Abstract:The ultra-thin multilayer ceramics capacitors (MLCCs) with layer thickness less than 1 tm are in urgent demand due to the rapid development of modern electronic industries. However, the preparation of the dielectric materials with the desirable grain size <150 nm is a huge challenge. In this work, the ultra-fine BaTiO3 (BT) powders (<120 nm) prepared via solid-state reaction method, hydrothermal method and hydrothermal method following a heat treatment (850 degrees C) are selected to prepare the nano-crystalline non-reducible BT-based ceramics, respectively. The effect of the synthesis methods on the microstructure, electric performance and the reliability of the BT-based ceramics are studied. The results of the Raman, XPS and FT-IR spectroscopy demonstrate that a large number of internal stresses and point defects (hydroxyl/proton defects, Ba vacancies) are existed in the hydrothermal powders and can be eliminated to some extent by a proper heat treatment. Unfortunately, plenty of nano-pores (10-20 nm) are observed in the hydrothermal powders, which cannot be eliminated via the heat treatment or sintering process totally. As a result, the BT-based ceramic prepared by the solid-state powders has an absolute advantage in accelerating aging failure performance, compared to that prepared hydrothermal powders. The TSDC results indicate that the ceramic prepared by the solid-state powders has a lower oxygen vacancy concentration and a higher activation energy. Furthermore, a scaling analysis based on a RC equivalent model identifies the longer oxygen vacancy diffusion time for the ceramic prepared by the solid-state powders. All these features demonstrate that the solid-state ultra-fine BT powders are a promising candidate for the fabrication of the ultra-thin layer MLCCs. (C) 2020 Elsevier B.V. All rights reserved.

Synergism of Freeze-Drying and CAI to Obtain Narrowly Dispersed BaTiO3 Nanoparticles: A Step Towards Commercialization

Synergism of Freeze-Drying and CAI to Obtain Narrowly Dispersed BaTiO 3 Nanoparticles: A Step towards Commercialization

Synthesis of tetragonal BaTiO 3 powder with size and dispersity optimization via synergy mechanisms of combined dispersants

Preparation of Nano-Structured BaTiO3 Thin Film by Electrophoretic Deposition and Its Characterization

Significantly Enhanced Energy Storage Capability of BNT-based Ceramics Via Optimized Sintering Aids

Synthesis Of Tetragonal Batio3 Nano-Particle Via A Novel Tartaric Acid Co-Precipitation Process

Low-temperature synthesis of barium titanate thin films by nanoparticles electrophoretic deposition

Ultrahigh Energy Density and Efficiency of BaTiO3-based Ceramics Via Multiple Design Strategies

Synthesis and Performance of Tetragonal BaTiO3 Fine Powders Via a Facile Tartaric Acid Assisted Method

A Facile and Eco-Friendly Hydrothermal Synthesis of High Tetragonal Barium Titanate with Uniform and Controllable Particle Size

Sol‐Gel Routes to Nanostructured Patterned Ferroelectric Thin Films with Novel Electronic and Optical Functions

Pairing High Piezoelectric Properties and Enhanced Thermal Stability in Grain-Oriented BNT-based Lead-Free Piezoceramics

Fabrication of BaTiO 3 nanopowders with high tetragonality via two-step assisted rotary furnace calcination for MLCC applications

Liquid‐phase Preparation of BaTiO 3 Nanoparticles

Ferroelectric state and polarization switching behaviour of ultrafine BaTiO3 nanoparticles with large-scale size uniformity

Nanoscale grain sizes in BNT-based ceramics with superb energy storage performances via coating boron nitride nanosheets

Liquid-phase preparation of BaTiO<sub>3</sub> nanoparticlesInspec keywordsOther keywords

Liquid‐phase preparation of BaTiO3 nanoparticles

Synthesis and Characterization of Ba(Zr0.15Ti0.85)O3 Nano Powders by Oxalate Precipitation Method

High Reliable Non-Reducible Ultra-Fine BaTiO3-based Ceramics Fabricated Via Solid-State Method

Investigation into crystal structure-dielectric property correlation in barium titanate nanocrystals of different sizes