Abstract:The practical engineering applications of powder metallurgy (PM) Ti alloys produced through cold compaction and pressure-less sintering are impeded by poor sintering densification, embrittlement caused by excessive O impurities, and severe sintering deformation resulting from the use of heterogeneous powder mixtures. This review presents a summary of our previous work on addressing the above challenges. Initially, we proposed a novel strategy using reaction-induced liquid phases to enhance sintering densification. Near-complete density (relative density exceeding 99%) was achieved by applying the above strategy and newly developed sintering aids. By focusing on the O-induced embrittlement issue, we determined the onset dissolution temperature of oxide films in the Ti matrix. On the basis of this finding, we established a design criterion for effective O scavengers that require reaction with oxide films before their dissolution. Consequently, a ductile PM Ti alloy was successfully obtained by introducing 0.3wt% NdB 6 as the O scavenger. Lastly, a powder-coating strategy was adopted to address the sintering deformation issue. The ultrafine size and shell-like distribution characteristics of coating particles ensured rapid dissolution and homogeneity in the Ti matrix, thereby facilitating linear shrinkage during sintering. As a result, geometrically complex Ti alloy parts with high dimensional accuracy were fabricated by using the coated powder. Our fundamental findings and related technical achievements enabled the development of an integrated production technology for the high-performance and accurate shaping of low-cost PM Ti alloys. Additionally, the primary engineering applications and progress in the industrialization practice of our developed technology are introduced in this review.

Impurity Scavenging from Powder Metallurgy Titanium Alloys by Rare Earth Elements

Simultaneous gettering of oxygen and chlorine and homogenization of the β phase by rare earth hydride additions to a powder metallurgy Ti-2.25Mo-1.5Fe alloy

Achieving synergy of strength and ductility in powder metallurgy commercially pure titanium by a unique oxygen scavenger

In situ synchrotron radiation to understand the pathways for the scavenging of oxygen in commercially pure Ti and Ti-6Al-4V by yttrium hydride

Impurity (Fe, Cl, and P)-Induced Grain Boundary and Secondary Phases in Commercially Pure Titanium (CP-Ti)

Effect of rare earth elements on plasma electrolytic carbonitriding of Ti–6Al–4V alloy

The Scavenging Effect of Different Rare-Earth Elements in the Low-Purity Zr50Cu40Al10 Alloy

Impacts of Yttrium on Microstructure and Tensile Properties of Biomedical Β Ti-Nb-Zr Fabricated by Metal Injection Molding

Yttrium for the Selective Laser Melting of Ti-45Al-8Nb Intermetallic: Powder Surface Structure, Laser Absorptivity, and Printability

Integrated high-performance and accurate shaping technology of low-cost powder metallurgy titanium alloys: A comprehensive review

Electrosynthesis of Titanium from High-Titanium Slag with Short-Process in Molten CaCl2

Purification of Scandium from Concentrate Generated from Titanium Pigments Production Waste

Study on the Migration Patterns of Oxygen Elements during the Refining Process of Ti-48Al Scrap under Electromagnetic Levitation

Improving mechanical property of Ti55531 alloy by yttrium dopant

Titanium Extraction from Titania-Bearing Blast Furnace Slag: A Review

Influence of Yttrium on Purification and Carbide Precipitation of Superalloy K4169

Selective enrichment and extraction of well-catalyzed perovskites on melting-microwave heating process from blast furnace slag

Effect of Rare Earth Y Addition on the Microstructure and Mechanical Properties of Ti(C,N)-304ss Cermets

Residual titanium flakes as a novel material for retention and recovery of rare earth and relatively rare earth elements

Migration and Enrichment Behaviors of Ca and Mg Elements during Cooling and Crystallization of Boron-Bearing Titanium Slag Melt

Properties of various CaO-Al2O3-TiO2 refractories and their reaction behaviours in contact with Ti6Al4V melts