mol) High Entropy Alloys

Microstructure evolution and mechanical properties of CoCrFeNiAl0.3 high entropy alloy produced by ball milling in combination with thermomechanical consolidation