Abstract:The latched comparator is a fundamental component of all ADC topologies. Thermal noise, kickback noise, and offset voltage impact the energy efficiency of the comparator significantly. In cardiac IMD ADCs, latched comparator kickback noise may impact resolution, accuracy, and settling time. This paper describes the design and development of an a low-power dynamic latched comparator optimised for biomedical applications and running at 1V. The suggested comparator is achieved on a 45 nm CMOS technology node, having the main goal of reducing kickback noise. The main concept of the recommended comparator has been utilizing the novel resetting approach and kickback noise reduction approach to preserve the charge and kickback noise, respectively. This approach aids in minimizing delay, power consumption, and kickback noise using shared charging logic. The charging-sharing technique involves using a single-pass transistor positioned across two output nodes. The pass transistor distributes the charge evenly across two output nodes throughout the reset phase. Due to the shared charging of the load capacitances, the voltage at the output nodes would not drop under the threshold value. As a result, the input signal could be evaluated more quickly during the regenerative stage. The comparator's delay is calculated using a rigorous statistical analysis considering the circuit's random factors. The offset of the proposed comparator is verified using thorough Monte Carlo simulations. The comparator reduces power while preserving noise. Also, the measured simulation results of recommended comparator outperform state-of-the-art comparators regarding kickback noise, delay, power consumption, and power delay product (PDP). The input voltage inversely affects the comparator's delay. Further, the simulation shows that the comparator consumes 9.36μW at 1 V and 1GHz sampling frequency. The simulation results confirm that the suggested comparator effectively reduces power consumption by atleast 66.98%. The proposed comparator has less PDP value by 44.44%. Also, suggested comparator effectively reduces offset voltage by 7.6% but with a corresponding increase in the area by 5%. Additionally, the comparator successfully reduces kickback noise by 44.6%. The obtained results are not silicon proven and bound to be in the pre-silicon stage. The low-power behaviour of the suggested technique is validated using analytical derivations, PVT corner analysis, and post-layout simulation.

A Six-input Dynamic Comparator with Low Kickback Noise at Cryogenic Temperature

A Threshold Control Technique for CMOS Comparator Design

A Low Power and High Speed CMOS Comparator at Croyogenic Temperature

A Three-Stage Dynamic Comparator for SAR ADC Optimized for Reduced Kickback Noise and Ultra-Low Delay

A Low Power Continuous Time Hysteresis Comparator with an Average Current Consumption of 614na at 1.5 Voltage

A Low Kickback Noise and Offset Calibrated Dynamic Comparator for 2b/c Sar Adc

A Low Kick Back Noise Latched Comparator for High Speed Folding and Interpolating ADC

Design of a Low-Power Dynamic Latched Comparator for Biomedical Applications

A 6-Bit 700-Ms/s Single-channel SAR ADC with Low Kickback Noise Comparator in 40-Nm CMOS

A Dynamic CMOS Comparator with High Precision and Resolution

A Cryogenic 8-Bit 32 MS/s SAR ADC Operating Down to 4.2 K

A Comparator-Reused Dynamic-Amplifier for Noise-Shaping SAR ADC

A Novel Latched Comparator with Low Kickback Noise

A 0.2-Mv 20-Mhz 600-Μw Comparator

A precise dynamic CMOS comparator

A Low Noise High Speed Dynamic Comparator Insensitive to PVT and Common-mode Input

Design and Analysis of Low Power and High-Speed Dynamic Comparator with Transconductance Enhanced in Latching Stage for ADC Application

A Fully Synthesizable Dynamic Latched Comparator with Reduced Kickback Noise

A Three-Stage Comparator with High Speed and Low Power

A 288-Μw 6-Ghz Hybrid Dynamic Comparator with 54-Ps Delay in 40-Nm CMOS

A 0.9 V high‐speed dynamic bias latch‐type comparator employing a voltage‐controlled delay line