Abstract:Due to their extremely high energy demand, data centers are directly supplied from a medium-voltage (MV) grid. However, a significant part of this energy is dissipated in the power supply chain since the MV is reduced step-by-step through multiple power conversion stages down to the chip-voltage level. In order to increase the efficiency of the power supply chain, the number of conversion stages must be substantially reduced. In this context, solid-state transformers (SSTs) are considered as a possible solution, as they could directly interface the MV AC grid to a 400 V DC bus, whereby server racks with a power consumption of several tens of kilowatts could be directly supplied from an individual SST. With a focus on the lowest system complexity, the SST, ideally, should be built as simple two-stage system consisting of an MV AC/DC power factor correction (PFC) rectifier stage followed by an isolated DC/DC converter. Accordingly, this paper focuses on the design and realization of a 25 kW, 3.8 kV single-phase AC to 7 kV DC PFC rectifier unit based on the 10 kV SiC MOSFETs. By simply adding an $LC$ circuit between the switch nodes of the well-known full-bridge-based pulse width modulated AC/DC rectifier, the integrated triangular current-mode concept is implemented, which only internally superimposes a large triangular current ripple on the AC mains current and, therefore, enables zero-voltage switching over the entire AC mains period. Special attention is paid to the realization of the MV inductors and their electrical insulation, the AC-input $LCL$ filter to limit electromagnetic interference emissions, and the challenges arising due to cable resonances when connecting the SST to the MV grid via an MV cable. Despite the large insulation distances required for MV, the realized 25 kW MV PFC rectifier achieves an unprecedented power density of 3.28 kW/L (54 W/ $\mathrm {in}^{3}$ ) and a full-load efficiency of 99.1%, determined using a calorimetric measurement setup, which is discussed in detail in the Appendix.

7.2Kv/100kva Solid State Transformer Based on Half Bridge LLC Resonant Converter and 15kv SiC AC Switch

A Soft-Switching Solid-State Transformer Module

Design and experiment of a zero-voltage-switching module for bidirectional DC solid-state transformer

A Five-level AC/DC Converter for MV Solid-State Transformer

A Soft-switching Universal-input Solid State Transformer

Design and Implementation of a 7.2kv Single Stage AC-AC Solid State Transformer Based on Current Source Series Resonant Converter and 15 Kv SiC MOSFET

7.2-kV Single-Stage Solid-State Transformer Based on the Current-Fed Series Resonant Converter and 15-kV SiC mosfet s

13.8kV/400kW Solid State Transformer DC Fast Charger (SST-DCFC) Based on 15kV SiC AC Switch

Medium Voltage Solid State Transformers Based on 15 Kv SiC MOSFET and JBS Diode.

Design of A Medium Voltage Solid-State Transformer Based on Modular AC-AC Resonant Converter and an Input-Series-Output-Parallel Architecture

15-Kv/50-a SiC AC Switch Based on Series Connection of 1.7-Kv MOSFETs

Design And Demonstration Of A Sic-Based 800-V/10-Kv 1-Mw Solid-State Transformer For Grid-Connected Photovoltaic Systems

270 Kva Solid State Transformer Based on 10 Kv SiC Power Devices

500Kva Hybrid Solid State Transformer (HSST): Design and Implementation of the SST

Design and Analysis of a 270kW Five-level DC/DC Converter for Solid State Transformer Using 10kV SiC Power Devices

15 Kv SiC MOSFET: an Enabling Technology for Medium Voltage Solid State Transformers

99.1% Efficient 10 kV SiC-Based Medium-Voltage ZVS Bidirectional Single-Phase PFC AC/DC Stage

Improved medium voltage AC-DC rectifier based on 10kV SiC MOSFET for Solid State Transformer (SST) application

Medium Voltage Soft-Switching DC/DC Converter with Series-Connected SiC MOSFETs

Design of AC High-Voltage Switch for Solid-State Transformer of Smart Grid