Abstract:Ti-6.5Al-2Zr-1Mo-1V/TiB metal matrix composites with 3 wt.% of TiB2 were obtained using vacuum arc melting and spark plasma sintering methods and compared with an unreinforced Ti-6.5Al-2Zr-1Mo-1V alloy. The microstructures of the unreinforced Ti6.5Al-2Zr-1Mo-1V alloy in the as-cast and as-sintered conditions were quite typical and consisted of colonies of α-lamellae embedded in the β matrix. The microstructure of the as-cast Ti-6.5Al-2Zr-1Mo-1V/TiB composite composed of TiB fibers randomly distributed within the two-phase α/β matrix, while the as-sintered composite had a network-like microstructure, in which areas of the two-phase α/β matrix were delineated by walls of TiB fibers. At room temperature, the yield strength of the as-cast and as-sintered Ti-6.5Al-2Zr-1Mo-1V alloy were 800 and 915 MPa, respectively, with a plasticity of 18% in both conditions. The addition of TiB fibers contributed to a ~40 and 50% strength increment, with values of 1100 and 1370 MPa for the as-cast and as-sintered composites, respectively. In the as-sintered composite, the strengthening effect reduced at 400 °C and almost disappeared at elevated temperatures of 800–950 °C. The as-cast composite showed much higher strength during warm and hot deformation—at 800–950 °C, the yield strength of the as-cast composite was 50% higher compared to the Ti-6.5Al-2Zr-1Mo-1V unreinforced alloy. A higher rate and degree of globularization were established for the as-cast composite compared to the unreinforced alloy. For the as-sintered composite, a noticeably lower rate and degree of globularization was shown. During hot compression of the as-cast composite, TiB fibers reoriented towards the metal flow direction, while the network microstructure formed in the as-sintered composite transformed into clusters of borides unevenly distributed within the matrix. Based on the obtained results, the apparent activation energy of plastic deformation was calculated, and the operating deformation mechanisms were discussed both for the as-cast and as-sintered composites. The Arrhenius flow stress model and the dynamic material model were used to evaluate the deformation behavior of composites beyond the experimentally studied temperatures and strain rates.

A Physically-Based Model for Elevated Temperature Strength Prediction of (tibw + (ti, Zr)5Si3)/Ti-6.5Al-2Zr-1Mo-1V Composite

A physically-based model for elevated temperature strength prediction of (TiBw + (Ti, Zr) 5 Si 3 )/Ti-6.5Al-2Zr-1Mo-1V composite

High Temperature Tensile Properties of in Situ TiBw/Ti6Al4V Composites with a Novel Network Reinforcement Architecture

Microstructure Regulation and Strength-Elongation Synergy of the Near Alpha TZAM Alloy Via Thermomechanical Processing

Thermal stability and its effects on the mechanical properties of rapidly solidified Al-Ti alloys

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Experimental Characterization and Yield Strength Model for Process-Structure-Property of Selective Laser Melted 316L

Process-structure-property Modeling for Postbuild Heat Treatment of Powder Bed Fusion Ti-6Al-4V

Thermomechanical Processing of a Near-α Ti Matrix Composite Reinforced by TiBw

Predicting The Tensile Behavior Of Ti-6.6al-3.3mo-1.8zr-0.29si Alloy Via The Temperature-Dependent Crystal Plasticity Method

New Numerical Method Based on Linear Damage Evolution Law for Predicting Mechanical Properties of TiB2/6061Al

Microstructure Evolution and Mechanical Behavior of TiB-Reinforced Ti-6.5Al-2Zr-1Mo-1V Matrix Composites Obtained by Vacuum Arc Melting and Spark Plasma Sintering

Effect of Solution Temperature on Microstructure and Mechanical Properties of Ti–5Al5Mo5V3Cr1Zr Alloy

High fatigue performance and microscopic mechanisms of in-situ TiB 2 /7050Al composite at different temperatures

Microstructural based constitutive modeling and subsurface microhardness prediction in machining of network-structured TiBw/TA15 composites

Effect of microstructures on mechanical properties of Ti‐6.5Al‐2Sn‐4Zr‐4Mo‐1W‐0.2Si alloy

Network-Strengthened Ti-6Al-4V/(TiC+TiB) Composites: Powder Metallurgy Processing and Enhanced Tensile Properties at Elevated Temperatures

Microstructures and mechanical properties of (TiBw+Ti 5 Si 3 )/TC11 composites fabricated by hot isostatic pressing and subjected to 2D forging

The microstructure and martensitic transformation of Ti–V–Al–B elevated temperature shape memory alloy tailored by thermo-mechanical treatment

High temperature performance of TiB/(Ti-6.5Al-2Zr-1Mo-1V-0.5Si) composites affected by the TiB architecture

Effect of Heat Treatment on the Microstructure and Mechanical Properties of Additive Manufactured Ti-6.5Al-2Zr-1Mo-1V Alloy