Abstract:Polypropylene double‐grafted maleic anhydride and bisphenol A epoxy resin (PPg‐M‐E) was prepared and used as compatibilizer for PP/PET blends. The thermomechanical and morphology of the composites were characterized. The results show that PP‐g‐M‐E increased the interfacial interaction between the two phases and improves the mechanical properties and thermal stability of the blend system. Polypropylene double‐grafted maleic anhydride and bisphenol A epoxy resin (PP‐g‐M‐E) was successfully prepared by a single‐step method and characterized by Fourier‐transform infrared spectroscopy. Subsequently, it was employed as a compatibilizer to fabricate polypropylene (PP)/polyethylene terephthalate (PET) blends via melt extrusion. The content of the PET dispersed phase in the composite varied from 0 to 30 phr. The microstructure and morphology of the composites were characterized using scanning electron microscopy and Raman spectroscopy. The addition of PP‐g‐M‐E increased the interfacial interaction between the two phases and improved the compatibility and thermal stability of the system. In the presence of the compatibilizer, the crystallinity of the matrix phase (PP) increased, while that of the dispersed phase (PET) decreased owing to the heterogeneous nucleation effect of uniformly distributed PET. Double grafting of the PP‐g‐M‐E compatibilizer considerably enhanced the mechanical performance of the PP/PET blend system. The elongation at break of the modified sample exceeded that of the PP/PET blends by 117.55%, and the flexural and impact properties also showed considerable improvement.

Extruded benzene sulfonate modified poly(ethylene terephthalate)/polyamide 6 blends: An insight into the mechanism of compatibility improvement

Rheological Properties of PET/PA66/Liquid Crystalline Copolyesteramide Blends

Synergetic Effect of a Reactive Compatibilizer and Organo-montmorillonite on the Dispersion of Polyamide 6 /Polydimethylsilicone Blend with a High Viscosity Ratio

Compatibilizing Efficiency of Copolymer Precursors for Immiscible Polymer Blends

A Dissipative Particle Dynamics Study on the Compatibilizing Process of Immiscible Polymer Blends with Graft Copolymers

Study on ester-amide exchange reaction between PBS and PA6IcoT

Mutual Nucleating and Crystallization Behavior of Poly (ethylene Terephthalate)/polyamide 66 Blends

Study of polypropylene/polyethylene terephthalate blends compatibilized with polypropylene double‐grafted maleic anhydride and epoxy resin

Experimental Studies on the Phase Separation Behavior of Molten Benzenesulfonate-Modified PET/PA6 Blends

Compatibilization of Polyamide 6/Poly(2,6-Dimethyl-1,4-phenylene Oxide) Blends by Poly( Styrene-Co-Maleic Anhydride)

Joint Effect of Compatibilizer and Organo-Montmorillonite on Compatibilization of Polyamide-6/Poly(Phenylene Oxide) Blend: Morphology and Properties

Unlocking superior properties in polypropylene/polyethylene terephthalate (PP/PET) blends using an ethylene-butylene-acrylate terpolymer reactive compatibilizer

Study of Compatibility Between Laminar Structure and Barrier Properties of Polyethylene/Modified Polyamide Blends

Reactive Compatibilization of Polyamide 6/Olefin Block Copolymer Blends: Phase Morphology, Rheological Behavior, Thermal Behavior, and Mechanical Properties

Compatibilizing modification of polyethersulfone/polycarbonate blend

Molecular Compatibility of Polyamide 6 Blending with Thermal Liquid Crystalline Polyamide

Compatibilization And Toughening Of Immiscible Ternary Blends Of Polyamide 6, Polypropylene (Or A Propylene-Ethylene Copolymer), And Polystyrene

Fabrication of poly(ethylene terephthalate)/polypropylene-based elastomer blends with balanced stiffness-toughness: The effect of reactive compatibilization

Compatibility study of recycled Polypropylene (PP)/Poly(ethylene terephthalate) (PET) blends nanocomposites with PP‐g‐MAH: Modeling of twin screw extrusion

Influences of component ratio of minor phases and charge sequence on the morphology and mechanical properties of PP/PS/PA6 ternary blends

Study on the Microstructures and Mechanical Behaviour of Compatibilized Polypropylene/Polyamide-6 Blends