Abstract:A submicro-pore containing proton exchange membrane (PEM) consisting of poly(ether sulfones) (PES) and polyvinylpyrrolidone (PVP) was successfully prepared through a scalable polymer blending method with monodispersed SiO2 solid spheres as a hard template. After doping with phosphoric acid (PA), an outstanding balance between proton conductivity and mechanical strength in these blends is obtained. The tensile strength of all the porous PES/PVP membranes ranges from 5.98 to 3.69 MPa with an increasing content of SiO2 from 10 wt% to 50 wt%, which satisfies the mechanical requirements of high-temperature proton exchange membrane fuel cells (PEMFCs). A proton conductivity of 0.09 S cm(-1) is obtained for the as prepared composite membrane with a PA doping level of 350 wt% at 180 degrees C under anhydrous conditions, comparable with the state-of-the-art PBI/PA membranes. The mechanism for the "balanced" properties is that after the PA doping treatment, the mechanical strength satisfies the requirements of high-temperature PEMFCs with a decreased content of PVP at 50 wt%, while the proton conductivity is improved under the cooperative proton transfers both along the "bonded acid" caged inside the pores and the PA-rich domain formed by "free acid" in the submicro-pores. Furthermore, the PEM fuel cell with PA doped porous PES/PVP exhibits a power density of 454 mW cm(-2) at 180 degrees C H-2/O-2 without external humidification. A fuel cell performance of similar to 520 mV at 0.2 A cm(-2) is maintained for 150 h without obviously decreasing. The submicro-pore containing PES/PVP blends allowed for a higher PA doping level, and consequently, enhanced proton conductivity, as well as improved mechanical strength and cell performance, showing potential for use as an alternative high-temperature PEM for fuel cells under anhydrous conditions.

High-performance and durable membrane electrode assemblies based on CeO2 and ePTFE double-reinforcement strategy for proton exchange membrane fuel cells operating at elevated temperatures

Development of Cathode Ordered Membrane Electrode Assembly Based on TiO2 Nanowire Array and Ultrasonic Spraying

Preparation of Membrane Electrode Assemblies for Proton Exchange Membrane Fuel Cells

Microporous Layer Containing CeO2-Doped 3D Graphene Foam for Proton Exchange Membrane Fuel Cells at Varying Operating Conditions.

Reinforced Integrated Membrane Electrode Assembly Based on Ionomer Wet-Binding and Eptfe Reinforcement Strategy for Proton Exchange Membrane Fuel Cells

The fabrication of integrated proton exchange membrane fuel cells: Excellent mechanical strength and electrochemical performance

Ce3+ Doped CeP2O7 Ceramic Electrolyte for High Temperature Proton Exchange Membrane Fuel Cell

Performance of PEMFC stack at elevated temperature

One Simple Method to Improve the Mass Transfer of Membrane Electrode Assembly to Realize Operation under Wide Humidity

Enhanced MEA Performance for an Intermediate-Temperature Fuel Cell with a KH5(PO4)2-Doped Polybenzimidazole Membrane

Double-Layer Expanded Polytetrafluoroethylene Reinforced Membranes with Cerium Oxide Radical Scavengers for Highly Stable Proton Exchange Membrane Fuel Cells

A High-Performance Membrane Electrode Assembly with an Ultrathin Proton Exchange Membrane Based on a Wet-Combining Interface Forming Strategy

An Asymmetric Membrane Electrode Assembly for High-Performance Proton Exchange Membrane Fuel Cells

High-temperature inorganic anion exchange membranes based on layered double hydroxides for anion exchange membrane fuel cell applications

Preparation of an Integrated Membrane Electrode Assembly for Proton Exchange Membrane Fuel Cells Using a Novel Wet-Bonding Strategy

Submicro-Pore Containing Poly(Ether Sulfones)/Polyvinylpyrrolidone Membranes For High-Temperature Fuel Cell Applications

Optimizing proton exchange membrane fuel cell performance at low-humidity via constructing additional anodic water-retaining membrane layer containing sulfonated multi-walled carbon nanotubes

Yttrium Doped Cerium Oxide As Free Radical Scavenger for Proton Exchange Membrane Fuel Cells

Finely Adjusted Intrinsically Microporous Copolyimide Electrolyte Membranes for Fuel Cells Operating in a Wide Temperature Range

Highly durable direct methanol fuel cell with double-layered catalyst cathode

Self-Assembly-Cooperating in Situ Construction of MXene–CeO2 As Hybrid Membrane Coating for Durable and High-Performance Proton Exchange Membrane Fuel Cell