Abstract:Due to their extremely high energy demand, data centers are directly supplied from a medium-voltage (MV) grid. However, a significant part of this energy is dissipated in the power supply chain since the MV is reduced step-by-step through multiple power conversion stages down to the chip-voltage level. In order to increase the efficiency of the power supply chain, the number of conversion stages must be substantially reduced. In this context, solid-state transformers (SSTs) are considered as a possible solution, as they could directly interface the MV AC grid to a 400 V DC bus, whereby server racks with a power consumption of several tens of kilowatts could be directly supplied from an individual SST. With a focus on the lowest system complexity, the SST, ideally, should be built as simple two-stage system consisting of an MV AC/DC power factor correction (PFC) rectifier stage followed by an isolated DC/DC converter. Accordingly, this paper focuses on the design and realization of a 25 kW, 3.8 kV single-phase AC to 7 kV DC PFC rectifier unit based on the 10 kV SiC MOSFETs. By simply adding an $LC$ circuit between the switch nodes of the well-known full-bridge-based pulse width modulated AC/DC rectifier, the integrated triangular current-mode concept is implemented, which only internally superimposes a large triangular current ripple on the AC mains current and, therefore, enables zero-voltage switching over the entire AC mains period. Special attention is paid to the realization of the MV inductors and their electrical insulation, the AC-input $LCL$ filter to limit electromagnetic interference emissions, and the challenges arising due to cable resonances when connecting the SST to the MV grid via an MV cable. Despite the large insulation distances required for MV, the realized 25 kW MV PFC rectifier achieves an unprecedented power density of 3.28 kW/L (54 W/ $\mathrm {in}^{3}$ ) and a full-load efficiency of 99.1%, determined using a calorimetric measurement setup, which is discussed in detail in the Appendix.

A High Power Density 75kva Air-Cooled SiC Intelligent Power Stage (IPS) As A Universal Building Block for Grid Applications

Design of CRM AC/DC Converter for Very High-Frequency High-Density WBG-based 6.6kw Bidirectional On-Board Battery Charger

Design And Demonstration Of A Sic-Based 800-V/10-Kv 1-Mw Solid-State Transformer For Grid-Connected Photovoltaic Systems

An Extremely High Efficient Three-Level Active Neutral-Point-Clamped Converter Comprising SiC and Si Hybrid Power Stages

A Three-Phase-Module-Parallel Si & SiC Hybrid Inverter with Smaller Filter Size and Low Cost

Efficiency Improvement of Grid Inverters With Hybrid Devices

An SiC MOSFET & Si Diode Hybrid Three-Phase High-Power Three-level Rectifier

High Performance SiC Power Module Based on Repackaging of Discrete SiC Devices

Sic Mosfet Zero-Voltage-Switching Svm Controlled Three-Phase Grid Inverter

A Three-Phase Isolated Building Block for High-Power Medium-Voltage Grid Applications

High Temperature Direct Double Side Cooled Inverter Module for Hybrid Electric Vehicle Application

Hardware Design of a 150kw/1500v All-SiC Grid-forming Photovoltaic Synchronous Generator (PVSG)

An All-SiC 15 kW/L 60 kW Multiplexing Converter for Electric Vehicles

A 380 V/50 Kvar SiC-SVG Achieving a Power Density of 1.652 Kvar/l with the Optimization of Heatsink and Output Filter Volume

A Novel Series-Parallel Design of the 3.6kv/400a SiC Austin SuperMOS

A 100kW Forced-Air-Cooled SiC MOSFET Converter Achieving a Power Density of 1.657kW/L and an Efficiency over 98.5%

99.1% Efficient 10 kV SiC-Based Medium-Voltage ZVS Bidirectional Single-Phase PFC AC/DC Stage

Extreme High Efficiency Enabled by Silicon Carbide (sic) Power Devices

An 800V/300 Kw, 44 Kw/l Air-Cooled SiC Power Electronics Building Block (PEBB).

A 1200 V/200 A Half-Bridge Power Module Based on Si IGBT/SiC MOSFET Hybrid Switch

Design, Development, and Testing of a Flexible Combined Heat and Power (F-CHP) System With 10-kV SiC MOSFET-Based Power Conditioning System (PCS) Converter