Arch Stone Bridge with Span Upper Column Disease Analysis and Reinforcement Scheme Research

Chuanqi Feng

2010-01-01

Abstract:Sizhuang No.2 big bridge is analyzed in an all-round way about its diseases and the causes are elaborated.Meanwhile the reinforcement scheme is put forward.It can provide reference for similar engineering.

What problem does this paper attempt to address?

Case Study on Stability Performance of Asymmetric Steel Arch Bridge with Inclined Arch Ribs

Xinke Hu,Xu Xie,Zhanzhan Tang,Yonggang Shen,Pu Wu,Lianfeng Song

DOI: https://doi.org/10.12989/scs.2015.18.1.273

2015-01-01

Steel and Composite Structures

Abstract:As one of the most common failure types of arch bridges, stability is one of the critical aspects for the design of arch bridges. Using 3D finite element model in ABAQUS, this paper has studied the stability performance of an arch bridge with inclined arch ribs and hangers, and the analysis also took the effects of geometrical and material nonlinearity into account. The impact of local buckling and residual stress of steel plates on global stability and the applicability of fiber model in stability analysis for steel arch bridges were also investigated. The results demonstrate an excellent stability of the arch bridge because of the transverse constraint provided by transversely-inclined hangers. The distortion of cross section, local buckling and residual stress of ribs has an insignificant effect on the stability of the structure, and the accurate ultimate strength may be obtained from a fiber model analysis. This study also shows that the yielding of the arch ribs has a significant impact on the ultimate capacity of the structure, and the bearing capacity may also be approximately estimated by the initial yield strength of the arch rib.
Stability Analysis of Yinxian Second Bridge

WANG Xiao-zhou,LI Hui,XIE Xu

DOI: https://doi.org/10.3969/j.issn.1001-5132.2006.02.023

2006-01-01

Abstract:In this paper,a CFST(concrete filled steel tubular) arch bridge,YinXian Second Bridge,is analyzed using linear and nonlinear methods.Both the material and geometric nonlinear properties are taken into account in the nonlinear analysis.Some conclusions are reached through calculations for different load cases.
Disease Analysis and Reinforcement of Concrete Bridge Substructure

He Xiaoyang,Xiang Yiqiang,Xing Cheng

DOI: https://doi.org/10.3969/j.issn.1674-0696.2013.sup.1.19

2013-01-01

Abstract:Main types of the pier,abutment and foundation in substructure of RC or PC bridges in China were summarized respectively.It was pointed out that the main diseases in substructure of concrete bridges were differential settlement of foundations,insufficient carrying capacity,durability diseases of reinforced concrete,cracking of concrete pier columns,bent caps and abutments etc..In allusion to the concrete pier,abutment and foundation,the causes and mechanisms of these diseases were analyzed from the design,construction,maintenance and operation of bridges.The relevant maintenance and strengthening methods were also discussed,such as the foundation enlargement method,adding pile method and artificial foundation reinforcement method for concrete and RC pier or abutment foundation;the method of RC columns reinforced by reinforced concrete hoop or FRP for piers,the reinforcement method of pasting steel strips or plates,the method of external prestressed reinforcement and additional support method,etc.for RC bent caps;the method of reducing load,the method of reducing filling height by adding approach spans,the support beam method and the reinforcement method of installing auxiliary retaining wall,etc.for RC abutments.
Numerical Analysis of Ultimate Strength of Concrete Filled Steel Tubular Arch Bridges

Xie Xu,Chen Heng-zhi,Li Hui,Song Shi-rui

DOI: https://doi.org/10.1631/jzus.2005.a0859

2005-01-01

Abstract:The calculation of ultimate bearing capacity is a significant issue in the design of Concrete Filled Steel Tubular (CFST) arch bridges. Based on the space beam theory, this paper provides a calculation method for determining the ultimate strength of CFST structures. The accuracy of this method and the applicability of the stress-strain relationships were validated by comparing different existing confined concrete uniaxial constitutive relationships and experimental results. Comparison of these results indicated that this method using the confined concrete uniaxial stress-strain relationships can be used to calculate the ultimate strength and CFST behavior with satisfactory accuracy. The calculation results are stable and seldom affected by concrete constitutive relationships. The method is therefore valuable in the practice of engineering design. Finally, the ultimate strength of an arch bridge with span of 330 m was investigated by the proposed method and the nonlinear behavior was discussed.
Approach for Analyzing the Ultimate Strength of Concrete Filled Steel Tubular Arch Bridges with Stiffening Girder

Zhang Zhi-cheng,Xie Xu,Zhang He,Chen Heng-zhi

DOI: https://doi.org/10.1631/jzus.2007.a0682

2007-01-01

Abstract:A convenient approach is proposed for analyzing the ultimate load carrying capacity of concrete filled steel tubular (CFST) arch bridge with stiffening girders. A fiber model beam element is specially used to simulate the stiffening girder and CFST arch rib. The geometric nonlinearity, material nonlinearity, influence of the construction process and the contribution of prestressing reinforcement are all taken into consideration. The accuracy of this method is validated by comparing its results with experimental results. Finally, the ultimate strength of an abnormal CFST arch bridge with stiffening girders is investigated and the effect of construction method is discussed. It is concluded that the construction process has little effect on the ultimate strength of the bridge.
Finite-element Analysis for Nonlinear Stabilities of Concrete-filled Steel Tubular Arch Bridges

JIAO Yu-Feng,YI Jian-Long,CHEN Shui-Fu

2008-01-01

Abstract:Owing to the limitation of establishing finite element model of concrete-filled steel tubular(CFST) arch bridge,the more precision model has been put forward.Namely the outer steel tubes,the inner concrete and the reinforcing steel bars have their own elements.Using this method,a CFST arch bridge's deflection curve under different load is obtained considering the material and geometric nonlinearity.The computed results are in agreement with the test data.The result shows that the method used in this paper has better adaptability and definition.
Analysis and strengthening of superstructure diseases of concrete bridges in China

Y. Q. Xiang,X. Zhang,Y. Xing

DOI: https://doi.org/10.1201/b17063-317

2014-01-01

Abstract:In this paper, the main types of the superstructure of concrete bridges in China are summarized. It is pointed out that the main defects in the superstructure of concrete bridges in China are penetration of chloride ion, corrosion of steel bar, overlarge deformation, and cracking of main beams or box girders. Based on the various defects existing in different types of bridge superstructures, the causes and mechanisms of these defects are analyzed from the view of design, construction, material, and service conditions. The relevant maintenance and strengthening countermeasures are put forward, such as crack grouting, shotcreting reinforcement, pasting steel reinforcement plates on surface of beam and box girder, pasting carbon fiber or other fiber materials, increasing the cross section of beam and box girder, adding external prestressed tendons, changing the structural system, adding main girders or strengthening lateral connection among main girders, and other strengthening methods. These strengthening methods aim to improve the durability and bearing capacity of bridges, extend service life of bridges, and assure the integral performance of bridges in the whole life cycle.
Analysis and strengthening of substructure diseases of concrete bridges in China

Y. Q. Xiang,X. Y. He,C. Xing,H. Kordestani,L. H. Shao

DOI: https://doi.org/10.1201/b17063-318

2014-01-01

Abstract:In this paper the major types of piers, abutment and foundation in substructure of RC or PC bridges in China are summarized. The main types of defects occurring in substructure of concrete bridges including uneven settlement of foundation, lower carrying capacity, durability defects of reinforced concrete and cracking of concrete pier columns as well as abutments and cap beams have been pointed out. In addition to the concrete pier, abutment and foundation, the causes and mechanisms of these defects were analyzed from different points of view such as design, construction, maintenance and operation management. The relevant maintenance and strengthening methods were discussed and put forward, such as the foundation enlargement method, adding pile method and artificial foundation reinforcement method for concrete and RC pier or abutment foundation, the method of RC pier columns reinforced by RC hoop or FRP for piers, the reinforcement method of pasting steel strip or plate, the method reinforced by external prestressed tendons and additional support columns method for RC cap beams, the method of reducing load, the method of reducing fill height by adding numbers of approach spans, the support beam method and the method reinforced by auxiliary retaining wall for RC abutments. It is possible to recover the function of the RC or PC bridges and enhance their durability and load carrying capacity by employing corresponding maintenance and strengthening measures. At the same time, vehicle overload should be strictly limited according to the structural safety matters.
Stress Performance Analysis of Special-shaped Arch Bridge with Longitudinal Linkage

Yong-gang SHEN,Yi-qiang XIANG,Ming-zhong YAN,Wei-guo ZHU

DOI: https://doi.org/10.3969/j.issn.1004-4655.2007.05.008

2007-01-01

Abstract:The idea can meet with the bridge aesthetics better that is to install the longitudinal linkage between 2 special-shaped arches.Through the project calculation of Jigeng Bridge in Nantong,the structure internal force of arch rib was changed greatly,especially the shearing force of the contiguous arch rib sections was strengthened evidently after installing the longitudinal linkage.Meanwhile,the external stability of the whole arch rib was lowered but the total rigidity of the whole bridge and natural frequencies were improved.The results showed that the idea should be adopted in the practical design of special-shaped arch bridge.
Behaviour Analysis of Prestressed Concrete Deck-Tied Arch Bridge

yi qiang xiang,li chang zhang,qiang qiang wu

DOI: https://doi.org/10.4028/www.scientific.net/AMR.671-674.952

2013-01-01

Abstract:The prestressed concrete deck-tied arch bridge doesn't only have a long span, good appearance and economy, but also have the characteristics of low requirements to the foundation. It changes traditional tied arch bridge into deck-tied arch bridge, which looks like sunflower-shaped arch and prestressed steel strands are embedded in box girder on the top of the arch. Taking Yingbin Bridge as engineering background, the reasonable analysis model was established and behaviour of the bridge under design load was analyzed. The results shown that the design project is reasonable, prestressing force embedded in box girder can balance horizontal thrust in arch bridge effectively, improving the internal force of the main arch ring.
DESIGN AND ANALYSIS OF ARCH TOWER CABLE-STAYED BRIDGE

Ye Zhengwei,Xiang Yiqiang

2009-01-01

Abstract:Tengfei Bridge in Linyi City is a 45+55 m elliptic arch tower double cable planes cable-stayed bridge,very beautiful owing to its light structure and new shape.The structure,method of design and analysis,also the main calculate results as well,are presented,which could be used for reference in design of city bridges of esthetical effect needs.
Study on Design and Maintenance Strategy of Concrete Bowstring Arch Bridge Based on Given Service Life of Structure

Li Yi,Wei Hua,Guo Zhong,Chen Baochun,Xiang Yiqiang

DOI: https://doi.org/10.3969/j.issn.1009-7716.2012.02.038

2012-01-01

Abstract:Aiming at the fault and maintenance strategy of concrete bowstring arch bridge,the article analyzes the results based on the grades and vulnerability of components for the bowstring arch bridge from the design and maintenance ideas of the given service life of structure,and looks for the components not only important but also easily damaged in the structures.These components are firstly and importantly plaid attention in the selection of bridge design and maintenance order for realizing the special maintenance.The security and the economy are also weighed to reach the aim of reducing the maintenance cost and efficiently prolonging the service life of bridge.
Maintenance strategy and method of concrete arch bridges in life cycle ii: performance degradation analysis and repair reinforcement methods

Y. Xiang,X. Ye,Qiangqiang Wu

2013-01-01

Abstract:This paper emphatically analyzes some existing problems in planning, design, construction, operation, and maintenance of concrete arch bridges, including insufficient load bearing capacity caused by uneven settlement of bridge piers, horizontal displacement, change of temperature, overload, lower design load level in original bridge design, and poor durability and performance degradation of concrete structures caused by chloride permeability, steel bar corrosion, carbonization, cover spalling of concrete, aging cracking at the PE protective layer of suspenders, rain leakage, and corrosion of concrete arches etc. From the safety, applicability, durability, economy, environmental protection, and sustainability considerations in life cycle of bridges, the appropriate maintenance strategies and methods of arch bridges are explored for the different objectives and performance levels. It has certain theoretical significance and practical engineering value. Xiang et al.: MAINTENANCE STRATEGY AND METHOD OF CONCRETE ARCH BRIDGES IN LIFE CYCLE II: PERFORMANCE DEGRADATION ANALYSIS AND REPAIR REINFORCEMENT METHODS 766
Study on Stone Arch Bridge Performance Assessment and Reinforcement Measures

Shou-kui HE

2007-01-01

Abstract:For scientific selecting reinforcement measures of stone arch bridge,set up operation situation evaluation model,make performance fuzzy assessment combine with past operation records of stone arch bridge,form decision tree of reinforcement measures.
Multi-rib Arch Bridge Strengthened by Stayed-Cable and Field Test

Yiqiang Xiang

DOI: https://doi.org/10.1007/978-3-030-29227-0_90

2019-01-01

Abstract:With the increase of traffic volume and load, the carrying capacity of the early constructed reinforced concrete multi-ribbed arch bridges are obviously lower, it is necessary to take various measures to strengthen them and enhance bearing capacity of these bridges. This paper proposes a reinforcement method by adding cable tower at the two ends abutments of the arch bridges and the inclined cables to improve behavior of the multi-rib arch bridge. The main idea is that additional bridge towers are set on both sides of the single span ribbed arch bridge abutment to hang stayed cables. Taking a typical reinforced concrete multi-rib arch bridge-Baibu Bridge as engineering background, the design of strengthening project was given. The analysis and field load test of the bridge were finished. The comparison between spatial finite element analysis results and field bridge test values of strengthened bridge has good agreement. It shows the validity of the proposed strengthening method for the rib arch bridge and improves effectively the bearing capacity of arch bridges.
Maintenance strategy and method of concrete arch bridges in life cycle i: performance levels and performance requirements

Y. Xiang,Qiangqiang Wu,Kun Chen

2013-01-01

Abstract:Concrete arch bridges are one of the common types for highway bridges. They have advantages of graceful line shape and beautiful appearance, good behaviour and large spanning capacity. As far as the reinforced concrete arch bridges (or combinedsystem arch bridges) are concerned, this paper describes the durability problems of the designed and constructed concrete bridges and related research advances in China in past 30 years. It is pointed out that the performance of structure life-cycle should include safety, suitability, durability and environmental protection (sustainability and reparability). Performance requirements of bridges in three different performance levels are discussed by comprehensively considering these factors of safety, serviceability, durability, environmental protection, bridges location and importance. It lays the foundation for structural design, maintenance and strengthening, based on performance in life-cycle. Xiang et al.: MAINTENANCE STRATEGY AND METHOD OF CONCRETE ARCH BRIDGES IN LIFE CYCLE I: PERFORMANCE LEVELS AND PERFORMANCE REQUIREMENTS 756
Analysis of the Existing Reinforced Concrete Rigid Frame Arch Bridge Strengthened with Arch and Cable System

Xiang-yang CHEN,Jin-feng WANG,Jian-jiang WANG,Yi-qiang XIANG

DOI: https://doi.org/10.3969/j.issn.1002-0268.2005.11.029

2005-01-01

Journal of Highway and Transportation Research and Development

Abstract:The project and method of the existing rigid frame arch bridge reinforced by changing arch structural system into arch and cable system is presented.Based on a typical bridge,the analysis of the static behavior of the bridge before and after the strengthening is preformed.The results show that the mid-span bending moment and deflection of the reinforced bridge are reduced obviously and the capacity of carrying load is greatly improved.It is proved that it is an effective method to reinforce the existing rigid frame arch bridges built early and enhance its capacity of carrying load.It has definite theory significance and practical engineering value.Constructional procedure of the bridge reinforced by changing arch structural system into arch and cable system and the reasonable cable force is also presented.
Reinforcement Analysis of an Old Multi-Beam Box Girder Based on a New Embedded Steel Plate (ESP) Strengthening Method

Yuliang He,Kai Wang,Zongyong Cao,Peijuan Zheng,Yiqiang Xiang

DOI: https://doi.org/10.3390/ma15124353

IF: 3.4

2022-01-01

Materials

Abstract:Multi-beam box girder bridges have been applied widely throughout the world for many years. However, the cracking of longitudinal joints between the box girders always leads to reflective cracking of the bridge decks during the service period and thus finally affects the safety and durability of the actual bridges. An embedded steel plate (ESP) strengthening method was presented by introducing carbon-A/-B glue to reinforce the longitudinal joints of old multi-beam box girder bridges for this problem. In order to evaluate the feasibility of the proposed method for actual bridges, an old multi-beam box girder bridge was reinforced, and structural parameters including strain, frequency, and deflection were obtained by adopting field tests before and after strengthening. In addition, the corresponding finite element (FE) model of the background bridge was also set up using ANASYS 18.0 to analyze the strengthening process. Analysis results of the actual bridge and FE model indicate that structural stiffness and load lateral transferring performance between the box girders were enhanced after ESP strengthening. Therefore, this proposed strengthening method can be used to improve the mechanical performance of multi-beam box girder bridges and provide reference for such bridge reinforcement.
Reinforced Concrete Multi-Rib Arch Bridge Strengthened by Changing Structural System

Yiqiang Xiang,Bishnu Gupt Gautam

DOI: https://doi.org/10.1007/978-3-030-01932-7_6

2018-01-01

Abstract:Before and after the 1980s, the China built many reinforced concrete multi-rib arch bridges. With the increase of traffic volume and load, the carrying capacity of the multi-rib arch bridges are obviously lower, it is necessary to take various measures to strengthen and enhance bearing capacity of these bridges. This paper proposes a reinforcement method by adding cable towers in two ends abutment of arch bridges and the inclined cables to improve behavior of RC multi-rib arch bridge. The main idea is that additional bridge towers are set on two side abutments of the RC rib arch bridge with single span to hang stayed cables. Newly-casting RC longitudinal beams are set in two sides of the bridge and the transverse prestressed steel tendons with \( 4{\upvarphi }^{\text{j}} 15.24 \) steel strands on the both sides of every cross beam were stretched, which are wrapped by the steel tubes and connected with longitudinal beams, to enhance the integrality and stiffness of the multi-rib arch bridge. Then, the longitudinal beams of each side of arch bridge are supported by using stayed cables through the cable tower. Comparison of the values gained by space finite element and field test confirmed that the proposed method for strengthening the rib arch bridge and enhancing the bearing capacity is effective.
Progressive Collapses Simulation And Importance Assessment Of Stone Arch Bridge

Xiao Lu,Xin-Zheng Lu,Lie-Ping Ye,Xu-Chuan Lin

2010-01-01

Abstract:With the increasing accidents of structures caused by human errors, terrorist attacks or nature disasters in recent years, disaster-prevention and hazard-mitigation for structures have aroused the concern of engineers, especially the safety of infrastructures. Based on a traditional 3-span stone arch bridge, this paper establishes a 3-D finite element (FE) model of the stone arch bridge with the general-purpose finite element program-MSC.MARC. The process of the collapse is simulated with the contact algorithm and the deactivation of elements, and the possible reasons of the collapse are analyzed. Furthermore, the importance of different components of the stone arch bridge is indexed with the conception of the generalized structural stiffness, so as to identify the most critical regions of the stone arch bridge. The predicted critical regions are verified to be correct and reasonable via limit analysis, which provides references for the design, construction and maintenance of arch bridges.

Arch Stone Bridge with Span Upper Column Disease Analysis and Reinforcement Scheme Research

Case Study on Stability Performance of Asymmetric Steel Arch Bridge with Inclined Arch Ribs

Stability Analysis of Yinxian Second Bridge

Disease Analysis and Reinforcement of Concrete Bridge Substructure

Numerical Analysis of Ultimate Strength of Concrete Filled Steel Tubular Arch Bridges

Approach for Analyzing the Ultimate Strength of Concrete Filled Steel Tubular Arch Bridges with Stiffening Girder

Finite-element Analysis for Nonlinear Stabilities of Concrete-filled Steel Tubular Arch Bridges

Analysis and strengthening of superstructure diseases of concrete bridges in China

Analysis and strengthening of substructure diseases of concrete bridges in China

Stress Performance Analysis of Special-shaped Arch Bridge with Longitudinal Linkage

Behaviour Analysis of Prestressed Concrete Deck-Tied Arch Bridge

DESIGN AND ANALYSIS OF ARCH TOWER CABLE-STAYED BRIDGE

Study on Design and Maintenance Strategy of Concrete Bowstring Arch Bridge Based on Given Service Life of Structure

Maintenance strategy and method of concrete arch bridges in life cycle ii: performance degradation analysis and repair reinforcement methods

Study on Stone Arch Bridge Performance Assessment and Reinforcement Measures

Multi-rib Arch Bridge Strengthened by Stayed-Cable and Field Test

Maintenance strategy and method of concrete arch bridges in life cycle i: performance levels and performance requirements

Analysis of the Existing Reinforced Concrete Rigid Frame Arch Bridge Strengthened with Arch and Cable System

Reinforcement Analysis of an Old Multi-Beam Box Girder Based on a New Embedded Steel Plate (ESP) Strengthening Method

Reinforced Concrete Multi-Rib Arch Bridge Strengthened by Changing Structural System

Progressive Collapses Simulation And Importance Assessment Of Stone Arch Bridge