Reduction of Thermocapillary Convection in a Silicon Liquid Bridge by a Non-Contaminating Method

Jian Li,M-W Li,Zeng Dl

2002-01-01

Abstract:The floating zone technique is a promising containerless method for the growth of high-quality silicon crystal under microgravity. In the absence of buoyancy driven flow, thermocapillary (Marangoni) convection induced by surface tension gradient becomes highlight and plays an important role. Som...

What problem does this paper attempt to address?

Numerical Investigation of the Effect of Rotation on the Oscillatory Thermocapillary Convection and Dopant Transport in a Silicon Liquid Bridge

Chengcheng Le,Lijun Liu,Zaoyang Li

DOI: https://doi.org/10.1016/j.jcrysgro.2019.125149

IF: 1.8

2019-01-01

Journal of Crystal Growth

Abstract:As a crucible-free method, the floating zone method can provide suitable conditions for growing high purity silicon single crystals for semiconductor devices. For doped crystals, the three-dimensional and oscillatory thermocapillary convection during growth always lead to undesirable macro-segregation and dopant striations. Three-dimensional numerical transient simulations are carried out for a laterally heated silicon liquid bridge to study the oscillatory thermocapillary convection and dopant transport. A small temperature variation can induce the periodic oscillatory flow in the liquid bridge which leads to a non-axisymmetric and periodic dopant distribution at the growth interface. Effect of rotation on the oscillatory thermocapillary convection and time-dependent dopant distribution at the growth interface is investigated. Sufficient crystal rotation is helpful to increase azimuthal uniformity and reduce concentration variation at the growth interface. The iso-rotation of crystal and feed is favorable for eliminating the oscillations of thermocapillary convection and concentration. However, for the same rotation rate, the stronger forced convections in the cases of single-rotation of crystal and conter-rotation of crystal and feed are more efficient in reducing concentration variation at the growth interface, and the concentration oscillation can be reduced by increasing rotation rate in both cases.
Stability of buoyancy–thermocapillary convection in molten silicon liquid bridge between two disks with different radii under gravity

Yaming Tu,Zhong Zeng,Liangqi Zhang,Yue Wang,Yong Liu,Hao Li,Chengzhao Liu,Linmao Yin,Hao Liu

DOI: https://doi.org/10.1063/5.0187767

IF: 4.6

2024-02-01

Physics of Fluids

Abstract:By employing a linear stability analysis based on the spectral element method, we investigated the impact of radius ratio (Γr) on the stability of buoyancy–thermocapillary convection in a molten silicon liquid bridge (Pr = 0.011). This liquid bridge was located between two coaxial disks with different radii under the influence of gravity. The aspect ratio of the liquid bridge was maintained at Γ = 1, with a volume ratio Γv = 1 and a fixed height. To explore the physical mechanisms behind convection instability, a perturbation energy analysis was adopted. The free surface shape was determined using the Young–Laplace equation, and two distinct heating strategies were employed. In a top-heated liquid bridge, the convection stability under gravity is always stronger than under zero-gravity. However, in a bottom-heated liquid bridge, the convection stability under gravity is not consistently stronger than under zero-gravity; specifically, when 0.522 < Γr < 0.673, the convection stability under gravity is weaker than under zero-gravity. Despite the small height of the liquid bridge (approximately 2 mm), the maximum relative difference of the critical Marangoni number (Mac) between gravity and zero-gravity conditions reaches as high as 227.8%. In a bottom-heated liquid bridge, oscillatory instability occurs at larger radius ratios (Γr = 0.8) compared to the zero-gravity condition. Furthermore, all instabilities for various radius ratios and heating strategies were found to be of hydrodynamic in nature.

mechanics,physics, fluids & plasmas
Effect of Liquid Encapsulation on Thermocapillary Convection in Molten Liquid under Microgravity Condition

QUAN Xiao-jun,PENG Lan,FENG Cui-hua

DOI: https://doi.org/10.3969/j.issn.1008-8032.2004.01.006

2004-01-01

Abstract:This paper establishes the physical and mathematical model of thermocapillary convection in molten liquid with liquid encapsulation. Numerical simulation of thermocapillary convection in molten liquid with liquid encapsulation is performed by finite volume method. The distributions of temperature and velocity in liquid layers is then obtained.It is verified that liquid encapsulation can reduce thermocapillary convection in molten liquid and raise the quality of crystal growth. The effects of thickness of liquid encapsulation and of kinetic viscosity on thermocapillary convection in molten liquid are analyzed.
Reorientation of Hydrogen Bonds Renders Unusual Enhancement in Thermal Transport of Water in Nanoconfined Environments

Yuan Gao,Ziqiao Chen,Yue Zhang,Yanwei Wen,Xiaotong Yu,Bin Shan,Baoxing Xu,Rong Chen

DOI: https://doi.org/10.1021/acs.nanolett.4c01338

IF: 10.8

2024-01-01

Nano Letters

Abstract:Liquid confined in a nanochannel or nanotube has exhibited a superfast transport phenomenon, providing an ideal heat and mass transfer platform to meet the increasingly stringent challenge of thermal management in developing high-power-density nanoelectronics and nanochips. However, understanding the thermal transport of confined liquid is currently lacking and is speculated to be fundamentally different from that of bulk counterparts due to the unprecedented thermodynamics of liquid in nanoconfined environments. Here, we report that the thermal conductivity of water confined in a silica nanotube is nearly 2-fold as that of bulk status. Further molecular dynamics simulations reveal that this unusual enhancement originates from the densification and reorientation of local hydrogen bonds close to the nanotubes. Thermal-confinement scaling law is established and quantitatively supported by comprehensive simulations with remarkable agreement. Our findings lay a theoretical foundation for designing nanofluidics-enabled cooling strategies and devices.
Effect of a Uniform Axial Magnetic Field on the Spatiotemporal Evolution of Thermocapillary Convection in a High Prandtl Fluid Under Microgravity

Shuo Yang,Pushi Ge,Yu Gao,Jintao Luo,Tianyu Wang,Zhe Liu,Yunyi Zheng,Wanqi Li,Jie Cui

DOI: https://doi.org/10.3390/sym16121645

2024-12-13

Symmetry

Abstract:In this paper, the semi-floating liquid bridge model with the silicone oil-based ferromagnetic fluid under microgravity was taken as the research object. The enhanced level set method was employed to numerically monitor the free surface flow characteristics, utilizing a staggered grid. The internal flow, temperature, velocity and interface deformation of thermocapillary convection under a uniform axial magnetic field were studied by direct numerical simulation. The results show that the transverse development of thermocapillary convection is suppressed by the axial uniform magnetic field, and the cell flow is controlled near the free surface. The average axial velocity was increased by about three times, and the average radial velocity was increased by about two times. The average axial temperature near the free surface was much higher than that on other radii. The axial temperature level of the surface flow was improved under of the influence of a uniform axial magnetic field. The axial temperature gradient in the central area of the liquid bridge basically showed the same change rule. The closer to the hot disk of the liquid bridge, the larger the axial temperature gradient. In addition, the axial uniform magnetic field effectively suppressed the micro-deformation of the free interface, and the free surface micro-deformation was at an order of magnitude of 10−5 (the deformation of the free surface in thermocapillary convection within a liquid bridge without a magnetic field was at an order of magnitude of 10−4). Therefore, studying the influence of the axial magnetic field on the thermocapillary convection of a high Prandtl number fluid can provide the necessary theoretical support for the development of crystal preparation technology.

multidisciplinary sciences
Heat Flow Control and Segregation in Directional Solidification: Development of an Experimental and Theoretical Basis for Bridgman-Type Growth Experiments in a Microgravity Environment

F. A.

Abstract:Within the framework of the proposed research, emphasis was placed on application of magnetic fields to semiconductor growth systems. Through complementary support by the Air Force and DARPA, we were able to acquire a superconducting magnet which can provide axial magnetic fields of up to 30 kGauss for melt stabilization in the NASA facility for heat pipe based vertical BridgmanStockbarger growth. It was found that axial fields up to 3 kGauss do not affect the growth behavior nor the macro-segregation behavior in the system Ge(Ga). Applied fields are found to significantly alter the radial dopant distribution, which is attributed to alterations in the spatial orientation of convective cells. Increasing the applied magnet field to 30 kGauss is found to have a fundamental effect on dopant segregation. The initial transient segregation behavior is identical with that predicted by Tiller e t al. for diffusion controlled plane front solidification. Within the transient region, the dopant concentration increased by in excess of 600%, a concentration increase which in the magnitude has thus far only been observed in the ASTP experiment conducted in the reduced gravity environment of space. While the apparent achievement of diffusion controlled growth, as indicated by theory, is contingent on the validity of the available database, the experimental results demonstrate that magnetic melt stabilization can be valuable in emulating a limited spectrum of reduced gravity conditions. The experiments also point to the need, in space, for extended equilibration of melts prior to solidification, and alternatively, at the need for force convective mixing in a microgravity environment. . Emphasis was also place on the exploration of the potential of KC-135 flights for preliminary studies of the effects of reduced gravity environment on the wetting behavior of semiconductor systems in growth configuration. The experiments indicated different solidification characteristics; however, it was not possible to obtain quantitative data on wetting. The primary problem consisted of deficiencies of the available hardware. The limited number of experiments conducted does not permit any conclusions on the merits of KC-135 flights for semiconductor processing research. It is established, however, that the effective use of this facility will require acquisition of appropriate hard ware. At professional meetings, presentations were made on the potential of reduced gravity environment of R&D in materials processing. -49https://ntrs.nasa.gov/search.jsp?R=19890004306 2019-11-28T09:08:54+00:00Z

Materials Science,Physics,Engineering
Mesoscale Simulation of Marangoni Convection about a Vapor Bubble in a Liquid with Temperature Gradients under Microgravity Conditions

Chaoyang Zhang,Ping Cheng,Jianguang Cao

DOI: https://doi.org/10.1016/j.icheatmasstransfer.2016.09.005

IF: 6.782

2016-01-01

International Communications in Heat and Mass Transfer

Abstract:Marangoni convection around a 2-D vapor bubble in a liquid, subjected to an imposed negative temperature gradient in the vertical direction under microgravity conditions, is simulated with a newly developed lattice Boltzmann liquid/vapor phase-change method. It is shown that a floating bubble, initially at the center of a confined space, moves gradually toward the hot wall under zero gravity condition because of Marangoni convection. With the increase of the Marangoni number, Marangoni convection along the liquid–vapor interface appears to be more and more significant. Under microgravity conditions, a sessile bubble attached on a hot bottom wall facing upward at low superheats, the high velocity region on the liquid/vapor interface moves from the triple-contact line region upward as the wettability of the solid surface changes from hydrophobic to hydrophilic. It is shown that the average Nusselt number of such a sessile vapor bubble under microgravity conditions is larger or smaller than those under zero gravity condition, depending on whether the Marangoni convection is in a direction parallel to or opposite to the direction of the gravity.
Influence of Gravitational Tilt on the Thermocapillary Convection in a Non-Axisymmetric Liquid Bridge

Shuo Yang,Yupeng Zhang,Jie Cui,Daocheng Qin,Yuhang Wang,Pushi Ge,Jintao Luo,Duojiao Guan,Yunyi Zheng

DOI: https://doi.org/10.1088/1367-2630/ad25a7

2024-02-04

New Journal of Physics

Abstract:Fluid slosh caused by residual acceleration in microgravity is a common problem encountered in space engineering. To solve this problem, the ground-based experiment research on the influence of gravity jitter and gravitational tilt on the thermocapillary convection (TCC) transition behavior of non-axisymmetric liquid bridge has become an important issue in microgravity fluid management. Based on a mesoscale liquid bridge experimental platform which can realize gravitational tilt, the effect of gravitational tilt on TCC by using a high-speed camera equipped with a near-focus lens and a self-developed interface image recognition package. The results show that the spatio-temporal evolution of TCC by the influence of gravitational tilt is still divided into steady and oscillatory flow. In the stable TCC, the vortex core distortion of cellular flow caused by the imbalance left and right interface curvature invites cellular flow close to the free surface, and it shrinks to the intermediate height. As gravitational tilt increases, the transverse/longitudinal velocity peaks are significantly reduced, peak velocity has been reduced by 26-27%. Meanwhile, the longitudinal velocity gradient at the free interface increases significantly. Therefore, gravitational tilt plays an important role in improving the surface flow velocity. In the oscillatory TCC, the position of vortex core is closer to the free interface at the hot/cold corner as the periodic mutual occupation of the left and right cellular flows. The TCC is obviously inhibited due to the gravitational tilt. The critical temperature difference is increased by 25% and the onset of temperature oscillation at the hot corner is delayed by 20% compared with conventional gravity condition.

physics, multidisciplinary
Effect of volume ratio on thermocapillary convection in annular liquid pools in space

Jia Wang,Ziyi Guo,Chengjun Jing,Li Duan,Kai Li,Wenrui Hu

DOI: https://doi.org/10.1016/j.ijthermalsci.2022.107707

IF: 4.779

2022-05-27

International Journal of Thermal Sciences

Abstract:In systems with liquid/liquid or liquid/gas interface under microgravity, and even in shallow liquid layers in the terrestrial conditions, thermocapillary force takes the principal role to drive natural convections. A series of numerical simulations are conducted to investigate the stability limit of axisymmetric steady thermocapillary flow in annular liquid pools with curved and adiabatic liquid surface for eight volume ratios 0.809 ≤ Vr ≤ 1.173, where Vr is defined as (liquid vol/vol of the annular gap). Simulations provide the critical temperature difference Δ T c , frequency f c , and azimuthal wave number m c for each liquid pool. At the critical condition, oscillations start in form of standing wave. At the slightly supercritical condition (Δ T *), the standing waves turn to traveling oscillations. The calculated Δ T c values decrease with the increase of Vr . A simulation code with a convective thermal boundary condition in the liquid surface suggests that heat transfer through the liquid surface significantly increases the Δ T c value.

engineering, mechanical,thermodynamics
Experimental study of the effect of noncondensables on buoyancy-thermocapillary convection in a volatile low-viscosity silicone oil

Y. Li,R. Grigoriev,M. Yoda

DOI: https://doi.org/10.1063/1.4904870

IF: 4.6

2014-12-01

Physics of Fluids

Abstract:The convective flow in a layer of volatile silicone oil with a kinematic viscosity of 0.65 cSt confined to a sealed cavity with a transverse aspect ratio of 3.2 was visualized using particle pathlines and quantified by particle-image velocimetry at dynamic Bond numbers estimated to be of order unity and laboratory Marangoni numbers as great as 3600. The effect of noncondensables (i.e., air) was studied by comparing convection in the liquid layer below a vapor space at pressures ranging from 4.8 kPa to 101 kPa, corresponding to air molar fractions ranging from 14% to 96%, respectively, and silicone-oil vapor, under otherwise identical conditions. The results for convection at 101 kPa are in qualitative agreement with previous studies, and clarify the time-dependent flow observed at high Marangoni numbers. The results show that decreasing the relative air concentration increases the critical Marangoni numbers for transition between different flow states, even though the air concentration does not appear to affect the speeds near the interface. Linear stability analysis shows that transitions are suppressed due to the latent heat generated or absorbed at the interface due to the enhancement of phase change. Furthermore, the experimental results suggest that air, even at relative concentrations as small as 14%, or partial pressures of O(102 Pa), has a significant effect on the vapor flow, and that the fluid in the vapor space should be modeled as a binary mixture in many cases of practical interest.

mechanics,physics, fluids & plasmas
Suppression of Melt Convection in a Proposed Bridgman Crystal Growth System

J. A. Wei,L. L. Zheng,H. Zhang

DOI: https://doi.org/10.1016/j.ijheatmasstransfer.2009.02.029

2009-01-01

Abstract:Numerical simulations are performed for Bridgman crystal growth of several semiconductor materials, such as InAs, InSb, GaSe, CdTe, PbTe, and GaP. For materials with low Prandtl and low Grashof numbers, melt convection is weak and the traditional Bridgman technique is a suitable growth process. For the materials with high Prandtl numbers in their melt status and the growth system with high Grashof number, the temperature field and the growth interface are significantly influenced by melt flow, resulting in the complicated flow pattern and curved interface shape. A new Bridgman crystal growth system is proposed to suppress convection and improve solidification interface shape by cooling of the top melt. The results obtained from the proposed design demonstrate that melt convection may be controlled by adjusting the design parameters. Further, parametric studies are performed to determine the influence of the control parameters on melt flow and solidification interface.
Flow instabilities in thermocapillary liquid bridges between two coaxial disks with different radii

Yue Wang,Zhong Zeng,Hao Liu,Liangqi Zhang,Linmao Yin,Yao Xiao,Yong Liu

DOI: https://doi.org/10.1016/j.ijheatmasstransfer.2021.122182

IF: 5.2

2022-02-01

International Journal of Heat and Mass Transfer

Abstract:The primary instability of thermocapillary flow in a liquid bridge between two coaxial disks with different radii is investigated under microgravity for silicon melt with Prandtl number Pr=0.011 via two heating strategies. The static deformation of the free surface is considered by solving the Young-Laplace equation. The physical instability mechanisms are explored by analyzing the energy budgets of the critical modes, which are determined by linear stability analysis based on the Legendre spectral element method. With the decrease of radius ratio Γr , the stability of thermocapillary flow is significantly improved. In contrast to typical cylindrical liquid bridges (Γr =1), the instability is an oscillatory bifurcation for small radius ratios (Γr ≤0.672) when the liquid bridge is heated from the bottom disk. Furthermore, the instabilities for all radius ratios and heating strategies are found to be purely hydrodynamic, but the specific instability mechanisms are different.

engineering, mechanical,thermodynamics,mechanics
Oscillatory Thermocapillary Convection in Deformed Half Zone Liquid Bridges of Low Prandtl Number Fluids

Chengcheng Le,Lijun Liu,Zaoyang Li

DOI: https://doi.org/10.1016/j.icheatmasstransfer.2021.105499

IF: 6.782

2021-01-01

International Communications in Heat and Mass Transfer

Abstract:A series of three-dimensional (3D) transient simulations are carried out to study the onset and features of oscillatory thermocapillary convection in deformed half zone liquid bridges of low Prandtl number fluids (Pr = 0.01) with unit aspect ratio (As). The critical conditions for different volume ratios on ground and under microgravity are determined. It turns out that the threshold of the second bifurcation is more sensitive to volume ratio than the first bifurcation. The thresholds in deformed liquid bridges are usually higher than those in cylindrical liquid bridges. The critical azimuthal wavenumber increases from 2 to 3 with volume ratio. Gravity affects the flow through three factors. Compared with the hydrostatic deformation and heating orientation, buoyancy is marginal to the flow transition. It only affects the threshold and the deviation caused by buoyancy is within 2%. The effects of gravity on the critical conditions are dependent on volume ratio. Except for the threshold, gravity may also affect the critical azimuthal wavenumber and the critical oscillation mode. 3D oscillatory flow regimes with two different oscillation modes are present. A new type of "Rocking" mode is discovered in the present study.
Simulation Of Single Bubble Evaporation In A Microchannel In Zero Gravity With Thermocapillary Effect

Wei Li,Yang Luo,Jingzhi Zhang,W. J. Minkowycz

DOI: https://doi.org/10.1115/1.4040147

2018-01-01

Abstract:This paper presents fundamental research on the hydrodynamics and heat transfer surrounding a single elongated bubble during flow boiling in a circular microchannel. A continuum surface force (CSF) model based on the volume of fluid (VOF) method is combined with the thermocapillary force to explore the effects of thermocapillarity for flow boiling in microchannels. To validate the self-defined codes, a two-phase thermocapillary-driven flow and a Taylor bubble growing in a capillary tube are studied. Results of both test cases show good convergence and agreement with data from the earlier literature. The bubble motion and the local heat transfer coefficient (HTC) on the heated wall with respect to time are discussed. It is found that for large Marangoni number (case 3), variation of surface tension has affected the bubble shape and temperature profile. The thermocapillary effect induces convection in a thin liquid film region, which augments the HTCs at specified positions. The numerical investigation also shows that the average HTC increased by 6.7% in case 3 when compared with case 1. Thus, it is very important to study further the effects of themocapillarity and the Marangoni effect on bubble growth in microchannels.
Dynamics and Diffusion Mechanism of Low-Density Liquid Silicon.

B. Shen,Z. Y. Wang,F. Dong,Y. R. Guo,R. J. Zhang,Y. X. Zheng,S. Y. Wang,C. Z. Wang,K. M. Ho,L. Y. Chen

DOI: https://doi.org/10.1021/acs.jpcb.5b09138

2015-01-01

Abstract:A first-order phase transition from a high-density liquid to a low-density liquid has been proposed to explain the various thermodynamic anomies of water. It also has been proposed that such liquid-liquid phase transition would exist in supercooled silicon. Computer simulation studies show that, across the transition, the diffusivity drops roughly 2 orders of magnitude, and the structures exhibit considerable tetrahedral ordering. The resulting phase is a highly viscous, low-density liquid silicon. Investigations on the atomic diffusion of such a novel form of liquid silicon are of high interest. Here we report such diffusion results from molecular dynamics simulations using the classical Stillinger-Weber (SW) potential of silicon. We show that the atomic diffusion of the low-density liquid is highly correlated with local tetrahedral geometries. We also show that atoms diffuse through hopping processes within short ranges, which gradually accumulate to an overall random motion for long ranges as in normal liquids. There is a close relationship between dynamical heterogeneity and hopping process. We point out that the above diffusion mechanism is closely related to the strong directional bonding nature of the distorted tetrahedral network. Our work offers new insights into the complex behavior of the highly viscous low density liquid silicon, suggesting similar diffusion behaviors in other tetrahedral coordinated liquids that exhibit liquid-liquid phase transition such as carbon and germanium.
A containerless levitation setup for liquid processing in a superconducting magnet.

Hui-Meng Lu,Da-Chuan Yin,Hai-Sheng Li,Li-Qiang Geng,Chen-Yan Zhang,Qin-Qin Lu,Yun-Zhu Guo,Wei-Hong Guo,Peng Shang,Nobuko I Wakayama

DOI: https://doi.org/10.1063/1.2980383

IF: 1.6

2008-01-01

Review of Scientific Instruments

Abstract:Containerless processing of materials is considered beneficial for obtaining high quality products due to the elimination of the detrimental effects coming from the contact with container walls. Many containerless processing methods are realized by levitation techniques. This paper describes a containerless levitation setup that utilized the magnetization force generated in a gradient magnetic field. It comprises a levitation unit, a temperature control unit, and a real-time observation unit. Known volume of liquid diamagnetic samples can be levitated in the levitation chamber, the temperature of which is controlled using the temperature control unit. The evolution of the levitated sample is observed in real time using the observation unit. With this setup, containerless processing of liquid such as crystal growth from solution can be realized in a well-controlled manner. Since the levitation is achieved using a superconducting magnet, experiments requiring long duration time such as protein crystallization and simulation of space environment for living system can be easily succeeded. (C) 2008 American Institute of Physics. [DOI: 10.1063/1.2980383]
A sessile drop approach for studying 4H-SiC/liquid silicon high-temperature interface reconstructions

Xinming Xing,Takeshi Yoshikawa,Olga Budenkova,Didier Chaussende

DOI: https://doi.org/10.1007/s10853-021-06816-y

IF: 4.5

2022-01-01

Journal of Materials Science

Abstract:Accurate description, understanding and control of the high temperature interface behavior between the SiC single crystal and liquid phase is critical for further development of SiC solution growth. The different parameters which create morphological instabilities, such as step bunching, micro-faceting and solvent trapping, remain unclear because they are very difficult to address in high temperature experiments. We combined experiments and numerical simulation to design a specific sessile drop approach where the liquid is removed before cooling down. The advantage of this method that it activates or suppresses the solute (carbon) transport by an AC magnetic field and thus separates the physical–chemical and hydrodynamic contributions. The method was demonstrated through observation of the morphological evolution of a 4°off 4H-SiC (0001) surface in contact with pure liquid silicon at 1600 °C according to the time factor. Several parasitic effects were also analyzed and suppressed in order to obtain a well-controlled uniform interface.

materials science, multidisciplinary
Microscale Confinement and Wetting Contrast Enable Enhanced and Tunable Condensation.

Xiao Yan,Feipeng Chen,Chongyan Zhao,Xiong Wang,Longnan Li,Siavash Khodakarami,Kazi Fazle Rabbi,Jiaqi Li,Muhammad Jahidul Hoque,Feng Chen,Jie Feng,Nenad Miljkovic

DOI: https://doi.org/10.1021/acsnano.2c02669

IF: 17.1

2022-01-01

ACS Nano

Abstract:Dropwise condensation represents the upper limit of thermal transport efficiency for liquid-to-vapor phase transition. A century of research has focused on promoting dropwise condensation by attempting to overcome limitations associated with thermal resistance and poor surface-modifier durability. Here, we show that condensation in a microscale gap formed by surfaces having a wetting contrast can overcome these limitations. Spontaneous out-of-plane condensate transfer between the contrasting parallel surfaces decouples the nanoscale nucleation behavior, droplet growth dynamics, and shedding processes to enable minimization of thermal resistance and elimination of surface modification. Experiments on pure steam combined with theoretical analysis and numerical simulation confirm the breaking of intrinsic limits to classical condensation and demonstrate a gap-dependent heat-transfer coefficient with up to 240% enhancement compared to dropwise condensation. Our study presents a promising mechanism and technology for compact energy and water applications where high, tunable, gravity-independent, and durable phase-change heat transfer is required.
A Thermocapillary Convection Experiment in Microgravity

Y. Kamotani,S. Ostrach,A. Pline

DOI: https://doi.org/10.1115/1.2822621

1995-08-01

Journal of Heat Transfer

Abstract:Results are reported of the Surface Tension Driven Convection Experiment (STDCE) aboard the USML-1 Spacelab, which was launched on June 25, 1992. In the experiment, 10 cSt silicone oil was placed in an open 10-cm-dia circular container, which was 5 cm deep. The fluid was heated either by a cylinderical heater (1.11 cm diameter) located along the container centerline or by a CO2 laser beam to induce thermocapillary flow. Several thermistor probes were placed in the fluid to measure the temperature distribution. The temperature distribution along the liquid-free surface was measured by an infrared imager. Tests were conducted over a range of heating powers, laser-beam diameters, and free surface shapes. An extensive numerical modeling of the flow was conducted in conjunction with the experiments. Some results of the temperature measurements with flat free surfaces are presented in this paper and they are shown to agree well with the numerical predictions.
Creating lifting force in liquids via thermal gradients

Qingwen Dai,Jin Yan,Arman Sadeghi,Wei Huang,Xiaolei Wang,M.M. Khonsari

DOI: https://doi.org/10.1016/j.jcis.2022.09.002

IF: 9.9

2022-09-24

Journal of Colloid and Interface Science

Abstract:In this paper, we explore a concept and present the first experimental evidence to show that it is possible to form a stable liquid film and create lifting force at the interface via thermal gradient to minimize interfacial rubbing of surfaces and the associated wear. The approach is based on manipulating the flow behavior via thermocapillary, which describes how a liquid can be made to flow from warm to cold regions purely by inducing a thermal gradient. We show that liquid bridges between two parallel plates can be manipulated and stabilized under a combined effect of the thermocapillary flow and the Couette flow, which describes the motion of a viscous fluid between two parallel plates in a relative sliding motion. The equilibrium stage is confirmed under different experimental conditions of a thermal gradient, interfacial gap, liquid viscosity, and liquid bridge volume. A strategy is proposed to control liquid motion and create lifting force between two plates. A theoretical model is also presented to illustrate the principle of the equilibrium stage. Creating lifting forces at the interface offers a new thermo-hydrodynamic tool for manipulating liquids behavior. This approach has the potential for controlling liquid motion in mechanical components and nature.

chemistry, physical

Reduction of Thermocapillary Convection in a Silicon Liquid Bridge by a Non-Contaminating Method

Numerical Investigation of the Effect of Rotation on the Oscillatory Thermocapillary Convection and Dopant Transport in a Silicon Liquid Bridge

Stability of buoyancy–thermocapillary convection in molten silicon liquid bridge between two disks with different radii under gravity

Effect of Liquid Encapsulation on Thermocapillary Convection in Molten Liquid under Microgravity Condition

Reorientation of Hydrogen Bonds Renders Unusual Enhancement in Thermal Transport of Water in Nanoconfined Environments

Effect of a Uniform Axial Magnetic Field on the Spatiotemporal Evolution of Thermocapillary Convection in a High Prandtl Fluid Under Microgravity

Heat Flow Control and Segregation in Directional Solidification: Development of an Experimental and Theoretical Basis for Bridgman-Type Growth Experiments in a Microgravity Environment

Mesoscale Simulation of Marangoni Convection about a Vapor Bubble in a Liquid with Temperature Gradients under Microgravity Conditions

Influence of Gravitational Tilt on the Thermocapillary Convection in a Non-Axisymmetric Liquid Bridge

Effect of volume ratio on thermocapillary convection in annular liquid pools in space

Experimental study of the effect of noncondensables on buoyancy-thermocapillary convection in a volatile low-viscosity silicone oil

Suppression of Melt Convection in a Proposed Bridgman Crystal Growth System

Flow instabilities in thermocapillary liquid bridges between two coaxial disks with different radii

Oscillatory Thermocapillary Convection in Deformed Half Zone Liquid Bridges of Low Prandtl Number Fluids

Simulation Of Single Bubble Evaporation In A Microchannel In Zero Gravity With Thermocapillary Effect

Dynamics and Diffusion Mechanism of Low-Density Liquid Silicon.

A containerless levitation setup for liquid processing in a superconducting magnet.

A sessile drop approach for studying 4H-SiC/liquid silicon high-temperature interface reconstructions

Microscale Confinement and Wetting Contrast Enable Enhanced and Tunable Condensation.

A Thermocapillary Convection Experiment in Microgravity

Creating lifting force in liquids via thermal gradients