Abstract:The microstructure and mechanical properties of Fe-0.19C-1.46Mn-1.50Si, a low-carbon hot-rolling direct quenching and partitioning steel, were investigated, and particular emphasis was placed on the effects of the rolling temperature and the subsequent cooling method. Once rolling occurred above the recrystallization temperature, the grain size of prior austenite could be reduced from ∼88.2 to ∼11.8 μm. The corresponding packet and block sizes of martensite could be reduced from ∼17.6 to ∼4.3 μm and from ∼9.0 to ∼1.8 μm, respectively, after a typical two-step quenching and partitioning (Q&P) treatment following rolling immediately. Once rolling occurred below the recrystallization temperature, deformed prior austenite with a grain length and width of ∼150 and ∼60 μm, respectively, were obtained. Consequently, only the block size would be reduced to ∼1.9 μm. The volume fraction of retained austenite (RA), which was ∼11% in the specimens, was not significantly affected by the rolling temperature. Further, if the typical two-step Q&P treatment was replaced by air cooling after the rolled specimen was quenched to the martensitic start temperature, the volume fraction of RA in the specimen was reduced to ∼7.4%, and the corresponding carbon depletion degree in the martensitic matrix was decreased as well. Tension and impact tests indicated that the cooling method was more critical than the rolling temperature for determining the mechanical properties. The presence of sufficient amounts of RA and carbon depletion in the refined martensitic matrix contribute to the strong strain hardening and energy absorption capabilities of the steel together. As a result, rolling at a temperature that was slightly higher than the recrystallization temperature combined with the typical two-step Q&P treatment could be an optimized process to obtain excellent comprehensive mechanical properties. In particular, the ductile-to-brittle transition temperature (DBTT) could be reduced from −10°C to −30°C.

Effects of Cold‐Rolling Reduction on Microstructure, Thickness, Surface Roughness of AS20/20 and on Bending Toughness of AS20/20‐Coated Press‐Hardened Steel

Effect of Cold Rolling on Microstructure and Mechanical Property of a Novel (fe50mn30co10cr10)97c2mo1 High Entropy Alloy

Effect of Cold Rolling Reduction Ratio on Microstructure and Mechanical Properties of Fe–10Mn–4Al-0.4C Steel Containing Δ Ferrite

Investigation on Mechanical Properties and Oxidation Behavior of 1.2 and 1.7 GPa Grades Coating-Free Press-Hardened Steels

Effects of cold-pre-rolling reduction on precipitation of 2519A aluminum alloy plate

Effect of Cross-Rolling on the Hardness of the AlSi10Mg Alloy Fabricated through Powder Bed Fusion

Effect of Al-Si Coating on Weldability of Press-Hardened Steels

Effects of Deep Cryogenic Treatment and Controlled Rolling on Microstructures and Mechanical Properties of an Ultra High Strength Steel

Fracture Strain of Al-Si-Coated Press-Hardened Steels under Plane-Strain Bending

Effect of pack rolling on microstructures and tensile properties of as-forged Ti-44Al-6V-3Nb-0.3Y alloy

Effect of Cold-rolling on Mechanical Properties and Microstructure of an Al-12%Si-0.2%Mg Alloy

Effect of Hot Rolling on Microstructural Evolution and Wear Behaviors of G20CrNi2MoA Bearing Steel

Effect of Intercritical Deformation on Microstructure and Mechanical Properties of A Low-Silicon Aluminum-Added Hot-Rolled Directly Quenched and Partitioned Steel

Effect of asymmetric rolling and subsequent ageing on the microstructure, texture and mechanical properties of the Al-Cu-Li alloy

Effect of Rolling Reduction on Microstructures and Mechanical Properties of Sc-Containing Al-3.2Cu-1.5Li Alloy

Comparing Mechanical and Oxidation Properties of Cr- and Si-Alloyed Press-Hardened Steel with 22mnb5 Steel at Various Heating Temperatures

Microstructure and mechanical properties of a low-carbon HDQ&P steel

Microstructures, Mechanical Properties and Deformation of Near-Rapidly Solidified Low-Density Fe-20Mn-9Al-1.2C-xCr Steels

Influence of Thermal Modification on Al-Si Coating of Hot-Stamped 22mnb5 Steel: Microstructure, Phase Transformation, and Mechanical Properties

Importance of cold rolling and tempering on the microstructure evolution, precipitation behavior and mechanical responses of 9Cr3Co3W1Cu ferritic/martensitic steel

Microstructure, Texture, and Anisotropic Properties of High-Strength Low-Alloy Steel