Abstract:A titanium matrix composite reinforced with 2.6vol% in-situ TiC particles is fabricated by mechanically blending a TiH2 powder and 1vol% carbon nanotubes (CNTs) followed by induction heating, holding and hot extrusion of the compacts of the powder blend. This fabrication process involves dehydrogenation, in situ chemical reactions and powder consolidation, and takes less than 15min in total, being much more rapid than the conventional powder metallurgy processes involving dehydrogenation and powder compact sintering steps. This process also leads to formation of a novel Ti matrix composite microstructure consisting of a matrix of coarse α-Ti blocks and ultrafine α-Ti grains and in-situ formed near-spherical TiC particles. With increasing the holding and extrusion temperature from 1000 to 1200°C, the sizes of the coarse α-Ti blocks increased from1.5–5.5µm in width and 12.5–26µm in length to 4.5–13µm in width and 13–35µm in length, the sizes of the ultrafine α-Ti grains increased from 140 to 250nm to 350–500nm, and the average size of in-situ TiC particles increased from 1.2 to 4.6µm. These microstructural changes result in little change of the average yield strength (895–905MPa) and fracture strength (1045–1117MPa), but a clear increase of the elongation to fracture from 1.6% to 3.3%. The contributions and influence of the microstructural constituents: α-Ti blocks, ultrtafine α-Ti grains and TiC particles, to the mechanical properties and fracture behavior of the composite are discussed.

Fabrication of TiC Particles Dispersion-reinforced Aluminum Matrix Composite by In-situ Synthesis Technique

In Situal3ti–al2o3 Intermetallic Matrix Composite: Synthesis, Microstructure, and Compressive Behavior

Preparation, Microstructure and Mechanical Properties of In-Situ TiC/Al–Si–Fe Aluminum Matrix Composites

Microstructure and property of Al/TiC composites prepared by reaction synthesis

Microstructure and Compressive Properties Ofin SituSynthesized TiC/Ti Composites

Strengthening Effects of Tic Particles and Microstructure Refinement in in Situ Tic-Reinforced Ti Matrix Composites

Fabrication of an In-Situ Ti-2.6vol%Tic Metal Matrix Composite by Thermomechanical Consolidation of A Tih2-1vol%Cnts Powder Blend

Microstructure, Mechanical Properties and Fracture Mechanism of Ti2AlC Reinforced AZ91D Composites Fabricated by Stir Casting

In-situ TiC/Ti composites based on Ti 2 AlC–Ti system: Reaction process, microstructure, and mechanical properties

Microstructure and Tensile Properties of in Situ Synthesized (Tib+tic)/ti-6Al-4v Composites

Wear Behavior of In-Situ TiC Particles Reinforced Aluminum Matrix Composite

Microstructure and Mechanical Properties of in Situ Synthesised (Tic+tib)/ti-6Al-4v Composites Prepared by Powder Metallurgy

Study on in Situ Synthesis of TiC Particle Reinforced Iron Matrix Composite

Microstructure and Mechanical Properties of Ti2AlC Particle and In-Situ TiAl3 Reinforced Pure Al Composites

Microstructure, mechanical properties and strengthening mechanism of in-situ synthesized TiC/6061 nanocomposites

Microstructure and Phase Evolution Characteristics of the In Situ Synthesis of TiC-Reinforced AZ91D Magnesium Matrix Composites

Investigation on microstructure and properties of TiC0.5-Al2O3/Cu composites fabricated by a novel in-situ reactive synthesis

Synthesis of Al7075/TiB2-Al2O3 In-Situ Hybrid Composite by Stir Casting Method

Microstructure and compressive properties of in situ synthesized (TiB + TiC)/Ti composites

Microstructural characterization and mechanical properties of (TiC+TiB)/TA15 composites prepared by an in-situ synthesis method

Processing, Microstructure and Mechanical Properties of Ti6Al4V Particles-Reinforced Mg Matrix Composites