Abstract:In this paper, a novel droplet + arc additive manufacturing (DAAM) has been proposed for building aluminum alloy components with high quality and high efficiency. A special droplet generation system (DGS) was designed to replace the traditional wire feeding system, making the material addition process and the arc heat input process two independent parts. During the DAAM process, the arc heat source with variable polarity is arranged tilted below the DGS, the droplets which generated from DGS drop vertically and sequentially into the molten pool, and the aluminum alloy component can be deposited layer-by-layer by moving substrate. The droplet generation process, droplet + arc deposition process, as well as the heat input strategy, microstructure and mechanical properties of the thin-wall component are discussed in detail. The experimental results show that the small and sequential droplet generation mode is beneficial to improve the continuity of deposition process and significantly reduce the harmful impact of droplets on the molten pool. Meanwhile, the DAAM process shows great inclusiveness of droplet falling deviation. A multi-layer thin-wall component and a ring-shaped structure were fabricated successfully by DAAM with the deposition rate of 140 mm3/s. The microstructure of the thin -wall component is dominated by columnar crystals and it has obvious periodic distribution along the deposi-tion direction. The tilted growth of columnar crystals results in different grain morphology in the cross section and longitudinal section. After T6 heat treatment, the average ultimate tensile strength (UTS) and elongation in the horizontal direction are 435.0 MPa and 10.4%, while the average UTS and elongation in the vertical direction are 406.5 MPa and 16.4%, respectively. The fracture morphology is dominated by ductile fracture, but it exhibits some intergranular fracture characteristic in the horizontal direction. This novel DAAM provides a new choice for additive manufacturing of aluminum alloy, and shows great potential for the simultaneous improvement of the manufacturing quality and efficiency.

A Novel Ultrasonic Rolling Assisted Direct Energy Deposition Method with Semi-Solid Thixo-Forming Characteristics for Aa6061

Wire-Arc Directed Energy Deposition of Aluminum Alloy 7075 with Dispersed Nanoparticles

Effects of plastic deformation of solid phase on mechanical properties and microstructure of wrought 5A06 aluminum alloy in directly semisolid thixoforging

Directed energy deposition of Al-Mg-Si alloys with fully-equiaxed microstructure and isotropic high strength/ductility

Microstructure and Mechanical Properties of Thixoforming 6066Al by Spray Deposition

Microstructure evolution and tensile mechanical properties of thixoformed high performance Al-Zn-Mg-Cu alloy

Isotropic and improved tensile properties of Ti-6Al-4V achieved by in-situ rolling in direct energy deposition

Thixotropic Deformation Behavior, Rapid Spheroidization and Solid-Liquid Homogenization of Semi-Solid Al0.8Co0.5Cr1.5CuFeNi HEA with Multilevel Microstructure

Thermomechanical processing of AA6061 billets for semi-solid forming

Integrated Manufacturing of Powder Metallurgy Preparation-Thixoforming for Al0.8Co0.5Cr1.5CuFeNi HEA: Excellent Formability and Enhancement by In-Situ Generated Al2O3 in Liquid Phase

A Novel Droplet + Arc Additive Manufacturing for Aluminum Alloy: Method, Microstructure and Mechanical Properties

Microstructural Evolution of Semisolid 6063 Aluminum Alloy Prepared by Recrystallization and Partial Melting Process

Solid-state Additive Manufacturing High Performance Aluminum Alloy 6061 Enabled by an In-Situ Micro-Forging Assisted Cold Spray

Improving mechanical properties of wire arc additively manufactured AA2196 Al–Li alloy by controlling solidification defects

Thixoforming-forging compound forming technology for 6A02 Al bracket-shape component

Effect of Rotational Shear and Heat Input on the Microstructure and Mechanical Properties of Large-Diameter 6061 Aluminium Alloy Additive Friction Stir Deposition

Enhanced Plastic Stability: Achieving High Performance in a Al6xxx Alloy Fabricated by Additive Manufacturing

Microstructural modification and enhanced mechanical properties of wire-arc additive manufactured 6061 aluminum alloy via interlayer friction stir processing

Coaxial Laser Metal Wire Deposition of Ti6Al4V Alloy: Process, Microstructure and Mechanical Properties

Achieving high strength-ductility of Al-Zn-Mg-Cu alloys via hot-wire arc additive manufacturing enabled by strengthening precipitates

Deciphering the Microstructural Development and Excellent Ductility in Electron Beam Wire-Fed Additive Manufacturing of Ti-6Al-3Nb-2Zr-1Mo Alloys Based on High Deposition Rate