Abstract:Internal metallurgical defects and poor mechanical properties and surface quality of the formed parts are the most important challenges of metal micro-droplets deposition manufacturing technology. Lack of strong coalescence between neighboring droplets and the blocking effects of periodic ripples on the fusion process are major sources of abovementioned problems. To address this issue, a tungsten inert gas (TIG) welding arc was introduced to pre-melt the material below the droplet impacting location, thus, one droplet train will be deposited on a curved molten pool surface to fabricate deposited layers in an additive approach. In the present work, a numerical model based on the computational fluid dynamics (CFD) method was developed to investigate the dynamic behaviors of successive droplets' impact and coalescence on the molten pool created by a tilted TIG welding arc, and focuses on the effect of the offset distance between the impacting point of droplet and the longitudinal plane of molten pool on the deposition morphology and the impact-induced molten pool behaviors. The simulated tracks exhibit regular scaly shapes at different offset distances, which is validated against the corresponding experiments. The results indicated that as the lateral offset distance increases, the symmetric spreading and recoiling of the subsequent droplets on the pre-existing bead will be broken due to the inclined and curved solidification front morphologies, the inclined front morphologies are caused by the increased growth rate of the solidification front at the impact zone. With an increased lateral offset distance, the volume of the molten pool decreases, the width of the rear molten pool increases slightly. The calculated solidification parameters are found to be dependent of the offset distance, and vary significantly at the onset of solidification at different portions of the molten pool. The scientific findings provide useful insights for further researches of TIGassisted DDM.

Molten Pool Dynamics and Particle Migration Behavior During TIG-assisted Droplet Deposition Manufacturing of SiC Particle-reinforced Aluminum Matrix Composites

Droplet Impact-Induced Molten Pool Dynamics and Particle Migration Patterns During TIG-assisted Droplet Deposition Manufacturing of SiC Particle-Reinforced Al–Si Alloy

Numerical Analysis of Particulate Migration Behavior Within Molten Pool During TIG-Assisted Droplet Deposition Manufacturing of SiC Particle-Reinforced Aluminum Matrix Composites.

Offset impacting of a liquid aluminum droplet train on a molten pool on a horizontally moving substrate during TIG-assisted droplet deposition manufacturing

Influence of Droplet Size and Ejection Frequency on Molten Pool Dynamics and Deposition Morphology in TIG-aided Droplet Deposition Manufacturing

Thermal evolution behavior and fluid dynamics during laser additive manufacturing of Al-based nanocomposites: Underlying role of reinforcement weight fraction

Thermal-fluid dynamic behavior and its effect on particle distribution and solidification characterization during the laser melting deposition of Ti-based composites

Comparative Study of Solidification Behaviors of Weld Pool Through Modelling of Heat Transfer and Fluid Flow During Single- and Multiplelayer Deposits of 2319-Aluminum Alloy Based on Variable Polarity Gas Tungsten Arc Welding

Numerical Simulation of Microstructure of Al-Si/Sicp Composites During Stir Casting Process with Particle Pushing Model

Modeling on Molten Pool Transport in Laser Deposition Processes by Lattice Boltzmann Method

Dispersion of reinforcing micro-particles in the powder bed fusion additive manufacturing of metal matrix composites

Numerical simulation of microstructure for stir casting of Al-Si/SiC p composites with particle pushing model

Molten pool flow behavior and influencing factors in electron beam selective melting of IN738 superalloy

3D microstructure simulation of stir casting SiCp/Al-7.0%Si composites

Simulation of Temperature Distribution and Discharge Crater of SiCp/Al Composites in a Single-Pulsed Arc Discharge

Investigation of Droplet+Arc Deposition Additive Manufacturing with WCp Simultaneous Reinforcement for Aluminum Alloy

Evolution of molten pool during selective laser melting of Ti–6Al–4V

Modeling of droplet short-circuiting transfer and simulation of three-dimensional transient behavior of molten pool

Modeling of Dendritic Growth and Particle Pushing/engulfment in the Solidification of Aluminum Matrix Composites with the CA-LBM-IMB Method

Fluid Thermodynamic Simulation of Ti-6Al-4V Alloy in Laser Wire Deposition

Numerical Simulation of Arc and Droplet Behaviors in TIG-MIG Hybrid Welding