Abstract:Propose a rolling method to efficiently prepare fiber metal laminates. The surface of Al alloy sheets is treated with laser and coupling agent to achieve the purpose of toughening interface of composite laminates. In this study, a highly efficient method for preparing Al/CFRTP/Al composite laminates by roller preparation was proposed. Three different surface treatments, namely, anodic oxidation, laser texture and surface modification, were used to improve the strength of the metal‐fiber interface. Results show that composite laminates can be prepared efficiently by using reasonable roll pressing technology. The composite laminates with a thickness of 3 mm has good shear strength when the reduction amount is 0.02 mm. Laser texturing increases the contact area at the laminate interface. The surface roughness of Al alloy sheet is improved after laser texture. Moreover, the matrix in the fiber layer of the laminate can be embedded in the gullies formed by the laser texture to form a mechanical interlocking structure. The shear strength of the laminates was further increased when the laser scanning spacing was 2 mm. The highest shear strength of the laminate is 52.4 MPa after using a coupling agent to modify the surface of the Al alloy sheet. X‐ray photoelectron spectroscopy analysis showed that a new chemical bond was generated at the interface between CFRTP and the Al alloy sheet modified with silane coupling agent, thereby forming a molecular bridge among different materials. Mechanical interlocking structure and the generation of new chemical bonds cause the interface to need to absorb more energy during the failure process, which is conducive to the improvement of the interface strength. Highlights Propose roller pressing to prepare Al/CFRTP/Al composite laminates. Effect of laser texture of the laminates interface is clarified. Mechanism of coupling agents at the interface has been elucidated. Efficient preparation of thermoplastic fiber metal laminates has been achieved.

Process Parameter Optimization for Laser Welded Cfrtp/Tc4 Composite Joint with Surface Modification of MAO and Mirco-Texture

Improvement of laser welded TC4/CFRTP joint strength by combination of surface modification of MAO and laser texturing

Effect of Laser Micro-Texturing on Laser Joining of Carbon Fiber Reinforced Thermosetting Composites to TC4 Alloy

Nanosecond laser ablation for improving the strength of CFRTP and aluminum alloy adhesively bonded joints

Enhancing Bond Strength Between Carbon Fiber Reinforced Thermoplastic and Aluminum Alloys Through Laser Surface Treatment

Influence of laser texturing on the properties of fusion joints between aluminum alloys and carbon fiber reinforced thermoplastic composites

Effect of laser texturing on mechanical strength and microstructural properties of hot-pressing joining of carbon fiber reinforced plastic to Ti6Al4V

Effect of surface texture spacing on interface heat transfer and tensile property of laser‐welded steel/ CFRTP joint

Laser joining of CFRTP to titanium alloy via laser surface texturing

Parameter optimization of friction stir spot welded Al 6061 and CFRTP PA6 with surface treatment and interfacial adhesion

Optimization of microstructural morphology via laser processing to enhance the bond strength of Al-CFRP

Laser Direct Joining of CFRTP and Aluminium Alloy with a Hybrid Surface Pre-Treating Method

Effects of laser hybrid interfacial pretreatment on enhancing the carbon fiber reinforced thermosetting composites and TC4 alloy heterogeneous joint

Effect of anodizing pretreatment on laser joining stainless steel to CFRTP

Surface pre-oxidation for enhancing laser assisted joining between carbon fiber reinforced thermoplastic composites and AZ31B Mg alloy

The effect of groove texturing direction on laser joining of titanium alloy to CFRTP

Rolling preparation process and interface toughening mechanism of Al/CFRTP/Al composite laminates

Biomimetic papilla texture by femtosecond laser for high-strength CFRTP/A6061-T6 FSSW hybrid structures

Carbon fiber reinforced thermoplastic composites and TC4 alloy laser assisted joining with the metal surface laser plastic-covered method

Influence of process parameters on the joint characteristics during laser joining of aluminium alloy and CFRTP

Influence of processing parameters on joint shear performance in laser direct joining of CFRTP and aluminum alloy