Abstract:Generally, the function of thermal interface material (TIM) is filling rough surfaces, eradicating air pockets, decreasing thermal resistance, and improving heat dissipating effects. On this basis, we provide the TIM with another identity, "adhesion", rendering it not only play a role of heat dissipation, but also serve as an adhesive to bond contacting surfaces. In this work, nano- to microscopic liquid metal (LM) droplets are embedded into the epoxy matrix to fabricate a LM-epoxy in-situ cured composite. By adding the curing agent, the LM-epoxy composite is cured into an entity structure, transforming from an amorphous grease state to a self-adaptive pad state. When the average droplet size is in a reasonable range of approximately 5–25 μm, the composite's thermal resistance ( R total ) decreases to 2.19 mm 2 K/W at 70% volume fraction with its adhesive strength of 0.497 MPa, and the thermal conductivity ( k TIM ) could increase to 10.05 W/(m·K) at 85%. Both R total and k TIM change rapidly for droplet size approximately ranging from 10 2 nm to 10 1 μm and then tend to level off when it further increases to 10 2 μm. A conception of equivalent contact thickness, δ, is presented to elucidate the contacting thermal resistance R c , and set up predictive models of R total for different volume fractions by considering the microscopic interfacial thermal resistance R b between filler and matrix or not. This composite simultaneously possesses characteristics of the low thermal resistance like thermal grease, the whole entity like thermal pad, and the anti-leak characteristics by in-situ cured process. Actual cooling tests show it has a considerable temperature difference of 4.75 °C lower than the commercial thermal grease at 650 W heating power. This in-situ cured strategy, via decreasing the thermal resistance and solving the problem of LM leakage, remarkably promotes the LM-TIMs achieving a broader application prospect in the future.

Patterned Liquid Metal Embedded in Brush-Shaped Polymers for Dynamic Thermal Management.

Encapsulated Solid-Liquid Dual Continuous Pathways with Low Modulus and High Thermal Conductivity for Dynamic Target Autonomous Thermal Management

3D Network of Liquid Metal‐Embedded Graphene via Surface Coating for Flexible Thermal Management

Alveoli‐Mimetic Synergistic Liquid and Solid Thermal Conductive Interface as a Novel Strategy for Designing High‐Performance Thermal Interface Materials

High-performance non-silicone thermal interface materials based on tunable size and polymorphic liquid metal inclusions

Liquid Metal Composites with Enhanced Thermal Conductivity and Stability Using Molecular Thermal Linker

Liquid metal-based flexible and wearable thermoelectric cooling structure and cooling performance optimization

Biomimetic Liquid Metal–Elastomer Composited Foam with Adjustable Thermal Conductivity for Heat Control

Multifunctional Liquid Metal‐Bridged Graphite Nanoplatelets/Aramid Nanofiber Film for Thermal Management

Highly Thermally Conductive and Flexible Thermal Interface Materials with Aligned Graphene Lamella Frameworks

Metal-Level Thermally Conductive yet Soft Graphene Thermal Interface Materials

Liquid Metal-Based Flexible Heat Sink for Adaptive Thermal Management

High Thermal Conductivity of Sandwich-Structured Flexible Thermal Interface Materials.

Controllable Construction of CNT-Interconnected Liquid Metal Networks for Thermal Management

PDMS/functionalized h-BN/liquid metal flexible composite with dual-network structure for achieving superior thermal conductivity and low thermal resistance via interfacial grafting

Thermal Interface Materials with Both High Through-Plane Thermal Conductivity and Excellent Elastic Compliance

Anisotropic and Heterogeneous Thermal Conductivity in Programmed Liquid Metal Composites Through Direct Ink Writing

Lightweight, Thermally Conductive Liquid Metal Elastomer Composite with Independently Controllable Thermal Conductivity and Density

Joint‐Inspired Liquid and Thermal Conductive Interface for Designing Thermal Interface Materials with High Solid Filling yet Excellent Thixotropy

Anti-leak, self-adaptive liquid metal-epoxy in-situ cured composites with ultra-low thermal resistance via flexible droplet inclusions

Patternable thermal conductive interface materials enabled by vitrimeric phase change materials