Abstract:Electron beam melting (EBM) is a promising powder bed fusion additive manufacturing (AM) technology for the preparation of complex refractory components due to the significant advantages of vacuum environment and high level in energy utilization, scanning speed and temperature in the build chamber. However, the fabrication of crack-free and refined W-based alloy remains a challenge. This study aims to address this problem by introducing 0.7 wt% carbon in EBM W-3.5Nb alloy. Results revealed that the as built W-3.5Nb alloy had a typical columnar structure with obvious solidification cracks along the grain boundary. Doping 0.7 wt% carbon generated refined microstructure, which was composed of the initial dendrite of tungsten and the eutectic phase in the dendrites gap. Due to the low distribution coefficient of carbon, the nucleation at the bottom of the molten pool was caused by constitutional supercooling in the front of liquid solidification in a single molten pool, and velocity of the solidification front was reduced by carbon concentration leading increased thermal supercooling. Supercooling (thermal supercooling together with constitutional supercooling) refined the microstructure of W-3.5Nb alloy effectively. Meanwhile, due to the formation of eutectic phase with low melting point, the fluidity of liquid phase at the terminal solidification was improved and the solidification cracks along the grain boundary were reduced. The carbon addition also played a significant role in alloy strengthening. The microhardness of the alloy increased from 382 HV to 696 HV, and the compressive strength increased from 962.89 MPa to 1892.56 MPa. These findings offer a new perspective on the AM fabrication of high-quality W-based alloys.

A Novel Performance Optimization Study in Additively Manufactured Tungsten-5 Wt.%rhenium Alloys Reinforced with Dilute Carbon

Alloying Effects on the Microstructure and Properties of Laser Additively Manufactured Tungsten Materials

Near crack free additive manufacturing of a novel W-Nb-C alloy

Crystal Plasticity Analysis of the Evolutions of Temperature, Stress and Dislocation in Additively Manufactured Tungsten

Cracking Mechanisms in Additively Manufactured Pure Tungsten from Printing Single Tracks, Thin Walls and Cubes

Cracking in Laser Additively Manufactured W: Initiation Mechanism and a Suppression Approach by Alloying

Refined W-3.5Nb alloy fabricated by electron beam melting via doped carbon

Crack Suppression in Additively Manufactured Tungsten by Introducing Secondary-Phase Nanoparticles into the Matrix

Cracking suppression in selective electron beam melted WMoTaNbC refractory high-entropy alloy

Interstitial Strengthening of a Cast and Wrought Ni-Based Heavy Density Matrix Alloy by Carbon Addition

Additive Manufacturing of High-Strength CrMnFeCoNi High-Entropy Alloys-Based Composites with WC Addition

Additive Manufacturing of High-Strength CrMnFeCoNi-based High Entropy Alloys with TiC Addition

Advancements and Perspectives in Additive Manufacturing of Tungsten Alloys and Composites: Challenges and Solutions

Dislocation Evolution During Additive Manufacturing of Tungsten

Effect of TaC addition on microstructure and microhardness of additively manufactured tungsten

Simulation and Experimental Investigation on Additive Manufacturing of Highly Dense Pure Tungsten by Laser Powder Bed Fusion

Unveiling the Intrinsic Rhenium Effect in Tungsten

Cracking Behavior in Additively Manufactured Pure Tungsten

A new design strategy for purifying and strengthening W alloy by self-decomposing in-situ nanoparticles

Overcoming the strength-ductility trade-off in an additively manufactured CoCrFeMnNi high entropy alloy via deep cryogenic treatment

Carbon Nanotubes (CNTs) Reinforced CoCrMoNbTi0.4 Refractory High Entropy Alloy Fabricated via Laser Additive Manufacturing: Processing Optimization, Microstructure Transformation and Mechanical Properties