Abstract:Due to the varying cooling conditions within different internal areas, there is a notable disparity in the cooling rates. This discrepancy has resulted in severe elemental segregation and the formation of coarse M C phases in the Φ508 mm GH4151 superalloy ingot, which has undergone triple smelting (VIM + ESR + VAR). These factors have had detrimental effects on the stability of the alloy structure. The solidification segregation, microstructure evolution, and secondary phase precipitation behaviors of GH4151 alloy under a wide cooling rate range were studied through Differential Scanning Calorimetry (DSC), in situ observations with High-Temperature Confocal Laser Scanning Microscopy (HT-CLSM), Directional Solidification (DS), and Computational Fluid Dynamics (CFD). The results show that the solidification path of GH4151 can be summarized as (1)L → γ (1334.6 °C); (2) L → γ + M C (1281 °C and 1258 °C); (3)L → γ + M C + γ/γ' + Laves (1152 °C); (4)L → γ + M C + γ/γ' + Laves+ M 2 B (1084 °C), where MC, γ/γ', Laves, and M 2 B are the main precipitate types during the solidification process. Mo, Nb, and Ti are the main dendritic segregation elements. Due to the reverse diffusion of solute elements under low cooling rates, the element segregation presents an increasing and then decreasing trend with the increase in cooling rate. The maximum segregation rate occurs at 24 °C/min. The cooling rate dramatically influences the morphology of the solid-liquid interface. The prediction formulas for PDAS and SDAS of GH4151 alloy under slow cooling conditions are λ 1 = 1137.1· V -0.25 · G -0.5 and λ 2 = 153.6· V c -0.32 respectively. Similarly, with the increase of solidification speed, the size of γ' phase, Laves phase, γ/γ' phase, and M C gradually decreases. When the cooling rate exceeds 12 °C/min, the large blocky M C phase evolves into elongated bars. The cooling rate from the center to the surface of the Φ508 mm VAR ingot ranges from 5 to 20 °C/min, with the standout being that the fastest cooling rate at the edge is about 48 °C/min.

Effect of the Solidification Rate on the Microstructure of Directionally Solidified Al-17.5wt%In Alloy in High Temperature Gradient

Effect of Directional Solidification Methods on Solid Solution Window in Ni-based Single-Crystal Superalloy

Microstructure and Microsegregation in A Ni-Based Single Crystal Superalloy Directionally Solidified under High Thermal Gradient

Influence of directional solidification variables on the microstructure and crystal orientation of AM3 under high thermal gradient

Microstructure evolution and solidification behaviour of Nb–16Si–22Ti–2Cr–2Al–6Hf alloy processed by directional solidification

Effect of the cooling rates on the microstructure and segregation characteristics in directionally solidified GH4151 superalloy

Solidification Characteristics and As-Cast Microstructure of Rhenium-Containing Single Crystal Superalloys under High Thermal Gradient Directional Solidification

Effect of Cooling Rate on Solidification Parameters and Microstructure of Al-7Si-0.3Mg-0.15Fe Alloy

Photoemission Studies of High-Tc Superconductors: The Superconducting Gap

Effect of Growth Rate on Microstructure and Mechanical Properties in a Directionally Solidified Nb-silicide Base Alloy

Effects of Solidification Rates on Microstructure Refinement and Elemental Distribution of Ti44Al6Nb1.0Cr2.0V0.1B0.15Y Alloy by Rapid Solidification

Phase-Field Simulation of Directional Solidification Microstructure Evolution in A Binary Alloy

Effect of cooling rate on microstructure and mechanical properties of Mg-9Gd-4Y-1Zn-1Al alloy

Dynamic precipitation and its effect on microstructure of 2195 Al–Li alloy during medium/high temperature deformation

The Effect of Cooling Rate on the Microstructure and Mechanical Properties of Mg–Zn–Gd-based Alloys

Dependence of microstructure and mechanical properties on solidification condition of directionally solidified Zn-55Al-1.6Si alloys

Microstructure and Microtexture Evolution of Dynamic Recrystallization of a Ni-based Superalloy under High-Throughput Gradient Thermal Compression

Effect of Withdrawal Rate on Microstructure and Mechanical Properties of a Directionally Solidified NiAl-based Hypoeutectic Alloy Doped with Trace Hf and Ho

Investigation of macro/microstructure evolution and mechanical properties of directionally solidified high-Nb TiAl-based alloy

Effects of Composition and Growth Rate on the Microstructure Transformation of Β-Rods/lamellae/α-rods in Directionally Solidified Mg-Li Alloy

Solidification Behavior of Ni-based Superalloy at Different Cooling Rates