Abstract:All-solid-state lithium batteries (ASSBs) are considered like the next generation of electrochemical energy storage devices because of their safety and their high energy density up to 400Wh/kg. The all-solid-state battery is composed of a positive electrode (e.g., NMC (Li(Ni 1∕3 Mn 1∕3 Co 1∕3 )O 2 )), a negative one (Li), and a solid electrolyte, which is the critical component, composed of inorganic compound and/or solid polymer electrolyte (SPE) [1]. On the one hand, SPE have the advantage of an easy shaping with the technique already used in the manufacture of batteries and their flexibility allows obtaining a good interface with the electrode materials [2]. On the other hand, inorganic compounds generally have high ionic conductivity (10 -3 S/cm), they are stable electrochemically vs Li/Li + and their transport number is close to 1 to promote the diffusion/migration of Li + ions only. In order to combine the advantages of both types of materials, hybrid materials have been designed [3]. First, a new adaptable polymer matrix based on PEO derivatives has been developed. A solvent-free synthesis has been designed from liquid and commercial precursors Poly(ethylene glycol) methyl methacrylate (PEGM) and Poly(ethylene glycol) dimethacrylate (PEGDM). These latter were copolymerized with Lithium 3-[(trifluoromethane)sulfonamidosulfonyl] propyl methacrylate (MTFSLi). The anion TFSI - is thus grafted to the PEO network, allowing exclusively the diffusion of the Li + ion. This polymer matrix can be thus classified as single-ion conductor. In addition, the proportions between PEGM and PEGDM, acting as crosslinker, can be easily tuned. The PEGDM proportion controls the cross-linking density which modifies not only the glass transition temperature (Tg), but also the storage modulus (E’) and the free volume, and consequently the ionic conductivity of the polymer matrix which is the main property required for SPE. Finally, a ratio of PEGM:PEGDM (80:20) allows obtaining homogeneous SPE, self-standing and soft at room temperature, amorphous with a Tg of -41°C. The EO/Li ratio was then modulated in single-ion networks with the MTFSLi proportion, and an optimum in ionic conductivity of 2.10 -7 S/cm @25°C has been measured for EO/Li ratio of about 20. The transport number measured by the Bruce and Vincent method [4] was t + =1,0 for the single ion conductor, demonstrating the effective grafting of the counter anion. This value has been validated by measuring the diffusion coefficients of 7 Li and 19 F in NMR. To our knowledge, this is the first time a real unity transport number is reported in the literature for a polymer electrolyte. Moreover, the electrochemical stability of this single ion system extends from 0 to 6V vs Li + /Li. These experiments suggest the interest of using the single-ion polymer in the formulation of composite positive electrode with high potential cathode materials, due to its stability in potential. Li metal is considered the ultimate anode for Li-batteries. The long-term electrochemical stability has been evaluated in symmetric Li/polymer electrolyte/Li cell. The cell is cycled at a constant current density of 0.2 mA/cm 2 . After 200 h of cycling the voltage reaches solely 2V. Accordingly, the grafting of the anion to the network limits an overpotential in the cell, allowing a more stable system over time. Second, the garnet Li 6.4 La 3 Zr 2 Al 0.2 O 12 (LLZO) of the oxide family was associated to the previous polymer matrix. This garnet presents a high conductivity (10 -4 S/cm @ 25°C), a good chemical stability not only against lithium metal but also against air and humidity, which is not the case of sulphides homologues. A 3D-fibrous network obtained by the electrospinning method was carried out with a solution containing the inorganic precursors, a polymer and an appropriate solvent [5]. Then this membrane is calcined at 850°C to obtain the 3D fibrous network of LLZO. The resulting self-standing porous inorganic material (~80% of porosity) exhibits a conductivity of the order of 10 -6 S/cm @25°C. It was then impregnated with the polymer matrix precursors by capillarity and following by a polymerization. A self-standing membrane as thin as 80 μm containing 9%vol of LLZO was obtained. The conductivity of this hybrid membrane is comparable to that of the polymer (10 -7 S/cm @ 25°C). The resulting hybrid is mainly polymeric where the ionic conduction was realized by the polymeric matrix and the inorganic acts as a mechanical reinforcement. Preliminary results on high content of LLZO hybrid will also be presented, where a synergy of the both components is observed. [1] Janek . Nature Energy. 2016. Vol 1(9)p.16141. [2] Yue. Energy Storage Materials. 2016. Vol 5p.139-164. [3] Zheng. Chem Soc Rev. 2020. Vol 49p.8790-8839. [4] Bruce. Solid State Ion . 1988. Vol 28–30 p.918–922. [5] A. La Monaca . Electrochemistry Communications. 2019. Vol 104p.106483. Figure 1

Polydopamine-Coated Garnet Particles Homogeneously Distributed in Poly(propylene carbonate) for the Conductive and Stable Membrane Electrolytes of Solid Lithium Batteries

Polydopamine Coated Lithium Lanthanum Titanate in Bilayer Membrane Electrolytes for Solid Lithium Batteries

Ultrathin Li 6.75 La 3 Zr 1.75 Ta 0.25 O 12 -Based Composite Solid Electrolytes Laminated on Anode and Cathode Surfaces for Anode-free Lithium Metal Batteries

Surface Coating on a Separator with a Reductive Solid Li-Ion Conductor for Dendrite-Free Li-Metal Batteries

Sacrificial Polypropylene Carbonate Membrane for Dispersing Nanoparticles and Preparing Artificial Solid Electrolyte Interphase on Li Metal Anode.

Garnet/polymer solid electrolytes for high-performance solid-state lithium metal batteries: The role of amorphous Li2O2

Organic Cationic-Coordinated Perfluoropolymer Electrolytes with Strong Li+-Solvent Interaction for Solid State Li-Metal Batteries

Combining Organic Plastic Salts with a Bicontinuous Electrospun PVDF-HFP/Li7La3Zr2O12 Membrane: LiF-Rich Solid-Electrolyte Interphase Enabling Stable Solid-State Lithium Metal Batteries.

Flexible PVA/BMIMOTf/LLZTO composite electrolyte with liquid-comparable ionic conductivity for solid-state lithium metal battery

3D core-shell nanofibers framework and functional ceramic nanoparticles synergistically reinforced composite polymer electrolytes for high-performance all-solid-state lithium metal battery

Flexible PVDF-HFP based hybrid composite solid electrolyte membrane co-filled with hydroxypropyl methyl cellulose and Li6.4La3Zr1.4Ta0.6O12 for high-performance solid-state lithium batteries

Conception of Hybrid Organic-Inorganic Membrane as New Electrolyte in All Solid-State Battery

Well‐Dispersed Polydopamine In Situ Coated Lithium Montmorillonite Nanofillers Composite Polyethylene Oxide‐Based Solid Electrolyte for All‐Solid‐State Lithium Batteries

Enhanced Interphase Ion Transport via Charge‐Rich Space Charge Layers for Ultra‐Stable Solid‐State Lithium Metal Batteries

Mechanically Reinforced Pseudosolid Polyelectrolyte Membranes via Layer‐by‐Layer Assembly for High‐Performing Lithium‐Metal Batteries

Porous Polymer Membrane with Uniform Lithium-Ion Transport Via Phase Separation for Stable Lithium Metal Batteries

A Sandwich Structure Composite Solid Electrolyte with Enhanced Interface Stability and Electrochemical Properties For Solid-state Lithium Batteries

Three-dimensional Structured Asymmetric Electrolytes for High Interface Stability and Fast Li-ion Transport in Solid-State Li-metal Batteries

Polyvinylidene fluoride nanofibers with embedded Li6.4La3Zr1.4Ta0.6O12 fillers modified polymer electrolytes for high-capacity and long-life all-solid-state lithium metal batteries

Composite Polymer Electrolyte with Vertically Aligned Garnet Scaffolds for Quasi Solid-State Lithium Batteries

Composite Hybrid Quasi-Solid Electrolyte for High-Energy Lithium Metal Batteries