Abstract:Micro thermoelectric generator (μ-TEG) attracts more and more attention due to its small size and high power density. Many two-dimensional thermoelectric materials with high performance have facilitated the development of μ-TEG. However, the performance of μ-TEG fabricated by these great thermoelectric materials is significantly degraded due to size effect, interfacial effects (include contact effect and boundary effect) and structure effect. To accurately assess the performance degradation degree from material to μ-TEG and guide the device fabrication, an experiment-verified mathematical model considering interfacial and size effects is proposed. Firstly, the phonon/electron temperature distribution in thermoelectric leg of μ-TEG is analyzed to investigate the device-level thermoelectric properties of material. Then based on the device-level thermoelectric properties, the actual power generation performance model of μ-TEG is established to conduct the influence analysis of these effects (boundary, size, contact and structure effects) on material and device. Finally, the thermoelectric leg thickness ( H te ) is optimized to realize optimal power generation. The study results reveal that boundary and size effects weaken the device-level thermoelectric properties, and the reduction trend is more obvious when H te is smaller, especially when H te ≤ 20 μm. The decrease from the material intrinsic figure of merit ( (ZT) m ) to the device figure of merit ( (ZT) D ) is owing to the boundary effect, structure effect and contact effect, and the dominant factor of this decrease changes from structure effect ( H te <7 μm)to contact effect ( H te ≥ 7 μm) as H te increases, which points to a main optimization direction for (ZT) D for different H te . As for contact effect, the electrical contact resistivity ( r e,c ) has a more significant impact on weakening the performance of μ-TEG than thermal contact resistivity ( r k,c ), and their optimization goals are explored ( r e,c ≤ 5.1 × 10 −12 Ω·m 2 , r k,c ≤ 9.3 × 10 −8 K·m 2 /W). At given electrical and thermal contact resistivity, there exists an optimal H te for achieving the optimal power generation ( P opt ) and a large range of H te for achieving 95% P opt , and the optimal H te increases with increasing electrical and thermal contact resistivity. This study can reduce the processing difficulty and save time and economic costs of μ-TEG fabrication, which can avoid the blind fabrication of μ-TEG.

Extends the Refrigeration Limit of a Thermoelectric Element Through Micro/Nano Scale Cooling

Advancing Cryogenic Electronic Cooling: A Case Study on Embedded Manifold Microchannels in Micromachined Joule-Thomson Coolers

Design Optimization of Thermoelectric Cooling Systems for Applications in Electronic Devices

Performance enhancement of a novel thermoelectric self-cooling system for electronic devices

Simultaneous optimization of cooling temperature difference and efficiency for multi-stage thermoelectric device

Investigation of a novel separately-configured micro-thermoelectric cooler to enabling extend application scope

Optimized Thermoelectric Cooler Performance by the Structure-Matching Design of Asymmetrical p/n-Type Legs

A Model to Evaluate the Device-Level Performance of Thermoelectric Cooler with Thomson Effect Considered

Characterizing the thermoelectric cooling performance across a broad temperature range

Investigation of the impact of the thermoelectric geometry on the cooling performance and thermal—mechanic characteristics in a thermoelectric cooler

Irreversibility of thermoelectric cooling model: Newtonian linear heat transfer and finite time thermodynamics

Thermodynamic Analysis of TEG-TEC Device Including Influence of Thomson Effect

Enhancement of thermoelectric cooling by hot-end electroluminescence

Performance degradation analysis and fabrication guidance of μ-TEG from material to device

Efficient Thermoelectric Cooler for Localized Cooling in Electronic Devices

Inhomogeneous thermal conductivity enhances thermoelectric cooling

Transient Supercooling Analysis of an I-type Thermoelectric Cooling Element by the Experiment

Improved Thermoelectric Cooling Based on the Thomson Effect

A novel thermoelectric cooler with pores for improved thermal performance

Optimization of segmented thermoelectric devices composed of high-temperature thermoelectric material La2Te3

Performance Investigation and Optimization of an L-type Thermoelectric Generator