Abstract:Purpose: Active matrix flat-panel imagers (AMFPIs) incorporating thick, segmented scintillators have demonstrated order-of-magnitude improvements in detective quantum efficiency (DQE) at radiotherapy energies compared to systems based on conventional phosphor screens. Such improved DQE values facilitate megavoltage cone-beam CT (MV CBCT) imaging at clinically practical doses. However, the MV CBCT performance of such AMFPIs is highly dependent on the design parameters of the scintillators. In this paper, optimization of the design of segmented scintillators was explored using a hybrid modeling technique which encompasses both radiation and optical effects. Methods: Imaging performance in terms of the contrast-to-noise ratio (CNR) and spatial resolution of various hypothetical scintillator designs was examined through a hybrid technique involving Monte Carlo simulation of radiation transport in combination with simulation of optical gain distributions and optical point spread functions. The optical simulations employed optical parameters extracted from a best fit to measurement results reported in a previous investigation of a 1.13 cm thick, 1016 μm pitch prototype BGO segmented scintillator. All hypothetical designs employed BGO material with a thickness and element-to-element pitch ranging from 0.5 to 6 cm and from 0.508 to 1.524 mm, respectively. In the CNR study, for each design, full tomographic scans of a contrast phantom incorporating various soft-tissue inserts were simulated at a total dose of 4 cGy. Results: Theoretical values for contrast, noise, and CNR were found to be in close agreement with empirical results from the BGO prototype, strongly supporting the validity of the modeling technique. CNR and spatial resolution for the various scintillator designs demonstrate complex behavior as scintillator thickness and element pitch are varied--with a clear trade-off between these two imaging metrics up to a thickness of ~3 cm. Based on these results, an optimization map indicating the regions of design that provide a balance between these metrics was obtained. The map shows that, for a given set of optical parameters, scintillator thickness and pixel pitch can be judiciously chosen to maximize performance without resorting to thicker, more costly scintillators. Conclusions: Modeling radiation and optical effects in thick, segmented scintillators through use of a hybrid technique can provide a practical way to gain insight as to how to optimize the performance of such devices in radiotherapy imaging. Assisted by such modeling, the development of practical designs should greatly facilitate low-dose, soft tissue visualization employing MV CBCT imaging in external beam radiotherapy.

Optimization for Energy Response Characteristics of Plastic Scintillators Based on Genetic Algorithm

A Real-Time Energy Response Correction Method for Cs3Cu2I5:Tl Scintillating Dosimeter

Generalized Method for the Optimization of Pulse Shape Discrimination Parameters

A study on “position-energy” response correction method based on monolithic crystal coupled SiPM array

Design optimization of JUNO-TAO plastic scintillator with WLS-fiber and SiPM readout

Zn (ii)‐doped Cesium Copper Halide Nanocrystals with High Quantum Yield and Colloidal Stability for High‐Resolution X‑Ray Imaging

In-Silico Optimisation of Tileable Philips Digital SiPM Based Thin Monolithic Scintillator Detectors for SPECT Applications

An electronic energy compensation method for flattening the energy response of SiPM-GGAG:Ce,B based gamma detector

Development of a Light Yield Calibration Method for Μsr Detectors Based on Compton Edge Location

Optimization of the design of thick, segmented scintillators for megavoltage cone-beam CT using a novel, hybrid modeling technique

Design and Optimization of Direct-Conversion Photon-Counting Detector for Dual-Energy Ct Imaging

Low Energy X-Ray Imaging Using Plastic Scintillating Fiber: A Simulation Study

A Phoswich Composed Of Csi:Na And Labr3:Ce To Improve The Low Energy Response Of Labr3:Ce

Optimization of Energy Compensation Layered Structure of Geiger- Müller Counters

Simulation study on detection efficiency of plastic scintillating fiber under γ-ray radiation

Enhancement of the Energy Resolution of CsI(Na) Scintillators by Photonic Crystals Prepared with Dry-Transfer Technique.

Optimization of the design of Gas Cherenkov Detectors for ICF diagnosis

Combinatorial approach to bulk detector material engineering: Application to rapid NaI performance optimization via multi-element doping/co-doping strategy

Turning Nonemissive CsPb 2 Br 5 Crystals into High-Performance Scintillators through Alkali Metal Doping

MONTE CARLO CALCULATION AND COMPARISON OF GAMMA/NEUTRON DISCRIMINABILITY OF SOME SCINTILLATORS