Abstract:The Journal of Strain Analysis for Engineering Design, Ahead of Print. In the present work, the process chain in tube production by roll forming of the steel 34MnB5 was examined in more detail. The process chain consisting of the steps (i) roll forming, (ii) HFI welding, and then (iii) straightening and final calibration was mapped using the finite element method. In addition to the pipe geometry, the residual stress distribution was considered as an essential target value for the assessment of the performance of the tubes under service conditions. The objective of the project is to describe the manufacturing process and thus the processing induced residual stress distributions as realistically as possible. For a more detailed characterization of the process and above all for the validation of the numerical simulations, experimental residual stress analyses were carried out for the final state of the tubes using complementary analysis methods. The contour method was used to determine the 2D-distribution of residual stresses across the transverse and longitudinal sections of the manufactured pipes. These measurements were supplemented by local residual stress analyses using the incremental hole drilling method and X-ray residual stress analyses. The work thus pursues both a methodical approach to the analysis of the internal stresses induced by the process using complementary methods and also a manufacturing approach to the analysis and evaluation of the production chain. In particular for the axial components of the residual stresses, it can be shown that experimentally determined residual stresses correlate well with the numerically calculated values. The contour method is excellently suited to monitor the uneven distribution of the internal stresses over the pipe cross-section. The results of the simulation show that the overall residual stress distribution that is determined using the contour method mainly results from the plastic strains introduced by the roll forming process. X-ray and hole drilling analyses are shown to be more suitable for measuring locally present residual stresses at defined positions on the outer tube surface. In this way it can be shown that the simulation approach described provides an accurate model of the process.

Thermomechanical History Measurements on Type 304L Stainless Steel Pipe Girth Welds

A study of local mechanical properties of 304L SS welded joints subjected to cyclic straining using depth-sensing instrumented indentation

Use of instrumented indentation testing to study local mechanical properties of 304L SS welded joints subjected to low-cycle fatigue loadings

Thermal, metallurgical and mechanical analysis of circumferentially multi-pass welded P92 steel pipes

Inhomogeneous Strain Behaviors of the High Strength Pipeline Girth Weld under Longitudinal Loading

Investigation of the tensile strain response of the girth weld of high-strength steel pipeline

Prediction of Residual Stress Distributions in Welded Sections of P92 Pipes with Small Diameter and Thick Wall Based on 3D Finite Element Simulation

Residual Stress Formation and Distortion in Austenitic AISI304 Steel Pipe Weldment with Consideration of Latent Heat using Novel Prescribed Weld Temperature

Thermal-Mechanical Fatigue Behavior of P92 T-Piece Pipe

Residual stress simulation in thin and thick-walled stainless steel pipe welds including pipe diameter effects

Residual-Stress, Material Characterization in P22 HRSG-Pipeline Butt Joint

Effect of Process Parameters on Welding Residual Stress of 316L Stainless Steel Pipe

Comparative study on girth weld-induced residual stresses between austenitic and duplex stainless steel pipe welds

Analysis and mitigation of the bending deformation in girth-welded slender pipes with numerical modelling and experimental measurement

Effects of Welding and Constraint Conditions on the Welding Residual Stress and Hardness of Type 316 Stainless Steel Pipe

Sensitivity Analysis of History Dependent Material Mechanical Models for Numerical Simulation of Welding Process

Experimental and numerical analysis of residual stresses induced by the manufacturing process of longitudinal welded tubes

Mechanical behaviour of longitudinal lap-welded joints of high strength steel: Experimental and numerical analysis

Three-dimensional finite element analysis of residual stresses in dissimilar steel pipe welds

Failure Bending Stresses for Small Diameter Thick-Wall Pipes

Microstructural and Performance Analysis of TP304H/T22 Dissimilar Steel Welded Joints