Abstract:QN1803, a high-strength stainless steel, has been developed recently, and its tensile yield strength can be approximately 40 % (or more) higher than the commonly-used EN1.4301, while its cost is 20 % lower due to its reduced nickel content. This high-performance material can potentially be used in many applications, and one such application is plate girders. However, no experimental work has been undertaken. This issue is addressed herein. A detailed experimental study comprising seven plate girder tests is presented in this study. The plates were austenitic grade QN1803 and EN 1.4301, and the depth of web was fixed as 500 mm, 600 mm and 700 mm. For comparison, specimens with rigid end posts were also tested. The initial geometrical imperfections were first determined from three-dimensional (3D) scanning. Finite element models (FEMs) incorporating the material non-linearity and initial geometric imperfections are then developed and validated against the test results. A total of 15 tensile coupon tests are performed to investigate the effects of rolling directions on the material properties, with longitudinal coupons, diagonal coupons, and transverse coupons all being tested. The test results indicated that the 0.2 % proof stresses of the transverse coupons were approximately 8.5 % higher than that of the longitudinal coupons. The plate girder tests suggested that the shear buckling strength of QN1803 members was increased by 38.2 % on average compared to EN 1.4301 members. The design rules for determining the shear buckling strength of plate girders as provided in Eurocodes (EN 1993-1-4 +A1) (2015), North American Specification (ANSI/AISC 370-21) (2021) and those proposed by Chen et al. (2023) were evaluated. The results demonstrated that the design formulas proposed by Chen et al. (2023) can closely calculate the shear buckling strength of such QN1803 members.

Mechanical Properties and Constitutive Models of Butt-Welds in Q345GJ Thick Steel Plates

Mechanical properties and constitutive model of Q345GJ thick steel plate in China

Low Cycle Fatigue Properties and Fracture Mechanism of Q345qC Steel and Its Welded Joint

Mechanical Properties of Material in Q345gj-C Thick Steel Plates

Mechanical Properties of Butt Weldments Made with Q345B Steel and E5015 Electrodes at Different Temperatures

Experimental Research On Tensile Properties Of Q460 High Strength Steel Butt Welds

Mechanical properties of butt weldments made with E5515-G electrodes at high temperature

Experimental and numerical study on strength of high-strength steel double-V butt-welded joint

Microstructure and mechanical properties of T-joints in mid-thick Q345 steel plates welded using deep penetration tungsten inert gas welding

Experimental Investigation on Fatigue Crack Growth Performance of Q690D Steel Butt Weld

Cyclic Behavior of Q345GJ Steel Used in Energy Dissipation Shear Links

Experimental Study on Mechanical Properties and Fracture Toughness of Structural Thick Plate and Its Butt Weld along Thickness and at Low Temperatures

Investigation of Microstructure and Mechanical Properties of High-Depth-to-Width-Ratio Horizontal NG-GMAW Joint for S500Q Steel

Investigation of the Fracture Behavior of High-Strength Structural Steel and Welds Based on Micromechanical Models

EXPERIMENTAL RESEARCH ON FATIGUE PERFORMANCE AND FRACTURE MECHANISM OF Q345QD BUTT WELDS

Mechanical Behavior of Q460 High-Strength Steel under Low-Cycle Fatigue Loading

Experimental and Simulation Study on Welding Characteristics and Parameters of Gas Metal Arc Welding for Q345qD Thick-Plate Steel

Research on the constitutive relation of different material zones of weathering steel Q355GNHB

Experimental study on the Z-direction properties of the steel thick plate and its butt weld

Material Properties and Shear Behaviour of QN1803 High-Strength Stainless Steel Plate Girders

Ultra-Low Cyclic Fatigue Fracture of Q235B and Q345B Steels and Their Butt Welded Joints