Compact Half Adder on SOI Platform with Inverse Design

Houyu Chen,Caiyue Zhao,Yinghui Wang,Simei Mao,Lirong Cheng,Xuanyi Liu,Qian Li,H. Y. Fu

DOI: https://doi.org/10.1109/icocn59242.2023.10236374

2023-01-01

Abstract:We propose a compact half adder for optical combinational logic circuits. The device shows high transmission and flat spectrum with acceptable phase difference limit and controlled minimum feature size, making it robust for fabrication.

What problem does this paper attempt to address?

Compact All-Optical Half Adder Based on Topology Optimization

Houyu Chen,Jin Li,Lirong Cheng,Caiyue Zhao,Xuanyi Liu,Qian Li,H. Y. Fu

DOI: https://doi.org/10.1364/josab.506173

2024-01-01

Abstract:We proposed an inverse-designed compact half adder on a silicon-on-insulator platform with a footprint of 2µm×2µm. The optical power of SUM and CARRY is controlled by different input combinations, according to the truth table of a half adder. Topology optimization is applied to cope with multiple objective functions in such a combinational logic circuit. The transmittance at 1550 nm for CARRY with 11 input is 170.2%, with extinction ratios (ERs) of 27.1 and 5.8 dB for SUM and CARRY, respectively. The SUM and CARRY outputs have ERs over 22.0 dB and 5.7 dB from 1515 nm to 1600 nm. Phase condition and morphology analysis show that the device has high tolerance on phase fluctuation and fabrication. The proposed device with compact footprint, low insertion loss, and large bandwidth presents a novel, to the best of our knowledge, approach to achieve all-optical combinational logic circuits with inverse design.
Implementation of a Novel Optical Half-Adder

CX Yang,WS Wu,PC Yeh

DOI: https://doi.org/10.1016/0030-4018(96)00241-6

IF: 2.4

1996-01-01

Optics Communications

Abstract:A novel technique of performing optical logic operations and a compact optical half-adder based on beam coupling in photorefractive self-pumped phase conjugators are proposed and demonstrated.
Ultra-compact and low delay time all optical half adder based on photonic crystals

Fariborz Parandin

DOI: https://doi.org/10.1007/s11082-023-04603-4

IF: 3

2023-03-09

Optical and Quantum Electronics

Abstract:In this paper, an optical half adder is designed using photonic crystals. One of the features of this half adder is its small size. In the design of this structure, it has been tried to have a small size, shorter delay and high contrast ratio so that it can be used in the design of optical integrated circuits. For the sum and carry outputs, the obtained contrast ratio in the designed half adder is 15.4 dB and 7.4 dB, respectively. In addition, the proposed structure has a size of 70 μm 2 . The small size of this structure and the use of simple point defects, have caused the maximum delay time of this structure to be reduced to 0.07 ps. Due to these characteristics, this structure is suitable for high-speed optical integrated circuits.

engineering, electrical & electronic,optics,quantum science & technology
Standardized Design: On-chip Diffractive Optical Logic Operation Units with Ultra-compact Structures

Run Sun,Yuyao Huang,Wencan Liu,Tingzhao Fu,Sigang Yang,Hongwei Chen

DOI: https://doi.org/10.1364/cleo_at.2024.jth2a.83

2024-01-01

Abstract:With an ultra-compact footprint of 9×18μm2, on-chip diffractive optical logic operation units accomplish (N)AND, (N)OR, and X(N)OR utilizing a standardized structures with only 36 etching slots. It has outstanding integration capability and relaxed fabrication requirements.
Design of an all-optical half adder based on photonic crystal ring resonator

Fariborz Parandin,Arezoo Sheykhian

DOI: https://doi.org/10.1007/s11082-022-03810-9

IF: 3

2022-06-22

Optical and Quantum Electronics

Abstract:In this paper, a half adder was designed based on two-dimensional photonic crystals with small dimensions and a simple structure. Half adders are an important component of logic circuits, thus, designing a high-performance half adder can improve the function of computational circuits. In addition to the dimensions and simplicity of the structure, speed and accuracy were also considered in the design of this half adder. The respective proximity of the state outputs 0 and 1 of this circuit to zero exponentiation and the maximum exponentiation value has led to a significant distance between the two values of reasonable 0 and 1. cylindrical dielectric rods were employed in the air field. This half adder was designed to be utilized in the widely-used telecommunication frequency of 1550 nm. All computations are performed for TM mode and through using the finite difference methods in the domain of time (FDTD). The designed structure size was , which is suitable for optical integrated circuits.

engineering, electrical & electronic,optics,quantum science & technology
Inverse-designed Metamaterials for On-chip Combinational Optical Logic Circuit

Qingze Tan,Chao Qian,Hongsheng Chen

DOI: https://doi.org/10.2528/pier22091502

2023-01-01

Abstract:Optical analog computing has recently sparked growing interest due to the appealing characteristics of low energy consumption parallel processing and ultrafast speed, spawning it complementary to conventional electronic computing. As the basic computing unit, optical logic operation plays a pivotal role for integrated photonics. However, the reported optical logic operations are volumetric and single-functional, which considerably hinders the practical cascadability and complex computing requirement. Here, we propose an on-chip combinational optical logic circuit using inverse design. By precisely engineering the scattering matrix of each small-footprint logic gate, all basic optical logic gates (OR, XOR, NOT, AND, XNOR, NAND, and NOR) are realized. On this foundation, we explore the assembly of these basic logic gates for general purpose combinational logic circuits, including optical half-adder and code converter. Our work provides a path for the development of integrated, miniaturized, and cascadable photonic processor for future optical computing technologies.
Design of Ultra-Compact and Multifunctional Optical Logic Gate Based on Sb2Se3-SOI Hybrid Platform

Liuni Yang,Qiang Liu,Haoyuan Liang,Minming Geng,Kejin Wei,Zhenrong Zhang

DOI: https://doi.org/10.3390/nano14151317

2024-08-05

Abstract:Optical logic devices are essential functional devices for achieving optical signal processing. In this study, we design an ultra-compact (4.92 × 2.52 μm2) reconfigurable optical logic gate by using inverse design method with DBS algorithm based on Sb2Se3-SOI integrated platform. By selecting different amorphous/crystalline distributions of Sb2Se3 via programmable electrical triggers, the designed structure can switch between OR, XOR, NOT or AND logic gate. This structure works well for all four logic functions in the wavelength range of 1540-1560 nm. Especially at the wavelength of 1550 nm, the Contrast Ratios for XOR, NOT and AND logic gate are 13.77 dB, 11.69 dB and 3.01 dB, respectively, indicating good logical judgment ability of the device. Our design is robust to a certain range of fabrication imperfections. Even if performance weakens due to deviations, improvements can be obtained by rearranging the configurations of Sb2Se3 without reproducing the whole device.
Photonic crystal based integrated system for half adder and half subtractor operations

Snigdha Hazra,Sourangshu Mukhopadhyay

DOI: https://doi.org/10.1007/s11082-024-06731-x

IF: 3

2024-04-06

Optical and Quantum Electronics

Abstract:In this paper, the implementation of an integrated system of half adder and half subtractor based on 2D Si-air photonic crystal is proposed. The structure includes two input ports, one control port, and two output ports. When light is absent in the control port, the structure operates as a half adder and when light is present in the control port, it functions as a half subtractor. The operation of the structure is based on the phenomenon of constructive and destructive interference of light waves. The novelty of the proposed structure is that using a single control signal, both half adder and half subtractor operations can be realized. Since no nonlinear material has been used to design the structure, the power consumption of the structure is very low. Another advantage of the structure is that same materials have been used for all the rods which makes the fabrication process easier. The structure has been simulated by utilizing PWE and FDTD methods. Different performance parameters such as contrast ratio, rise time, delay time, fall time, response time, and bit rate for the designed structure have been obtained as 14.78 dB, 0.25 ps, 0.3 ps, 0.11 ps, 0.44 ps, and 2.27 Tb/s respectively. Due to its high contrast ratio, fast response time, high bit rate, and smaller dimension, the designed structure can be a promising candidate for realizing high speed optical integrated circuits.

engineering, electrical & electronic,optics,quantum science & technology
Single SOA based all-optical adder assisted by optical bandpass filter: Theoretical analysis and performance optimization

Jianji Dong,Songnian Fu,Xinliang Zhang,P. Shum,Liren Zhang,Jing Xu,Dexiu Huang

DOI: https://doi.org/10.1016/j.optcom.2006.09.053

IF: 2.4

2007-01-01

Optics Communications

Abstract:A simple and compact configuration of all-optical adders implemented with a single semiconductor optical amplifier (SOA) and optical bandpass filter (OBF) is presented in this paper. A comprehensive SOA model is put forward to investigate the output characteristics of the all-optical adders. The numerical simulation results demonstrate the influence of these key parameters, including input pulse peak power, pulsewidth, repetition rate, and OBF characteristics. Moreover some design rules are extracted for the proper selection of these parameters so as to ensure optimum performance. The obtained results confirm the feasibility of our configuration.
Design of all optical logic half adder based on holes-in-slab photonic crystal

Kamanashis Goswami,Haraprasad Mondal,Mrinal Sen

DOI: https://doi.org/10.1007/s11082-023-05848-9

IF: 3

2023-12-29

Optical and Quantum Electronics

Abstract:In this paper an all-optical half adder has been designed on a 2D photonic crystal slab having air holes in a hexagonal lattice pattern. The working principal of the device is based on beam interference. Multi-mode interference based Pi phase shifter been used in this design. Neither any nonlinear materials nor any extra bias signal has been incorporated in the structure. Plain wave expansion and Finite Difference Time Domain methods have been used for analyzing the band diagram of the structure and performance of the proposed device respectively. The SUM port provides 60%, 67%, and 1% transmittance whereas the CARRY port provides 4%, 1%, and 90% transmission for {0,1}, {1,0}, and {1,1} logic combinations respectively. Minimum contrast ratio has been obtained as 18 dB in SUM port and 12.5 dB in CARRY port. Therefore, it is expected that the proposed all-optical adder would be a potential candidate for future generation photonic integrated circuits.

engineering, electrical & electronic,optics,quantum science & technology
A novel proposal for an all optical combined half adder/subtractor

F. Pakrai,M. Soroosh,J. Ganji

DOI: https://doi.org/10.1007/s11082-022-03898-z

IF: 3

2022-07-14

Optical and Quantum Electronics

Abstract:In this paper we are going to propose a novel optical structure that can work as an optical combined half adder/subtractor. The proposed structure has 3 output ports. O1 is the common output port for adder and subtractor which can work as the sum/difference port of the proposed structure. O2 is the carry port of the optical adder and O3 is the borrow port of the optical subtractor. The working mechanism of the proposed structure is based on threshold switching, therefore three nonlinear ring resonators were combined with some optical waveguides. The maximum rise time of the proposed structure is 3 ps.

engineering, electrical & electronic,optics,quantum science & technology
Ultrafast all-optical half-adder and half-subtractor based on linear 2D photonic crystal

Sara Esmail Kordi,Reza Yousefi,Seyed Saleh Ghoreishi,Habib Adrang

DOI: https://doi.org/10.1007/s11082-021-03048-x

IF: 3

2021-07-01

Optical and Quantum Electronics

Abstract:This paper had designed and simulated new structures for realizing half-adder and half-subtractor based on a linear photonic crystal. For this purpose, first, some individual gates such as AND and XOR are proposed, and then by combining these gates in a single structure a half- adder and half-subtractor are performed. All the simulations are performed with the finite difference time domain (FDTD) method. The transient analysis of the structures shows that the response time of the proposed half-adder and half-subtractor are 0.27 ps and 0.19 ps, respectively. The total footprint of the final structures is also as little as 90.3 μm2\documentclass[12pt]{minimal}\usepackage{amsmath}\usepackage{wasysym}\usepackage{amsfonts}\usepackage{amssymb}\usepackage{amsbsy}\usepackage{mathrsfs}\usepackage{upgreek}\setlength{\oddsidemargin}{-69pt}\begin{document}$$\mu m^{2}$$\end{document} and the contrast ratio in a worse case is7.2 dB. The simulation results demonstrate the new structures have a considerably small size, ultrafast response time, and suitable contrast ratio in comparison with some previous works. Having these features make the introduced devices really usable for integration in the ultrafast optical integrated circuits.

engineering, electrical & electronic,optics,quantum science & technology
Silicon-on-Insulator-Based Compact Optical Demultiplexer Employing Etched Diffraction Grating

WH Wang,YZ Tang,YX Wang,HC Qu,YM Wu,T Li,JY Yang,YL Wang,M Liu

DOI: https://doi.org/10.1088/0256-307x/21/7/022

2004-01-01

Abstract:A compact optical demultiplexer with etched diffraction grating (EDG) is designed and fabricated on a silicon-on-insulator (SOI) material. Several 90degrees turning mirrors are used to bend the waveguides, and the size of the EDG-based demultiplexer is minimized to only 16 x 1.7 mm(2). The crosstalk is about -18 dB. The on-chip loss is about 18.2 dB, which is composed of about 16.9 dB excess loss and 1.3 dB diffraction loss. Measures to improve the performance are discussed.
Ultracompact All-Optical Full-Adder and Half-Adder Based on Nonlinear Plasmonic Nanocavities

Jingya Xie,Xinxiang Niu,Xiaoyong Hu,Feifan Wang,Zhen Chai,Hong Yang,Qihuang Gong

DOI: https://doi.org/10.1515/nanoph-2017-0035

IF: 7.5

2017-01-01

Nanophotonics

Abstract:Ultracompact chip-integrated all-optical half- and full-adders are realized based on signal-light induced plasmonic-nanocavity-modes shift in a planar plasmonic microstructure covered with a nonlinear nanocomposite layer, which can be directly integrated into plasmonic circuits. Tremendous nonlinear enhancement is obtained for the nanocomposite cover layer, attributed to resonant excitation, slow light effect, as well as field enhancement effect provided by the plasmonic nanocavity. The feature size of the device is <15 μm, which is reduced by three orders of magnitude compared with previous reports. The operating threshold power is determined to be 300 μW (corresponding to a threshold intensity of 7.8 MW/cm2), which is reduced by two orders of magnitude compared with previous reports. The intensity contrast ratio between two output logic states, “1” and “0,” is larger than 27 dB, which is among the highest values reported to date. Our work is the first to experimentally realize on-chip half- and full-adders based on nonlinear plasmonic nanocavities having an ultrasmall feature size, ultralow threshold power, and high intensity contrast ratio simultaneously. This work not only provides a platform for the study of nonlinear optics, but also paves a way to realize ultrahigh-speed signal computing chips.
Reconfigurable all optical half adder and optical XOR and AND logic gates based on 2D photonic crystals

Fariborz Parandin,M. Reza Malmir

DOI: https://doi.org/10.1007/s11082-019-2167-3

IF: 3

2020-01-20

Optical and Quantum Electronics

Abstract:The use of optical devices for high-speed data transmission has been considered for some time. Structures which can be used in optical integrated circuits are very important. Photonic crystals have been used as basic structures in the design of optical devices and especially logic devices. Considering the ability of these structures to design logic gates and circuits, it is expected to use them as base structures in the design of optical integrated circuits. In this research, an optical half-adder using two-dimensional photonic crystals was designed and simulated. One of the features of this circuit is the higher power difference in the high and low logic modes, which reduces errors in detecting these two values in the output. The circuit also has the ability to use the optical gates XOR and AND. In addition, it has a small structure that makes it suitable for use in optical integrated circuits.

engineering, electrical & electronic,optics,quantum science & technology
Design of All-Optical Logic Half-Adder Based on Photonic Crystal Multi-Ring Resonator

Yonatan Pugachov,Moria Gulitski,Omri Mizrahi,Dror Malka

DOI: https://doi.org/10.3390/sym15051063

2023-05-12

Symmetry

Abstract:In this paper, a novel design of an all-optical half-adder (HA) based on two two-ring resonators in a two-dimensional square-lattice photonic crystal (PC) structure without nonlinear materials is proposed. The all-optical HA comprises AND and XOR gates where each gate is composed of cross-shaped waveguides and two-ring resonators in a 2D square-lattice PC that are filled with silicon (Si) rods in silica (SiO2). The AND and XOR gates are analyzed and simulated using plane-wave expansion (PWE) and finite-difference time-domain (FDTD) methods. Simulation results show that light guiding inside the device functions as AND and XOR gates. Thus, the proposed device has the potential for use in optical arithmetic logic units for digital computing circuits. The structure comprises an optical AND gate and an optical XOR gate that were designed to work at the C-band spectrum. Results show that there is a clear distinction between logic states 1 and 0 with a narrow power range that leads to a better robust decision on the receiver side for minimized logic errors in the photonic decision circuit. Thus, the proposed HA can be a key component for designing a photonic arithmetic logic unit.

multidisciplinary sciences
High-speed compact silicon digital optical switch with slot structure

Simiao Xiao,Yubo Li,Yinlei Hao,Xiaoqing Jiang,Jianyi Yang

DOI: https://doi.org/10.1016/j.ijleo.2010.06.027

IF: 3.1

2011-01-01

Optik

Abstract:A high-speed compact silicon digital optical switch (DOS) is proposed in this paper. The direct electro-optic effect is applied by filling electro-optic polymer in the void slot of the branches, which compensates the limitation of silicon itself. The crosstalk of about 35dB and the insertion loss of 0.7dB is obtained, the switching speed is less than 1ps, and the whole device length can be shortened to 616μm even using the basic mode-evolving principle and a simple Y-type structure. Analysis also shows that the device has good fabrication tolerance and wavelength independence over the C-band.
Compact Inversely-Designed Vertical Coupler with Bottom Reflector for Sub-Decibel Fiber-to-Chip Coupling on Silicon-on-Insulator Platform

Shiang-Yu Huang,Stefanie Barz

2024-09-17

Abstract:Inverse design via topology optimization has led to innovations in integrated photonics and offers a promising way for designing high-efficiency on-chip couplers with a minimal footprint. In this work, we exploit topology optimization to design a compact vertical coupler incorporating a bottom reflector, which achieves sub-decibel coupling efficiency on the 220-nm silicon-on-insulator platform. The final design of the vertical coupler yields a predicted coupling efficiency of -0.35 dB at the wavelength of 1550 nm with a footprint of 14 {\mu}m x 14 {\mu}m, which is considerably smaller than conventional grating couplers. Its topology-optimized geometry can be realized by applying one full etch and one 70-nm shallow-etch process and the fabricability is also guaranteed by a minimum feature size around 150 nm. The proposed vertical coupler can further miniaturize photonic integrated circuits and enable highly-efficient networks between optical fibers and other photonic devices.

Optics,Applied Physics
Ultracompact all-optical full adders using an interference effect based on 2D photonic crystal nanoring resonators

Masoud Mohammadi,Vahid Fallahi,Mahmood Seifouri

DOI: https://doi.org/10.1007/s10825-020-01619-x

IF: 1.9828

2020-11-22

Journal of Computational Electronics

Abstract:Given the special place of hybrid logic circuits such as all-optical full adders in next-generation digital systems, a new kind of these structures using two-dimensional (2D) photonic crystals (2D-PC) is designed and simulated herein. The proposed structure is made of a hexagonal nanoring resonator (NRR), a coupling rod, and several waveguides. In this all-optical full adder, the mechanism of the interference effect in the PCs is used to simplify and minimize the structure. To make the structure flexible, the radius of the dielectric rod in the whole structure and the NRR are considered based on a lattice constant of 0.2a and 0.04a, respectively. The structure is operated at a wavelength of 1550 nm, considering the value of the power entering the waveguides and that exiting the Carry and Sum ports. To analyze the all-optical full adder, the plane-wave expansion method and finite-difference time-domain method are applied respectively to calculate the bandgap diagram and obtain the transmission and propagation of the optical field. In the proposed structure, the contrast ratio at the Carry and is been investigated in a unique and novel way, yielding values of 10.68 and 9.03 dB, respectively. In addition, the maximum and minimum response time for the Carry and Sum are obtained as 1.6 and 0.75 ps, respectively. The total footprint of the structure is about 183 µm2. Due to its ultracompact size, low power consumption, fast response time, and simple structure, this all-optical full adder is suitable for use in low-power optical integrated circuits.

engineering, electrical & electronic,physics, applied
Ultra-High Dynamic Extinction Ratio Electro-Optical Modulator with Coupled Microring on SOI Platform

Zhuo Cheng,Bigeng Chen,Chunlei Sun,Maoliang Wei,Shaoliang Yu,Lan Li,Hongtao Lin,Yunjiang Rao

DOI: https://doi.org/10.1109/acp55869.2022.10089079

2022-01-01

Abstract:A 5 th -order coupled microring electro-optical modulator with PIN structures is proposed and experimentally demonstrated on SOI integrated photonics platform. Ultra-high dynamic extinction ratio (ER) up to 60 dB is achieved benefiting from the high-order optical band-pass filter design. The device size on chip is only 400×220 μm 2 including electrodes and the driving voltage is 2.1 V corresponding to 0.23 W power consumption. Such integrated modulators would be promising in building compact and low-power distributed optical fiber sensing systems using low-background-noise optical pulses.

Compact Half Adder on SOI Platform with Inverse Design

Compact All-Optical Half Adder Based on Topology Optimization

Implementation of a Novel Optical Half-Adder

Ultra-compact and low delay time all optical half adder based on photonic crystals

Standardized Design: On-chip Diffractive Optical Logic Operation Units with Ultra-compact Structures

Design of an all-optical half adder based on photonic crystal ring resonator

Inverse-designed Metamaterials for On-chip Combinational Optical Logic Circuit

Design of Ultra-Compact and Multifunctional Optical Logic Gate Based on Sb2Se3-SOI Hybrid Platform

Photonic crystal based integrated system for half adder and half subtractor operations

Single SOA based all-optical adder assisted by optical bandpass filter: Theoretical analysis and performance optimization

Design of all optical logic half adder based on holes-in-slab photonic crystal

A novel proposal for an all optical combined half adder/subtractor

Ultrafast all-optical half-adder and half-subtractor based on linear 2D photonic crystal

Silicon-on-Insulator-Based Compact Optical Demultiplexer Employing Etched Diffraction Grating

Ultracompact All-Optical Full-Adder and Half-Adder Based on Nonlinear Plasmonic Nanocavities

Reconfigurable all optical half adder and optical XOR and AND logic gates based on 2D photonic crystals

Design of All-Optical Logic Half-Adder Based on Photonic Crystal Multi-Ring Resonator

High-speed compact silicon digital optical switch with slot structure

Compact Inversely-Designed Vertical Coupler with Bottom Reflector for Sub-Decibel Fiber-to-Chip Coupling on Silicon-on-Insulator Platform

Ultracompact all-optical full adders using an interference effect based on 2D photonic crystal nanoring resonators

Ultra-High Dynamic Extinction Ratio Electro-Optical Modulator with Coupled Microring on SOI Platform