Experimental Analysis of the Dynamic North-Finding Method Based on a Fiber Optic Gyroscope: Erratum

Zhen Zhu,Zhongwei Tan,Xinyue Wang,Ziyu Wang

DOI: https://doi.org/10.1364/ao.57.008594

IF: 1.9

2018-01-01

Applied Optics

Abstract:The correction to the funding in Appl. Opt.56, 6504 (2017)APOPAI0003-693510.1364/AO.56.006504 is presented in this erratum.

What problem does this paper attempt to address?

Analysis of Fiber Optic Gyroscope Dynamic Error Based on CEEMDAN

Shuai Zhao,Yilan Zhou,Xiaowu Shu

DOI: https://doi.org/10.1016/j.yofte.2022.102835

IF: 2.8

2022-01-01

Optical Fiber Technology

Abstract:The fiber optic gyroscope (FOG) is an angular rate sensor based on Sagnac effect. It has been widely used in aviation, unmanned, robot, and other fields due to its benefits of all solid state, high precision, and low cost. However, the photoelectric devices inside the FOG will produce a non-negligible error in the dynamic environment, resulting in zero bias drift and increased noise. Currently, research on the dynamic error of FOG focuses primarily on linear vibration, assuming that no input angular rate exists at this moment. However, the dynamic errors caused by angular vibration are more complicated in the practical application environment. The output of FOG includes both effective angular information and dynamic error at this moment, which means that the dynamic error should be removed while the effective angular information must be retained. In this paper, we focus on the effect of angular vibration on FOG, and propose a dynamic error compensation method of FOG based on complete ensemble empirical mode decomposition with adaptive noise (CEEMDAN) that properly separates the effective signal and dynamic error. We also consider the amplitude frequency characteristics of FOG under dynamic conditions and utilize the FOG bandwidth test experiment to verify the effectiveness of our method. The experimental results show that the compensated signal can correctly calculate the bandwidth of FOG. It indicates that our method can effectively compensate the dynamic error in angular vibration environment while improving the performance of FOG in dynamic environment.
Theory And Error Compensation Method Based On The Tilt Sensor Adopted In Dynamic Angle Measurement Of The Fiber Optic Gyroscope

Jiapeng Mou,Tengchao Huang,Xiaowu Shu

DOI: https://doi.org/10.1016/j.yofte.2020.102368

IF: 2.8

2020-01-01

Optical Fiber Technology

Abstract:The fiber optic gyroscope (FOG) has been widely used in the field of dynamic angle measurement due to its characteristics of wide dynamic range and high precision. Considering the change of the installation state of the FOG and the inconvenience of the calibration of the scale factor in engineering, an error compensation of the angle measurement using FOG, which is based on the tilt sensor, is proposed in this paper. Firstly, the principle of the angle measurement based on the FOG and the principle of the tilt sensor are introduced and the error compensation model based on tilt sensor is established. Secondly, simulation analysis and error analysis are performed and the compensation scheme is designed. Finally, according to the compensation scheme, the instrument prototype is built and the experiments are carried out. The experimental results show that although the error is not completely eliminated after adopting compensation scheme, the angle measurement deviation of the FOG can be greatly reduced and limited within 5 '' when the tilt state changes within a small range (the output of the tilt sensor is less than 0.3 degrees). It indicates that the compensation scheme is effective and feasible. More importantly, it is easier to realize in engineering in contrast with other compensation methods.
A Temperature Drift Compensation Method Applied to Fiber Optic Gyroscope North-Seeking

Luo Jinhui,Zhou Yilan,Liu Cheng,Shu Xiaowu

DOI: https://doi.org/10.12086/oee.2020.190681

2020-01-01

Abstract:The startup error of fiber optic gyroscope (FOG) in north-seeking is the error caused by the zero-bias drift of FOG caused by drastic change of the temperature in the starting process. The start-up error significantly increases north-seeking error during the cold startup phase compared to the stable phase, which prolongs the effective north-seeking time. Through the analysis of the factors affecting the temperature drift of FOG, the mul-ti-parameter linear model was established by empirical mode decomposition (EMD), autoregressive-moving average (ARMA) modeling and Kalman filtering to realize a temperature drift compensation method applied to FOG north-seeking. The experimental results show that the method can reduce the north-seeking startup error by nearly 80%, so that the startup north-seeking precision is equivalent to the stable phase and the effective north-seeking time is shortened.
Uncertainty Analysis of Dynamic Goniometer Based on Fiber Optic Gyroscope

Jiapeng Mou,Bin Pang,Guangyao Ying,Fanyan Xue,Tengchao Huang,Shuangliang Che,Xiaowu Shu

DOI: https://doi.org/10.1117/12.2509290

2019-01-01

Abstract:The basic principle of a dynamic goniometer based on fiber optic gyroscope was introduced. According to this principle, the model on uncertainty of angle measurement results was established and the simulation analysis on uncertainty of measurement results was performed. Furthermore, a series of repetitive experiments with this goniometer at different rotational velocities were carried out. Experiments results showed that they were consistent with the uncertainty got from the theoretical analysis when the confidence level was set to 95% and the evaluation model on uncertainty was effective.
Theory and Compensation Method of Axial Magnetic Error Induced by Axial Magnetic Field in A Polarization-Maintaining Fiber Optic Gyro

Yanru Zhou,Yuxiang Zhao,Hui Tian,Dengwei Zhang,Tengchao Huang,Lijun Miao,Xiaowu Shu,Shuangliang Che,Cheng Liu

DOI: https://doi.org/10.1117/1.oe.55.12.126106

IF: 1.3

2016-01-01

Optical Engineering

Abstract:In an axial magnetic field (AMF), which is vertical to the plane of the fiber coil, a polarization-maintaining fiber optic gyro (PM-FOG) appears as an axial magnetic error. This error is linearly related to the intensity of an AMF, the radius of the fiber coil, and the light wavelength, and also influenced by the distribution of fiber twist. When a PM-FOG is manufactured completely, this error only appears a linear correlation with the AMF. A real-time compensation model is established to eliminate the error, and the experimental results show that the axial magnetic error of the PM-FOG is decreased from 5.83 to 0.09 deg/h in 12G AMF with 18-dB suppression. (C) 2016 Society of Photo-Optical Instrumentation Engineers (SPIE)
A New Method to Eliminate the Misalignment Angle in Dynamic Goniometer Based on Fiber Optic Gyro

Jiapeng Mou,Bin Pang,Tengchao Huang,Guangyao Ying,Xiaowu Shu

DOI: https://doi.org/10.1016/j.ijleo.2019.162998

IF: 3.1

2019-01-01

Optik

Abstract:A new development in the dynamic angle measurement based on fiber optic gyro is described, in which a tilt sensor using for accurate measurement of the inclination angle is added to the dynamic goniometer, aiming to eliminating the misalignment angle and improving precision. The principle of the method to eliminate the misalignment angle is introduced in detail. A series of experiments have been carried out to verify this method. Experimental results show the measurement error of the goniometer is better than 2″ and the standard deviation is nearly 0.2″ by this method. It indicates that the method is effective for reducing the misalignment angle and improving the precision of the dynamic goniometer.
A New Optical Method for Suppressing Radial Magnetic Error in a Depolarized Interference Fiber Optic Gyroscope.

Yanru Zhou,Yuxiang Zhao,Dengwei Zhang,Xiaowu Shu,Shuangliang Che

DOI: https://doi.org/10.1038/s41598-018-20487-x

IF: 4.6

2018-01-01

Scientific Reports

Abstract:Based on the theory of the radial magnetic error (RME) in depolarized interference fiber optic gyroscopes (D-IFOGs) under magnetic field, a new optical method is proposed to decrease the RME by adding a suppressing section fiber (SSF) in D-IFOGs. A related theoretical model is established, and the solutions of the parameters of the SSF are obtained with numerical calculations. Then the results of the suppressed RME are simulated. An experimental system is set up to verify the theory and simulation, and the experimental results prove that the RME can be suppressed effectively with a SSF added in the D-IFOG. The magnitude of the RME can be reduced to one-tenth of the original.
Nonreciprocal Phase Error Caused by Orthogonal Magnetic Field in a Polarization-Maintaining Fiber-Optic Gyro

yuxiang zhao,yanru zhou,dengwei zhang,jianhua yang,shenlei shi,xiaowu shu,cheng liu

DOI: https://doi.org/10.1109/JSEN.2015.2435025

2015-01-01

Abstract:This paper aims to investigate the nonreciprocity caused by orthogonal magnetic field (OMF) vertical to the light direction propagating in a polarization-maintaining fiber-optic gyro (PM-FOG). In orthogonal magnetic field, the nonreciprocal phase error (NPE) results from the small change of the propagation constants of the two opposite light waves propagating in the fiber coil. Even using a PM fiber coil, the pressure, twist and other imperfections will change the polarization state, which may lead to an instable drift in PM-FOGs. This phenomenon was observed in the 0°-coupling regime which is commonly used for PM-FOG systems. Theoretical analysis and experimental results show and confirm that the instability of the NPE can be evidently reduced by taking a double-45°-coupling scheme. In this case, the NPE appears to be linear to the OMF and can therefore be compensated via later processes.
Error Analyses for the Algorithms of the Static Fiber-optic Gyro North-finder Schemes

Zhen-hua MAO,Wen-qing ZHOU,Jian-shuang LI,Ting CHEN,Teng-chao HUANG,Yi-lan ZHOU

DOI: https://doi.org/10.3969/j.issn.1000-1158.2011.04.04

2011-01-01

Abstract:Based on the principle of static north finder scheme, error models of several north-finding algorithms were established, and the equations were accordingly deduced to calculate the error with the affection of every parameter in every north-finding algorithm. The result of verifying analysis shows that the four-position north-finding algorithm is less affected by the parameters, such as the latitude of the testing point, and has the higher precision and stability.
Modified Dynamic North-Finding Scheme With a Fiber Optic Gyroscope

Zhu Zhou,Zhongwei Tan,Xinyue Wang,Ziyu Wang

DOI: https://doi.org/10.1109/JPHOT.2018.2817645

IF: 2.4

2018-01-01

IEEE Photonics Journal

Abstract:With the development of laser and optical fiber, the north finding system (NFS) with fiber optic gyroscopes (FOGs) has become an active trend in inertial technology research. This paper demonstrates the error analysis of dynamic north-finding with a fiber optic gyroscope and a new way for the FOGs noise measurement in the dynamic implementation. Moreover, in order to suppress the north-finding err...
Experimental Analysis of the Dynamic North-Finding Method Based on a Fiber Optic Gyroscope

Zhu Zhou,Zhongwei Tan,Xinyue Wang,Ziyu Wang

DOI: https://doi.org/10.1364/ao.56.006504

IF: 1.9

2017-01-01

Applied Optics

Abstract:This paper demonstrates the principles of static and dynamic north-finding methods by measuring the projection of the Earth’s rotation rate with a fiber optic gyroscope. For a comprehensive comparison of the two methods, the influence of a closed-loop feedback mechanism of a servo motor in a turntable is taken into consideration. Thus, we proposed the static and dynamic north-finding experimental implementations according to the different impact of the motor jitters and the different seeking times. Experimental results show that the dynamic method can reduce the north-finding bias error and instability by 60.1% and 54.6%, respectively, in the seeking time of 360 s, while the reduced proportions are 81.3% and 82.5%, respectively, in the seeking time of 120 s, compared with the static method under the jittering effect of the turntable. Therefore, it can be concluded that the dynamic method is more accurate and robust to the jittering effect.
Enhancement of Nonreciprocal Phase Shift by Using Nanoscale Air Gap: Erratum

Ruiyi Chen,Guannan Jiang,Yinlei Hao,Jianyi Yang,Minghua Wang,Xiaoqing Jiang

DOI: https://doi.org/10.1364/ol.38.003354

2013-01-01

Abstract:We correct the calculation method [Opt. Lett.35, 1335 (2010)] of enhancement of nonreciprocal phase shift on the magneto-optical material boundary.
Enhanced optical precursors by Doppler effect via active Raman gain process: erratum

yandong peng,yueping niu,lida zhang,aihong yang,lin jiang,shangqing gong

DOI: https://doi.org/10.1364/OL.38.001388

IF: 3.6

2013-01-01

Optics Letters

Abstract:The affiliation of the third author in an earlier paper [Opt. Lett. 37, 3333 (2012)] was incorrect and is clarified here. In addition, a grant number, omitted from the original paper, is included here. (C) 2013 Optical Society of America
A Segmented Cross-Correlation Algorithm for Dynamic North Finding Using Fiber Optic Gyroscopes

Shuwei Fang,Shanjun Mao,Yanjun Chen,Lanxin Zhu

DOI: https://doi.org/10.3390/s24020322

IF: 3.9

2024-01-06

Sensors

Abstract:Fiber optic gyroscope (FOG)-based north finding is extensively applied in navigation, positioning, and various fields. In dynamic north finding, an accelerated turntable speed shortens the time required for north finding, resulting in a rapid north-finding response. However, with an increase in turntable speed, the turntable's jitter contributes to signal contamination in the FOG, leading to a deterioration in north-finding accuracy. This paper introduces a divide-and-conquer algorithm, the segmented cross-correlation algorithm, designed to mitigate the impact of turntable speed jitter. A model for north-finding error is established and analyzed, incorporating FOG's self-noise and the turntable's speed jitter. To validate the feasibility of our method, we implemented the algorithm on a FOG. The simulation and experimental results exhibited a strong concordance, affirming the validity of our proposed north-finding error model. The experimental findings indicate that, at a turntable speed of 180°/s, the north-finding bias error within a 360 s duration is 0.052°, representing a 64% improvement over the traditional algorithm. These results indicate the effectiveness of the proposed algorithm in mitigating the impact of unstable turntable speeds, offering a solution for north finding with both prompt response and enhanced accuracy.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Enhanced multiposition method to suppress the north finding error caused by bias drift with fiber optic gyroscopes.

Changhong He,Chuanchuan Yang,Xinyue Wang,Ziyu Wang

DOI: https://doi.org/10.1364/AO.52.005303

IF: 1.9

2013-01-01

Applied Optics

Abstract:We present an enhanced multiposition method (EMM) to suppress the north finding error caused by bias drift with fiber optic gyroscopes (FOGs). The new proposal is a static method to find the true north, and it employs a differential strategy and a rotation scheme of increasing step angle. Using the noise model of Allan variance, we analyze the north finding errors caused by angle random walk (ARW), rate random walk (RRW), and rate ramp (RR) theoretically, where RRW and RR are two main noise sources of bias drift, and ARW is the rate white noise. Theoretical analysis indicates that, in the traditional multiposition method (TMM), as the position number increases, the error caused by ARW decreases while that by bias drift increases. Therefore, the suppressions of ARW and bias drift are conflicted with each other. The north finding accuracy is limited by bias drift. In contrast, in EMM, both errors caused by ARW and bias drift will decrease as the position number increases. Experimental results with two specific FOGs verify our theoretical analysis. In our experiments, we study the effect of position number and step angle on the north finding accuracy. Utilizing the proposed EMM, for FOG-1, the north finding error has been reduced by 76.60%, and for FOG-2, a 36.33% reduction has been achieved. Our proposal provides a more effective and stable way to find true north, and it can also be applied to other rate gyroscopes. (c) 2013 Optical Society of America
Method to Suppress Bias Drift and Improve the Accuracy of North Finding with Fiber Optic Gyroscopes

Changhong He,Chuanchuan Yang,Ziyu Wang

DOI: https://doi.org/10.1364/acpc.2012.af4b.8

2012-01-01

Scientia Forestalis

Abstract:This paper presents a new (N + 1)-position method based on a difference scheme and an optimized measurement order of all the positions to effectively improve the accuracy of north finding with fiber optic gyroscopes.
Correction To: GP-SLAM: Laser-Based SLAM Approach Based on Regionalized Gaussian Process Map Reconstruction

Li Bo,Wang Yingqiang,Zhang Yu,Zhao Wenjie,Ruan Jianyuan,Li Ping

DOI: https://doi.org/10.1007/s10514-020-09909-w

IF: 3.255

2020-01-01

Autonomous Robots

Abstract:Unfortunately, the acknowledgement text was incorrectly published in the original article.
Author Correction: Ultra-thin high-efficiency mid-infraredtransmissive Huygens meta-optics

Li Zhang,Jun Ding,Hanyu Zheng,Sensong An,Hongtao Lin,Bowen Zheng,Qingyang Du,Gufan Yin,Jerome Michon,Yifei Zhang,Zhuoran Fang,Mikhail Y. Shalaginov,Longjiang Deng,Tian Gu,Hualiang Zhang,Juejun Hu

DOI: https://doi.org/10.1038/s41467-018-04890-6

IF: 16.6

2018-01-01

Nature Communications

Abstract:The original version of this Article omitted the following from the Acknowledgements:‘J.D. and H. Zhang acknowledge initial funding for design of the meta-atoms provided by the National Science Foundation under award CMMI-1266251. Z.L. and H. Zheng contributed to the Device Fabrication section and were independently funded as visiting scholars by the National Natural Science Foundation of China under award 51772042 and the “111” project (No. B13042) led by Professor Huaiwu Zhang. Later work contained within the Device Modeling and Device Characterization sections and some revisions to the manuscript were funded under Defense Advanced Research Projects Agency Defense Sciences Office (DSO) Program: EXTREME Optics and Imaging (EXTREME) under Agreement No. HR00111720029. The authors also acknowledge fabrication facility support by the Harvard University Center for Nanoscale Systems funded by the National Science Foundation under award 0335765. The views, opinions and/or findings expressed are those of the authors and should not be interpreted as representing the official views or policies of the Department of Defense or the U.S. Government.’ This has been corrected in both the PDF and HTML versions of the Article.
Polarization-Sensitive Perfect Absorbers At Near-Infrared Wavelengths: Erratum (Vol 21, Pg A111, 2013)

Lijun Meng,Ding Zhao,Qiang Li,Min Qiu

DOI: https://doi.org/10.1364/OE.21.00A229

IF: 3.8

2013-01-01

Optics Express

Abstract:In the earlier paper [Opt. Express. 21, A111 (2013)], Fig. 6, Fig. 10, and Fig. 13 were improperly given. They are updated here, and the modifications do not significantly change the paper's findings. (c) 2013 Optical Society of America
Erratum to “general Solution for High Dynamic Range Three-Dimensional Shape Measurement Using Fringe Projection Techniques [opt Lasers Eng 59 (2014) 56–71]”

Shijie Feng,Yuzhen Zhang,Qian Chen,Chao Zuo,Rubin Li,Guochen Shen

DOI: https://doi.org/10.1016/j.optlaseng.2014.04.004

IF: 5.666

2014-01-01

Optics and Lasers in Engineering

Abstract:Erratum to “General solution for high dynamic range three-dimensional shape measurement using fringe projection techniques [Opt Lasers Eng 59 (2014) 56–71]” Shijie Feng , Yuzhen Zhang n, Qian Chen , Chao Zuo , Rubin Li , Guochen Shen a a Jiangsu Key Laboratory of Spectral Imaging & Intelligence Sense, Nanjing University of Science and Technology, Nanjing, Jiangsu Province 210094, China b Key Laboratory of Photoelectronic Imaging Technology and System, Ministry of Education of China. Beijing Institute of Technology, Beijing 100081, China

Experimental Analysis of the Dynamic North-Finding Method Based on a Fiber Optic Gyroscope: Erratum

Analysis of Fiber Optic Gyroscope Dynamic Error Based on CEEMDAN

Theory And Error Compensation Method Based On The Tilt Sensor Adopted In Dynamic Angle Measurement Of The Fiber Optic Gyroscope

A Temperature Drift Compensation Method Applied to Fiber Optic Gyroscope North-Seeking

Uncertainty Analysis of Dynamic Goniometer Based on Fiber Optic Gyroscope

Theory and Compensation Method of Axial Magnetic Error Induced by Axial Magnetic Field in A Polarization-Maintaining Fiber Optic Gyro

A New Method to Eliminate the Misalignment Angle in Dynamic Goniometer Based on Fiber Optic Gyro

A New Optical Method for Suppressing Radial Magnetic Error in a Depolarized Interference Fiber Optic Gyroscope.

Nonreciprocal Phase Error Caused by Orthogonal Magnetic Field in a Polarization-Maintaining Fiber-Optic Gyro

Error Analyses for the Algorithms of the Static Fiber-optic Gyro North-finder Schemes

Modified Dynamic North-Finding Scheme With a Fiber Optic Gyroscope

Experimental Analysis of the Dynamic North-Finding Method Based on a Fiber Optic Gyroscope

Enhancement of Nonreciprocal Phase Shift by Using Nanoscale Air Gap: Erratum

Enhanced optical precursors by Doppler effect via active Raman gain process: erratum

A Segmented Cross-Correlation Algorithm for Dynamic North Finding Using Fiber Optic Gyroscopes

Enhanced multiposition method to suppress the north finding error caused by bias drift with fiber optic gyroscopes.

Method to Suppress Bias Drift and Improve the Accuracy of North Finding with Fiber Optic Gyroscopes

Correction To: GP-SLAM: Laser-Based SLAM Approach Based on Regionalized Gaussian Process Map Reconstruction

Author Correction: Ultra-thin high-efficiency mid-infraredtransmissive Huygens meta-optics

Polarization-Sensitive Perfect Absorbers At Near-Infrared Wavelengths: Erratum (Vol 21, Pg A111, 2013)

Erratum to “general Solution for High Dynamic Range Three-Dimensional Shape Measurement Using Fringe Projection Techniques [opt Lasers Eng 59 (2014) 56–71]”