Abstract:Abstract Within the certification process of aircraft, tests under specific icing conditions are required. For such safety relevant tests—which are performed under defined and repeatable test conditions—specially equipped Icing Wind Tunnels (IWT) are required. In such IWTs, supercooled water droplets are created with the aid of a spray system injecting pre-tempered water droplets of specific diameters into the free stream air flow. Especially tests with a droplet size up to 2mm (Supercooled Large Droplets - SLD s) are of great importance. SLDs are difficult to generate under laboratory conditions in IWT since usually the available droplet flight time from the injection location to the impact position on the test object is insufficient to reliably cool down a droplet at least to freezing temperature. To investigate the limitations associated with the application of SLD, the current work provides a method to allow detailed insight into the behavior of droplets on the path from the injection spray nozzle to the test section. In this work a state space model of a single droplet is derived that combines the kinetic aspects, thermal properties as well as the governing differential equations for motion, convective heat transfer at the droplet surface and heat conduction inside the droplet. Beside the states for the droplet’s position and velocity in space, the state space vector comprises various fluid and thermodynamic parameters. The droplet-internal temperature distribution is modelled by a discrete one-dimensional spherical shell model that also incorporates the aggregate phase (freezing mass fraction) at each shell node. This approach allows, therefore, the simulation of potential droplet phase change processes (freezing/melting) as well. With the model at hand, the influence of various boundary conditions (initial droplet temperature, flow field, ambient air temperature, etc.) can be determined and evaluated. As a result, concrete measures to achieve a desired operating condition (e.g. droplet temperature at the test object) for various model assumptions can be derived. In addition, the simulation model facilitates the prediction of the droplet diameter threshold for ensuring a supercooled state upon the impact on the test object. The governing theoretical influences are described, and various simulation results for representative test conditions that occur at the Rail-Tec-Arsenal (RTA) in Vienna are presented.

Numerical Simulation of Trace Water Icing Characteristics on Airfoil Under Cryogenic Conditions

Experimental study of frosting characteristics of trace water vapor under cryogenic wind tunnel conditions

Mechanisms of Trace Water Vapor Frosting on a Cryogenic Surface in Nitrogen Gas Flow

Mechanisms of Trace Water Vapor Desublimation over Airfoil in Transonic Cryogenic Wind Tunnels

Numerical Investigation of Wind Turbine Airfoil Icing and Its Influencing Factors under Mixed-Phase Conditions

Numerical Simulation of Freezing Process of a Sessile Supercooled Water Droplet on a Cold Wall

Numerical Investigation of Nitrogen Condensation Flow over Airfoil in Cryogenic Wind Tunnel

Research and Development of a Small-Scale Icing Wind Tunnel Test System for Blade Airfoil Icing Characteristics

Numerical simulation of icing effect on aerodynamic characteristics of a wind turbine blade

Numerical investigation on the tracer followability of nitrogen droplets over the airfoil in cryogenic wind tunnel

Numerical Simulation of Ice Crystal Supercooled Droplet Mixed Phase Icing Based on the Improved Messinger Model

Numerical Simulation of Water Film Flow and Breakup on Anti-Icing Surface

Numerical Simulation of Hot Air Anti-icing Charateristics of an Aero-engine Strut

Kinetic and thermal simulation of water droplets in icing wind tunnels

Numerical and experimental investigation of the supercooled large droplets icing of rotating spinner

Influence of Air Flow Field Computation on an Ice Accretion Simulation of Airfoils

Numerical Simulation of Aircraft Icing under Local Thermal Protection State

Study of Solidification and Microstructure Characteristics for Aircraft Icing

Numerical simulation for in-cloud icing of three-dimensional wind turbine blades

Frost Layer Growth Behavior Study on a Cryogenic Surface with Water Vapor Content <1000 Ppmv

Experimental Validation and Tightly Coupled Numerical Simulation of Hot Air Anti-Icing System Based on an Extended Mass and Heat Transfer Model