Abstract:Recently, the utilization of lithium has increased significantly, particularly in high-tech industries such as nuclear, aerospace, automotive, battery, military, glass and ceramic, and lubricants. However, lithium recovery methods from brines present certain drawbacks, making lithium exploitation a global challenge. A comparative analysis of lithium recovery methods from brine solutions indicates that the adsorption method holds promising potential for separating lithium from low-concentration solutions. Despite this, the quest for an effective and efficient adsorbent for lithium-ion adsorption remains a challenge, necessitating the development of an adsorbent, using readily available materials. In this study, carbon-active underwent chemical modification. Notably, the co-precipitation method was employed for the first time to create a composite adsorbent decorated with manganese dioxide (MnO 2 ). Various analyses, including XRD, SEM-EDS, FTIR, and BET, were conducted to elucidate the structural, morphological, physical, and chemical properties of the adsorbent. This synthesized adsorbent was applied to the adsorption of lithium from an aqueous sample. Exploration of adsorption parameters affecting capacity led to the identification of optimal conditions: 14-hour duration, an adsorbent dosage of 0.02 g, and an ambient temperature of 25°C, in a lithium solution with a concentration of 60.4 ppm. Under these conditions, the maximum adsorption capacity of the adsorbent was determined to be 30.5 mg/g. Based on experimental results, kinetic and adsorption isotherm models were investigated. The Pseudo-quadratic kinetic model, with an R 2 value of 0.999, emerged as the most suitable for describing the adsorbent's behavior. The Hill isotherm model with R2 = 0.9634 is the most appropriate isotherm model to describe the adsorbent behavior. Additionally, the selectivity of the adsorbent in the presence of other ions was investigated. The adsorbent's reusability was examined, and after two recycling periods, the adsorbent maintained an efficiency of up to 88%, demonstrating its stability. The CAC-MnO2-P composite adsorbent shows technical and economic promise for industrial use in lithium-ion recovery processes.

Adsorption of Li+ by Imprinted Capacitor Deionization — A New Method for Selective Recovery of Valuable Lithium in Acidic Solutions

Nitrogen-doped substrate material ion imprinting–capacitive deionization selective recovery of lithium ions from acidic solutions

A lithium ion-imprinted adsorbent using magnetic carbon nanospheres as a support for the selective recovery of lithium ions

Extraction of lithium ions from acidic solution using electrochemically imprinted membrane

Thermo-responsive ion imprinted polymer on the surface of magnetic carbon nanospheres for recognizing and capturing low-concentration lithium ion

Capacitive lithium capture system using a mixed LiMn2O4 and LiAlO2 material

Selective Lithium separation from Li/Co/Ni mixtures using optimized flow-electrode capacitive deionization

Electrospun nanofiber membrane of dibenzo 14-crown-4-ether polyimide for efficient selective lithium recovery from discarded lithium-ion batteries

Development of a Manganese Dioxide-Decorated Activated Carbon Nano-sorbent via Co-precipitation method for efficient lithium ion adsorption from aqueous solutions

Recovery of Lithium Ions From Salt Lakes Using Nanofibers Containing Zeolite Carriers

Bipolar membrane capacitive deionization for the selective capture of lithium ions from brines and conversion to lithium hydroxide

Highly efficient and selective extraction of Li+ from high sodium lithium containing wastewater using manganese series adsorbent

Facile Synthesis of Degradable CA/CS Imprinted Membrane by Hydrolysis Polymerization for Effective Separation and Recovery of Li+

Preparation of a novel ion-imprinted membrane using sodium periodate-oxidized polydopamine as the interface adhesion layer for the direction separation of Li+ from spent lithium-ion battery leaching solution

Adsorption performance and mechanism of TiO 2 /PVDF-based lithium-ion imprinted membrane in leaching solution of spent lithium-ion batteries

Hard carbon with an “adsorption-intercalation/filling” behavior for selective deionization of lithium ions

Highly Selective Granulation Adsorbents for Lithium Recovery from Gas Field Brine: Selectivity, Kinetics and Mechanism

Selective lithium extraction from diluted binary solutions using metal-organic frameworks (MOF)-based membrane capacitive deionization (MCDI)

Electrochemical recovery lithium from brine via taming surface wettability of regeneration spent batteries cathode materials

Acid-Free and Selective Extraction of Lithium from Spent Lithium Iron Phosphate Batteries Via a Mechanochemically Induced Isomorphic Substitution