Abstract:Cold spray deposition has emerged as a promising method for applying protective coatings in the nuclear industry, particularly for enhancing the accident tolerance of fuel assemblies. In this process, helium gas is often used to propel solid powder particles towards the target substrate, however, nitrogen gas is also considered due to its significantly lower cost. In this study, we investigate the influence of nitrogen and helium gas as propellants on the properties and microstructure of pure chromium (Cr) coatings on zirconium (Zr) alloy cladding tubes. Employing Scanning Electron Microscopy (SEM) and electron and x-ray diffraction techniques (EBSD, XRD), we explore the structural characteristics of the coatings. Additionally, in-situ SEM tensile testing at room temperature, coupled with Digital Image Correlation (DIC), is utilized to assess the coating cracking behaviour. Our findings reveal distinct differences in coating morphology and residual stress between nitrogen and helium propelled Cr coatings. The nitrogen-propelled coating exhibits a more porous structure with smoother coating/substrate interfaces and lower compressive residual stress compared to the helium-propelled one. This results in earlier strain-induced crack initiation and higher crack density at lower strains (0.5–2%). However, at higher strains (2–5%), both coatings demonstrate identical crack saturation densities (saturated number of cracks per unit length), accompanied by similar crack toughening mechanisms and evidence of shear strain bands at intercrack regions, indicative of plasticity onset.

NUMERICAL SIMULATION AND EXPERIMENTAL RESEARCH OF CR–AG COATINGS FOR THE ITER SCC THERMAL SHIELD

Preparation of Al-Cr-Fe Coatings by Heat Treatment of Electrodeposited Cr/Al Composite Coatings

Study of Atomic Sputtering and Transport Dynamics by Monte Carlo Simulation

Influence of Original Powders on the Microstructure and Properties of Thermal Barrier Coatings Deposited by Supersonic Atmospheric Plasma Spraying, Part Ii: Properties

Microstructure, formation mechanism and properties of plasma-sprayed Cr7C3—CrSi2—Al2O3 coatings

Microstructural Design and Oxidation Resistance of Conicraly Alloy Coatings in Thermal Barrier Coating System

Fundamental understanding on the microstructure and corrosion resistance of Cr-(Cr, Al)2O3 composite coatings in-situ synthetized by reactive plasma spraying

An Orthogonal Experimental Study on the Preparation of Cr Coatings on Long-Size Zr Alloy Tubes by Arc Ion Plating

Numerical and Experimental Investigation for Application of CoNiCrAlY Coatings by HVAF

A study on protection behavior of inorganic coating prepared by magnetron sputtering technology for electrochemical migration corrosion failure of SAC305 alloy

Study on microstructure evolution and reaction mechanism of in-flight Ti–Si–C agglomerates during reactive plasma spraying using in situ water quenching

Microstructure and mechanical performance of cold spray Cr coatings

Study on Comparison of Four Different Coatings Onto Crystallizer

Performance in Resistance to Surface Fatigue for Cr 3 C 2 –25%NiCr Coatings by Plasma Spray and CDS Spray

Effect of suspension plasma spraying power on the microstructure and properties of Cr 2 AlC coatings

Study of the Mechanical Properties and Thermal Control Performance of Plasma-Sprayed Alumina Coating on Aluminum Alloy Surface

Investigation of stress field and failure mode of plasma sprayed Al2O3–13%TiO2 coatings under thermal shock

Finite element simulation of thermal stress in RF magnetron sputtered SiC coating as tritium penetration barrier

Influence of atomic migration mode at different temperatures on the microstructure, mechanical and cavitation erosion behaviors of Co-based alloy coating

Study on Microstructure and Properties of Cr3C2/Fe Coating Prepared by Arc Spraying on Copper Surface

Cold spray for production of in-situ nanocrystalline MCrAlY coatings – Part I: Process analysis and microstructure characterization