Abstract:A high sensitivity liquid refractive index (RI) sensor based on a single mode fiber-multimode fiber-tapered thin-core fiber-single mode fiber (SMTTS) structure is simulated by the beam propagation method (BPM). The modal interference between core and cladding mode happened because of modal mismatch and the transmission spectrum is calculated by BPM. The approximate linear relationship between liquid RI and spectrum dip wavelength shifts is obtained to demodulate RI value. To make a comparison, transmissions of single mode fiber-thin-core fiber-single mode fiber (STS) as well as single mode fiber-multimode fiber-thin-core fiber-single mode fiber (SMTS) are also calculated. It is significantly shown that the interference is improved by the segment of multimode fiber (M_MF). And the tapered thin-core fiber (TCF) has the functions that not only further can enhance the fringe visibility, but also can increase the RI sensitivity, which is higher with the thinner thin-core taper diameter. When the taper diameter is 53.51m, the average RI sensitivity could reach up to -116.7nm/RIU within the RI range of 1.33 to 1.39. This is much higher than the value of SMTS structure. And in the practice application, it could be a slimmer taper in the SMTTS structure to improve the sensitivity just achieving by a simple fabrication process. All process could be finished using fusion splicer, cutter and hydrogen flame.

Trench-embedding Fiber Taper Sensor Fabricated by a Femtosecond Laser for Gas Refractive Index Sensing

Multiplexed fiber-optic Fabry-Pérot cavities for refractive index and temperature sensing fabricated using diamond-blade dicing

Novel Intensity-demodulated Fiber-optic Refractive Index Sensor Based on Splicing Point Tapered Fiber

An Open-Cavity Fiber Fabry-Perot Interferometer Fabricated by Femtosecond Laser Micromachining for Refractive Index Sensing

An Interferometric Dual Microfiber Refractive Index Sensor via Tapering of Femtosecond Laser Perforated Optical Fiber

Temperature-insensitive Refractive Index Sensor Based on an Optical Fiber Extrinsic Fabry–Perot Interferometer Processed by a Femtosecond Laser

Fiber Inline Interferometric Refractive Index Sensors Fabricated by Femtosecond Laser and Fusion Splicing

Refractive Index Sensor Based on a Microhole in Single-Mode Fiber Created by the Use of Femtosecond Laser Micromachining

Highly Sensitive Refractive Index Optical Fiber Sensors Fabricated by a Femtosecond Laser

Femtosecond laser fabricated all-optical fiber sensors with ultrahigh refractive index sensitivity: modeling and experiment

In-fiber Mach–Zehnder Interferometer Formed by Large Lateral Offset Fusion Splicing for Gases Refractive Index Measurement with High Sensitivity

All-Fiber Fabry-Perot Interferometer Gas Refractive Index Sensor Based on Hole-Assisted One-Core Fiber and Vernier Effect

Highly Sensitive Gas Refractometers Based on Optical Microfiber Modal Interferometers Operating at Dispersion Turning Point.

High Sensitivity Refractive Index Sensor Based On Tapered Thin-Core Fiber

In-Line Fiber Fabry-Perot Refractive-Index Tip Sensor Based on Endlessly Photonic Crystal Fiber

High Sensitivity Gas Refractometer Based on All-Fiber Open-Cavity Fabry–Perot Interferometer Formed by Large Lateral Offset Splicing

High Sensitivity Refractive Index Sensor based on a Tapered Single-mode-Multimode-Single-mode Fiber Structure

High Sensitivity Refractometer Based on Tapering Two-Mode Fiber Embedded Long-Period Fiber Grating

Low-Temperature Cross-Sensitivity Refractive Index Sensor Based on Single-Mode Fiber with Periodically Modulated Taper

Femtosecond Laser Fabricated In-Line Micro Multicavity Fiber FP Interferometers Sensor

A Miniature Fiber-Optic Refractive-Index Sensor Based on Laser-Machined Fabry-Perot Interferometer Tip