Abstract:An onset condition of gas entrainment (GE) due to free surface vortex has been studied to establish a design of fast breeder reactor with higher coolant velocity than conventional designs, because the GE might cause the reactor operation instability and therefore should be avoided. The onset condition of the GE has been investigated experimentally and theoretically, however, dependency of the vortex type GE on local geometry configuration of each experimental system and local velocity distribution has prevented researchers from formulating the universal onset condition of the vortex type GE. A real scale test is considered as an accurate method to evaluate the occurrence of the vortex type GE, but the real scale test is generally expensive and not useful in the design study of large and complicated FBR systems, because frequent displacement of inner equipments accompanied by the design change is difficult in the real scale test. Numerical simulation seems to be promising method as an alternative to the real scale test. In this research, to evaluate the applicability of the numerical simulation to the design work, numerical simulations were conducted on the basic experimental system of the vortex type GE. This basic experiment consisted of rectangular flow channel and two important equipments for vortex type GE in the channel, i.e. vortex generation and suction equipments. Generated vortex grew rapidly interacting with the suction flow and the grown vortex formed a free surface dent (gas core). When the tip of the gas core or the bubbles detached from the tip of the gas core reached the suction mouth, the gas was entrained to the suction tube. The results of numerical simulation under the experimental conditions were compared to the experiment in terms of velocity distributions and free surface shape. As a result, the numerical simulation showed qualitatively good agreement with experimental data. The numerical simulation results were similar to the experimental results in terms of the shape of free surface dent and the velocity distribution around the vortex, although the GE itself was not completely reproduced due to a lack of enough mesh partition. After confirming the applicability of the numerical simulation to the GE evaluation, several parameters, such as suction velocity and a configuration around suction mouth, were numerically examined to evaluate their influence on the GE. The tendencies of the GE occurrence enhanced by larger suction velocity or suction mouth on bottom surface enhance occurrence of the GE were obtained from the simulation results. These simulation results implied that the numerical simulation has enough potential to be used for the design work.

Numerical Study of the Energy Separation in the Novel-Designed Vortex Tube

Experimental Study Of The Energy Separation In A Vortex Tube

Numerical analysis and an approach for optimization of the Ranque–Hilsch vortex tube for a compressible flow

The Experimental Study on Different Ratios of Vortex Tube Hot End Pressure and Cold End Pressure

Quantitative Analysis of Energy Transfer and Separation in Vortex Tubes: Factors and Empirical Insights

Numerical analysis for the thermal performance and flow separation in the vortex tube with different design of flow control valve

Experimental Study on the Influence of Inlet Pressure on the Flow Parameters at the Reverse Flow Boundary of Vortex Tube and Its Relation with Energy Separation Performance

Modification and experimental research on vortex tube

Research on the prediction model of energy separation effect of vortex tube based on trajectory deflection characteristics and its numerical solution method

Numerical and Experimental Investigations of Micro Thermal Performance in a Tube with Delta Winglet Pairs

Numerical three-dimensional analysis of the mechanism of flow and heat transfer in a vortex tube

Numerical Simulation for Effects of Venturi Tube on Swirling Flow Field

The thermal performance of a novel convergent valveless vortex tube

Experimental investigation of the flow characteristics within a vortex tube with different configurations

Numerical study on the performance of swirl tube based on orthogonal design

Experimental, computational and optimization studies of temperature separation and flow physics of vortex tube: A review

Computational study of energy separation in convergent-divergent vortex tube for different throat diameters, throat locations, inlet pressures, and working gas

Study on Applicability of Numerical Simulation to Evaluation of Gas Entrainment Due to Free Surface Vortex

Numerical analysis of energy separation in Ranque-Hilsch vortex tube with gaseous hydrogen using real gas model

A numerical study on the flow over a novel tube for heat-transfer enhancement with a linear Eddy-viscosity model

Experimental and Numerical Investigation of a Novel Vortex Reducer in a Co-Rotating Cavity of Aeroengines